PEUGEOT EnergyScroll-457V90 Scroll Saw with Variable Speed
Description and location of machine parts
Contents of box
Machine assembly
Vibrations from the machine can cause it to move and make cutting difficult; it is recommended to fix the saw on a stable support.
Assembly of the main casing
Electronic speed variator
Before any operation on maintenance of the machine, disconnect it from the mains
Machine use
Open the dust extraction cover before changing the blade
- Relax the swing arm
- Press on the arm to be able to mount the blade on its support
- Replacing a blade with pins
- Secure the end to the lower arm
- Blade teeth down
- Lower the upper arm and secure the blade, then tighten the blade by turning the dial as shown below
- Replacing a blade without pins
- Close the dust suction cover to connect a vacuum cleaner
- Adjustable blow gun on flexible hose, for a dust-free work area
- Compartment for blade storage
- Tighten the swinging arm to tighten the blade; This must be very straight: if it is curved, the tension is not strong enough. If the blade does not move when you put pressure on
- it, the tension is too strong: high risk of breakage. Vibrate the scroll saw blade and listen to the sound it produces. A low or soft sound indicates that the tension is too low, a high sound indicates optimal tension. Be careful not to overtighten the blade, however.
Maintenance, recommendations and advice
Transport
Transportation of the machine
Consumables replacement
Opcional
Blade kit 6 dowel blades 18 Tpi / 6 dowel blades 10 Tpi / 12 round blades, l=0.88 mm / 12 universal flat tip blades 12 Tpi / 12 universal flat tip blades 20 Tpi
Mes met nokken
This Universal blade is very effective in hardwoods and mediums. This range of blades allows the complex cutting as well as rough work patterns.
- Ref 803200 (x6 – 15 TPI) 803200
- Ref 803201 (x6 – 18 TPI) 803201
- Ref 803202 (x6 – 25 TPI)803202
Plat mes
It produces a quick job and leaves a clean surface state and end
- Ref 803280 (x12 – 25 TPI) 803280
- The metal type teeth and specific heat treatment make this blade very powerful in ferrous and non ferrous metals up to 2 mm.
- Ref 803206 (x6 – 35 TPI) 803206
- This Universal blade is very effective in hardwoods and mediums. This range of blades allows the complex cutting as well as rough work patterns.
- Ref 803209 (x12 – 12 TPI) 803209
Ref 803220 (x12 – 9 TPI) 803220
Spiraalvormig mes –The helical gear teeth 360 ° allows cutting in all directions. Powerful blade in many materials.
- Ref 803228 (x12 – 48 TPI) 803228
- Ref 803229 (x12 – 28 TPI) 803229
Technisch mes
- Allows both the rapid breakdown and complex cutting (up to 65 mm thick). Optimal sawdust evacuation.
- This arrangement of teeth with a wider space between two teeth PREVENTS WARMING of wood. For a clean and fine finish. Excellent in soft woods.
- Ref 803288 (x12 – 8/6R TPI) 803288
- Ref 803283 (x12 – 15 TPI) 803283
EnergyScroll-457V90 132155 132155
80 W (S1)
S1 SERVICE CONTINU
- Nominal power:
120 W (S2 : 15 min)
S2
SERVICE TEMPORAIRE
- Nominal power:
Subjected to recycling :
Waste recycling:
The tools, accessories and their packaging must use an appropriate recycling channel. In compliance with European Directives 2012/19/UE and 2006/66/CE, a product’s components must be separated, collected, recycled or eliminated in accordance with the environmental regulations in force. The appliance, batteries, oils and packaging must be deposited in the special waste elimination systems such as the waste collection centres. Ask your commune for information on the nearest organisation in a position to reprocess or collect this waste
EnergyScroll-457V90
DECLARATION OF CE CONFORMITY
PEUGEOT OUTILLAGE
192, Avenue Yves
- Fax : 02 36 16 71 40
Declares that,
CODE
EnergyScroll-457V90
Complies with the EEC standards:
- 2006/42/EC 2014/30/EU 2011/65/EU
- ENIEC55014-1:2021
- ENIEC55014-2:2021
- ENIEC61000-3-2:2019+A1:2021
- EN61000-3-3:2013+A1:2019+A2:2021
- EN62841-1 :2015+A11 :2022/ISO 12100 :2010
SIGMA
Christophe HUREL
20/02/2024
Standards Technical services, Shanghai, Co., Ltd.
WARRANTY
- Scope of the warranty :
The warranty shall only apply to manufacturing defects or material defects.
We are obliged to exchange or repair parts that are identified as being unusable - Lifetime warranty :
The warranty shall be valid for 60 months from the delivery date of the equipment to the user (invoice or till receipt must be provided).
Exchanges or repairs carried out under the warranty shall not extend the original warranty period.
The user shall be responsible for original shipping charges. - Reservations :
The warranty shall not under any circumstances cover repairs carried out by a non-authorised repairer.
The equipment should not be dismantled under any circumstances during the warranty period.
- Purchase date
- Machine code
- Distributor’s stamp
AFTER SALE SERVICE
PEUGEOT OUTILLAGE – 192, Avenue Yves Farge – 37700 St. Pierre-des-Corps –
PEUGEOT OUTILLAGE
contact@peugeot-outillage.com peugeot-outillage.com
FAQ
- Q: What type of materials can be cut using this scroll saw?
A: The EnergyScroll-457V90 is suitable for cutting hard and semi-hard woods, as well as metals up to 2mm thickness. - Q: How do I choose the right scroll blade for my cutting needs?
A: Different scroll blades are available with varying TPI (teeth per inch) counts for different cutting patterns and materials. Refer to the provided references for blade selection based on your requirements.
Documents / Resources
![]() |
PEUGEOT EnergyScroll-457V90 Scroll Saw with Variable Speed [pdf] Instruction Manual EnergyScroll-457V90 Scroll Saw with Variable Speed, EnergyScroll-457V90, Scroll Saw with Variable Speed, Variable Speed |