PERLEGEAR PGLT5 TV Wall Bracket Instruction Manual

Please carefully read all instructions before attempting installation. If you do not understand the instructions or if you have any questions or concerns, please call technical support or email customer service.
Before starting assembly, verify that all parts are included and undamaged. Do not use damaged or defective parts. If you require replacement parts, please call technical support or email customer service.
Not all hardware included in this package will be used.

CAUTION

Avoid the risk of personal injury or property damage!
Do not use this product for any purpose that is NOT explicitly specified in this manual. Do not exceed the maximum weight capacity. We are not liable for damage or injury caused by incorrect assembly, improper mounting, or inappropriate use.

WARNING

This product is designed for installation on wood stud, solid concrete, and brick walls. DO NOT install on drywall alone.
The wall must be capable of supporting four times the weight of the TV and mount combined.
This product contains small parts that may pose a choking hazard.

Note for Wood Stud Installation (Page 10-11)

Avoid the risk of personal injury or property damage! Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtighten). Do not use a drill; only use a socket wrench.
Do not use wall anchors for this mounting option. Wall anchors are used for solid concrete and brick wall installations only.
Minimum wood stud size: 1 1/2″ W x 3 1/2″ D (38 x 89mm)
Wood stud spacing: 16″ to 24″ (406mm to 610mm) (center to center)

Note for Solid Concrete or Brick Wall Installation (Page 12-13)

Avoid the risk of personal injury or property damage! Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtighten). Do not use a drill; only use a socket wrench.
Mount the wall plate directly on the concrete surface.
Minimum solid concrete thickness: 8″ (203mm)
Never drill into the mortar between bricks.

Before getting started, make sure this mount is compatible.

VESA Pattern Compatibility
☑ 200 * 100mm
☑ 200 * 200mm
☑ 200 * 300mm
☑ 200 * 400mm
☑ 300 * 200mm
☑ 300 * 300mm
☑ 300 * 400mm
☑ 400 * 200mm
☑ 400 * 300mm
☑ 400 * 400mm
☑ 500 * 400mm
☑ 600 * 400mm

If the TV weighs more than 132 lbs (60kg), do not use this product.

Suitable for installation on wood stud, solid concrete, and brick walls. DO NOT install on drywall alone. NOTE: For steel stud installation, “SNAPTOGGLE” type bolts are required (not included).
Tools Needed (Not Included)

Step 1 Attach TV Brackets to the TV

1-1 Select TV Bolts

Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M6 or M8) to use. A minimum of 4-5 turns into the threading is required. Do not turn past the bottom of the hole.

1-2 Spacer and Bolt Configurations

If your TV has a bump, the spacer can be placed above or below the TV brackets to make the TV brackets flush from the top to bottom.

The TV brackets should be leveled flush from the top to bottom.

Step 2 Assemble the Wall Plate

Step 3 Mount the Wall Plate on the Wall

• Option A: For Wood Studs, follow Page 10 to 11.
Option B: For Solid Concrete or Brick Walls, follow Page 12 to 13.

Use a stud finder to locate wood studs, or use an awl to find the edges. Mark the edge and center positions. Position the wall plate at your desired height and line up the holes with your stud centerline. Level the wall plate and mark the holes.

Drill 4 pilot holes using a 5/32″ (4mm) diameter drill bit. Make sure the depth is not less than 2 3/4″ (70mm). Mount the wall plate on the wall using the lag screws [A1]. Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtighten).

Position the wall plate at your desired height. Level the wall plate and mark the holes. Drill 4 pilot holes using a 3/8″ (10mm) diameter drill bit. Make sure the depth is not less than 3″ (75mm). Never drill into the mortar between bricks.

Use a hammer to tap the anchors [A2] into the drilled holes. Ensure the anchors are seated flush with the concrete or brick surface. Mount the wall plate on the wall using the lag screws [A1] and anchors [A2]. Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtighten).

Step 4 Verify that the Wall Plate is Firmly Mounted

Step 5 Attach the Decorative Cover

Step 6 Set the Tilt Angle of the TV

Adjust the hooks on both TV brackets to the same desired angle. You may need to slightly loosen the tilt tension bolts [T]. Retighten tilt tension bolts [T] to secure the tilt angle. If you make the angle too large, the brackets may not fit over the wall plate.

Step 7 Hang the TV on the Wall Plate

7-1 Hang the TV with brackets on the wall plate.
7-2 Pull both cords [R] down to open the latches, then push them forward toward the wall. The latches should engage on the wall plate. Release the cords to lock the TV in place. If latches did not engage, pull cords and try again.

Step 8 TV Removal

To remove the TV, first disconnect all cables. Pull the cords [R] down and hold them while gently pulling the bottom of the TV away from the wall plate. Exerting too much force may cause the latches to break. Once the latches are free, lift the TV up and off of the wall plate.

Step 9 Adjust the Tilt Angle of the TV

Tilt the TV to the desired angle. You may need to adjust the tilt tension bolts [T]. Do not overtighten or overloosen the bolts. If you cannot access the tilt tension bolts, you may need to remove the TV, adjust the tilt angle, then remount the TV.

FAQs

Question: How can I raise or lower the TV if the TV Wall Mount is already fixed on the wall?

Answer: 1. Remove the TV from the TV Wall Mount. 2. Remove the TV brackets from the TV and reattach according to instructions A or B in the picture below (A for lifting up the TV or B for lowering the TV). 3. Hang the TV on the TV Wall Mount and secure.

A. To raise the TV by a few inches, reattach the TV brackets using the upper holes in the brackets.
B. To lower the TV by a few inches, reattach the TV brackets using the lower holes in the brackets.

1-800-456-5231 (US/CA)
44-808-196-4165 (UK)
support@perlegear.com
www.perlegear.com
AMZLAB GmbH
Laubenhof 23,45326 Essen
info@amz-lab.de
THEMIS AR support Itd.
85 Great Portland St, London, United Kingdom.
info@amz-lab.de
Manufacturer: BESTQI INNOVATION (HONG KONG) TECHNOLOGY CO., LIMITED Address: FLAT/RM 185 G/F HANG WAI IND CENTRE 6 KIN TAI ST TUEN MUN NT

Documents / Resources

	PERLEGEAR PGLT5 TV Wall Bracket [pdf] Instruction Manual PGLT5 TV Wall Bracket, PGLT5, TV Wall Bracket, Wall Bracket, Bracket
	Perlegear PGLT5 TV Wall Bracket [pdf] User Manual 860-03826-00 V1, PGLT5-E-listing-JPZJY, PGLT5 TV Wall Bracket, PGLT5, TV Wall Bracket, Bracket

References

User Manual

IMPORTANT SAFETY INFORMATION