Pandora V4 FD Invetec Pro Instructions

To enter the programming mode, press the VALET button until the system enters programming mode.
Use the programming table to navigate through different functions and settings.

Exit the programming mode by following the specified methods in the manual, such as unplugging the USB cable and reconnecting the main power supply.

FAQ

Q: How do I know if the system is in programming mode?
- A: The system will display specific indicators, such as LED lights or beeping sounds, to signal that it is in programming mode.
Q: Can I pair devices that are not included in the system?
- A: Yes, you can pair additional devices following the pairing instructions provided for each device type in the manual.

“`

View Fullscreen

Pandora Smart Pro v4 (hereinafter referred to as the System) is a car service-security system built for cars with on-board voltage of 12V. It is a complex engineering solution, which includes unique and modern technological software and hardware solutions. While developing the Pandora Smart Pro v4 we were using the most up-to-date electronics from world’s best manufacturers. The Pandora Smart Pro v4 is built using high-precision mounting and control machinery, thus we guarantee highest possible quality, reliability and stable technical characteristics for the whole operation period.

The system has a cryptographically strong authorization code with unique dialog algorithm and individual encryption key on every device. It guarantees protection form electronic hacking for the whole operation period.

Our web-site: pandorainfo.com
Customer support: support@pandorainfo.com

Read before using

Carefully read this manual before starting installation and using the security-service system. Pay attention to text marked with !

• THE SECURITY AND TELEMETRIC SYSTEM IS A COMPLEX TECHNICAL PRODUCT. SYSTEM INSTALLATION AND CONFIGURATION MUST BE CARRIED OUT ONLY BY A SKILLED PROFESSIONAL.

! FEATURES AND SYSTEM MODES, CONTROL OF THE VEHICLES ZONES DEPEND ON THE TYPE OF CONNECTION AND SYSTEM SETTINGS ORIGINAL VEHICLE OPERATION LOGIC AND TRIM.

! THE SYSTEM SET INCLUDES THE “OWNER’S PERSONAL CARD”. THIS CARD CONTAINS INFORMATION UNDER A PROTECTIVE LAVER THAT IS INTENDED ONLY FOR THE OWNER OF THE SYSTEM. MAKE SURE THAT THE PROTECTIVE LAYER ON THE OWNER’S PLASTIC CARD IS INTACT AFTER THE INSTALLATION OF THE SYSTEM. READ THE “OWNER’S PERSONAL CARD” SECTION OF THIS MANUAL BEFORE ERASING THE PROTECTIVE LAYER.

• WHEN SYSTEM INSTALLATION IS FINISHED:
• CHECK THE SYSTEM OPERATION AND FUNCTIONS WITH A SPECIALIST.
• WE RECOMMEND THAT YOU MARK EACH WORKING FUNCTION WITH A SIGN M. IN THE “CONTROL THE SYSTEM” SECTION
• CHECK THAT THE “INSTALLATION CERTIFICATE” AND “WARRANTY CARD” ARE FILLED OUT. THESE DOCUMENTS MAY BE REQUIRED FOR CONTACTING THE CUSTOMER SUPPORT.
• ASK AN INSTALLER TO MARK THE LAYOUT OF THE SYSTEM COMPONENTS ON THE DIAGRAM. THIS INFORMATION MAY BE REQUIRED FOR DIAGNOSTIC/CONFIGURING OR EMERGENCY DEACTIVATION OF THE SYSTEM.
• WE RECOMMEND THAT YOU CHANGE THE DEFAULT VALUE OF THE PIN-CODES OF THE SYSTEM. YOU CAN WRITE DOWN THE CHANGED PIN-CODES IN THE “PIN-CODES OF THE SYSTEM” SECTION.

PIN-codes of the system

The “Secret PIN-code”
(is written on the “Owner’s personal card”)
The “Service PIN-code”
(default value is 1-1-1-1)
The “Guest PIN-code”
(default value is 1-2-3-4)
The “Immobiliser PIN-code”
(is used for the Validator (pin-to-drive) function)
The “Beach mode PIN-code”
(is used for Beach mode function)

External VALET button

An external VALET button with a two-color status LED indicator is placed inside a vehicle (see the “System modules layout” section).
The button is used for programing the system, arming/disarming, activating/ deactivating immobiliser modes.

System modules layout

External VALET button
(VALET button via CAN)
Button for the Immobiliser
PIN-code
Button for Beach mode
PIN-code
) Circuit being blocked
5 Base unit
6 • Beeper

Base unit

Built-in LTE module (4G/3G/2G | GPS/GLONASS) – provides a connection with our online service pandora-on.com and mobile application, allows to control the system by a phone using DTMF commands, voice and SMS notifications, LBS-coordinates (only by DTMF -command), automatic date and time detection, precise GPS location (with Tracking function).

Built-in nano-SIM port – is used to work with the built-in GSM modem.

I THE SIM-CARD SHOULD BE REPLACED AND THE FOLLOWING SETTINGS SHOULD BE PERFORMED ONLY BY A QUALIFIED SPECIALIST. 2.4GHz radio channel, Bluetooth 5.0 protocol (BT5.0) – supports up to 14 additional Bluetooth devices (see the “Additional devices” section), including a mobile phone.

Built-in 3D accelerometer – is used to detect shock motion/tilt including 2 separate zones of shock sensor (alarm and warning), the system allows to adjust sensitivity of each zone, to use data from the accelerometer to block the engine and close the central lock on movement. Temperature sensors – allow the system to measure temperature of different zones to send this information to the remote control or mobile apps. The following zones are available: interior temperature – built in sensor of the main unit, engine temperature – external temperature sensor (see the “System set”), outside temperature – digital car protocol*

The system settings allow you to reassign sensor to different zones and use information from external additional devices (PS-331BT, RHM-03BT, DMS-100BT/101BT/105BT); to implement automatic engine or engine pre-heater starts and stops by temperature. Built-in digital 2xFD-CAN/2xCAN/BEAN BUS/LIN* interface – allows the system to read statute
and exucute commands via digital buses, and work with Webasto Thermo Top Evo u Eberspacher Hydronic 1/2/3.
Built-in digital IMMO-KEY port and immobiliser bypass* – hardware and software algorithms with the special Pandora CLONE server allow the system to bypass original immobilisers for automatic and remote engine starts.
Built-in USB port – update and configuration of the system using a PC and Pandora Specialist.
• *THE OPERATION OF THE SYSTEM DEPENDS ON THE FUNCTIONS DECLARED BY THE MANUFACTURER FOR A PARTICULAR VEHICLE. IT
RECOMMENDED TO CONSULT WITH A QUALIFIED SPECIALIST BEFOREHAND ABOUT THE AVAILABILITY OF THESE FUNCTIONS.

Indication of the SEND LED

SIGNALS DESCRIPTION

one flash confirmation of arming low battery level (when installing a battery) two flashes confirmation of disarming three flashes high battery level (when installing a battery) faded constant light battery is discharged (when installing a battery, when the button is pressed)

Installation/replacing a battery of the tag CR2032

When installing or replacing the battery (CR2032), you must carefully follow the following steps:

• unscrew the screw with a Philips PH00 screwdriver (fig. 1);
• slide the battery cover in the direction shown by the arrow (fig. 2); remove the battery and install a new one in accordance with the correct polarity: the SEND indicator will produce 3 red lights if a quality battery is installed;
• assemble the taq in the reverse order.

IMMOBILISER RADIO TAG

A radio tag is a device used to control a vehicle/system on a distance of a Bluetooth connection. The tag is also used as an authorization device for «Immobiliser/Anti-Hi-Jack/Hands Free» modes. The radio tag has: a control button for arming/disarming and activating/deactivating Service mode, a built-in accelerometer, which allows the tag to go in the energy saving mode when there is no movement and LED indicator SEND.

FOR CORRECT OPERATION, IT IS NOT RECOMMENDED TO PLACE THE RADIO TAG NEAR THE METAL OBJECTS, MAGNETIC AND ELECTRONIC DEVICES (CREDIT CARDS, PHONES, KEYS, REMOTES, ETC.). DO NOT EXPOSE THE RADIO TAG WITH HIGH TEMPERATURES, MOISTURE, OR STRONG IMPACTS. IT IS RECOMMENDED TO PLACE THE RADIO TAG ON THE BELT IN AN INDIVIDUAL CASE OR IN THE FRONT POCKET OF CLOTHING.

LED indicator

SEND
Control button
Antenna
2,4GHz (Bluetooth)
Pandora
Built-in accelerometer
Battery
CR2032 –
– – -•
Functions of the button PRESS

•- short press
(when ignition is off)
– press and hold for 1 sec.
(when engine is running)
•- press and hold for 2 sec. (when system is disarmed)
– press and hold for 3 sec. (when ignition is on)
– press and hold for 6 sec. (in programming mode)

DESCRIPTION

System arming/disarming
Activation of «Ignition hold on» mode
Change the «Main owner phone number»
Activating/deactivating Service mode Pairing a tag with the base unit

ONLINE SERVICE AND MOBILE APPLICATIONS

Telemetric functions of the system allow you to control your vehicle using the online service pandora-on. com or mobile app – Pandora Connect. A SIM card with Internet access is installed in the system to provide this functionality.
When approaching the vehicle or when Internet connection is missing a mobile phone with the app installed can work with the system via a Bluetoothconnection. The mobile phone must be paired with the system.

pro.p-on.ru

e-mail
********
LOGIN
PASS
PANDORA
CONNECT
e-mail
LOGIN
********|
PASS

I FOR THE CORRECT OPERATION OF THE GSM FUNCTIONS, AN OWNER SHOULD MONITOR THE STATUS/ BALANCE OF THE SIM CARD INSTALLED IN THE SYSTEM. IF THE SIM CARD IS BLOCKED OR DEFECTIVE, GSM FUNCTIONS OF THE SYSTEM WILL BE UNAVAILABLE.

Before using the online-service, it is necessary to create an account (Registration), login to your account (using your email and password created on the registration step) and add the system to your account (enter information from the Owner’s personal card).

Web-service: https://pandora-on.com.

The Pandora Connect mobile app is available for downloading from the corresponding app store: App Store for iOS devices; Google Play for Android devices. Download on the

App Store

GET IT ON Google Play

I THE MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES OF THE
• INTERFACE AND FUNCTIONALITY OF THE INTERNET SERVICE AND MOBILE APPLICATION WITHOUT NOTIFYING THE CONSUMER.

Writing a mobile device to the system memory

hen approaching the vehicle or when Internet connection is missing a mobile phone with the \mobile application Pandora Connect installed can work with the system via a Bluetooth connection. \This type of connection allows you to control the system, receive status information and use your mobile phone as an authorization device. After installing the mobile application pair your mobile device with the system.

THE SYSTEM SUPPORTS BLUETOOTH CONNECTION ONLY WITH ONE MOBILE DEVICE.

I. ENTER THE PROGRAMMING MODE Use the VALET button to enter the «Service PIN-code» (default value is 1-1-1-1). See the detailed description of the procedure in the «Control over the system in case of emergency» section.

II. ENTER THE «PAIRING A MOBILE PHONE» PROGRAMMING LEVEL After entering programming mode, press and hold the VALET button for 5 seconds (until the fifth signal of the siren/beeper). The system will enter the «Pairing a mobile phone» programming level. The LED indicator will light green, the system is ready for pairing. THE PREVIOUSLY PAIRED DEVICE WILL BE ERASED FROM THE SYSTEM MEMORY AFTER ENTERING THE LEVEL.

III. PAIR A MOBILE DEVICE

Enable the Bluetooth connection in the mobile device, enter the app settings, click «Bluetooth control», click «Not defined». In the search box, establish a connection with the detected system. The red and green flashes of the «LED» indicator light and a single siren sound will confirm the pairing.

IF THERE IS NO AUTOMATIC PAIRING, ENABLE THE «PIN REQUEST FOR PHONE PAIRING» ITEM IN THE «RADIO TAG AND MOBILE DEVICE FUNCTIONS» SETTINGS AND MAKE THE PAIRING PROCEDURE AGAIN. A MOBILE DEVICE WILL REQUEST A PIN-CODE (DEFAULT VALUE IS 0-0-1- 1-1-1 WHERE 4 LAST DIGITS ARE THE «SERVICE PIN-CODE». THIS SETTING SHOULD BE MADE BY A QUALIFIED TECHNICIAN.
IV. EXIT PROGRAMMING MODE Turn on the ignition and then turn off to exit programming mode.

ADDITIONAL DEVICES

Bluetooth remote R-500BT R-468BT is a one-way short-distance communication device designed to control a security system. The remote control can be used as an owner authorization device.

CONTROL COMMANDS

Arming/Disarming | Trunk | Remote engine start | Engine pre-heater STATUSES

Immobiliser | Anti-Hi-Jack| Hands Free

RADIO INTERFACE 2.4GHZ (BLUETOOTH) | THREE CONTROL BUTTONS | SOUND INDICATOR |

LED INDICATOR | CR2032 BATTERY

Immobiliser radio tag BT-785 / 780 | BT-770 | BT-765 / 760(V) is a
one-way short-distance communication device designed to control a
security system. The tag can be used as an owner authorization device.
CONTROL COMMANDS
Arming/Disarming | Service mode
OWNER AUTHORIZATION

Immobiliser | Anti-Hi-Jack Hands Free

RADIO INTERFACE 2.4GHz (BLUETOOTH) | CONTROL BUTTON LED INDICATOR MOTION
SENSOR | CR 2032 BATTERY

Blocking radio relay BTR-101V | BTR-101 is a wireless device designed to perform blocking engine blocking based or not based on car movement. RADIO INTERFACE 2.4GHz (BLUETOOTH) BUILT-IN BLOCKING RELAY (NC) MOTION SENSOR

DMS-105BT | DMS-101BT | DMS-100BT is a wireless device designed to monitor internal or external perimeter state: any security zone can be assigned to the Hall/shock/tilt sensor state; temperature monitoring.

The sensor can be installed on a door, hatch, trunk, trail, garage door. DMS-105BT: RADIO INTERFACE 2.4GHZ (BLUETOOTH) | HALL SENSOR | TEMPERATURE SENSOR SHOCK/TILT SENSOR WATER SENSOR WATERTIGHT CR123A BATTERY DMS-101BT: RADIO INTERFACE 2.4GHZ (BLUETOOTH) HALL SENSOR TEMPERATURE SENSOR | SHOCK/ TILT SENSOR | 2xCR2450 BATTERIES DMS-100BT: RADIO INTERFAce 2.4GHz (BLUETOOTH) Hall sENSor

TEMPERATURE SENSOR | SHOCK/TILT SENSOR | CR123A BATTERY

Movement sensor PIR-100BTM | PIR-100BT is a wireless device designed to monitor internal volume of a vehicle for thermal movement.
PIR-100BTM: RADIO INTERFACE 2.4GHZ (BLUETOOTH) | PIR-SENSOR | REMOVAL
SENSOR Shock/TilT senSor CR123A BATTERY
PIR-100BT: RADIO INTERFACE 2.4GHz (BLUETOOTH) | PIR-SENSOR | REMOVAL SENSOR | CR123A BATTERY

WARRANTY

WARRANTY OBLIGATIONS

Manufacturer guarantees correct operation of the service-security system if exploitation, installation, storage and transportation conditions described in this manual were met. The system should only be used according to installation scheme and user manuals. The system is meant to be installed by the professional car electronics installers. The installer should fill in installation certificate that is included in this manual. Parts malfunctioning during warranty period on the fault of the manufacturer should be repaired or replaced by the installation center of the manufacturer or by certified service center. List of certified service centers can be found on pandorainfo.com

The user loses the right for warranty services in the following cases:

• when warranty period expires;
• if exploitation, installation, storage or transportation conditions were not met;
• if there is mechanical damage of the external parts of the system after it is sold.

This includes: fire damage, consequential damage in case of car accident, aggressive liquids and water seeping damage, damage caused by improper use;

• if the damage was caused with incorrect settings and parameter adjustment;
• if system devices are replaced with any devices that are not recommended by the manufacturer;
• if manufacturer sealing is broken;
• if there is no properly filled warranty card and installation certificate.

Warranty period is 3 years since the moment of purchase, but no more than 3.5 (three and a half) years since the moment of production. This warranty does not include batteries of the remotes, as they have their own service lifetime. Maintenances and repairs of the system with expired warranty period are carried out at the expense of the user on a separate contract between the user and the installer/service center.

OWE RECOMMEND THAT YOU ASK AN INSTALLER TO FILL OUT THE INSTALLATION CERTIFICATE AND THE WARRANTY CARD. THESe DOCUMENTS MAY BE REQUIRED FOR CONTACTING THE CUSTOMER SUPPORT.

WARRANTY CARD
Pandora Smart Pro v4
Serial number
Date of purchase «_
Seller’s (installer’s) stamp
Seller’s signature
_ 20_
_year

Documents / Resources

Pandora V4 FD Invetec Pro [pdf] Instructions
V4 FD Invetec Pro, V4, FD Invetec Pro, Invetec Pro, Pro

References

User Manual

Pandora V4 FD Invetec Pro

Product Usage Instructions

FAQ