NB-WPT-X5 Wireless Probe
“
Specifications:
- Model number: NB-WPT-X5
- Model name: Wireless Probe
- Touch Plate
- Receiver Specifications:
- Operating Voltage: DC5V-24V
- Operating Current: Average current 100mA, 30mA (typical)
- Wireless Range: 20 meters
- Maximum Supported Load: 24V / 500mA
- Transmitter Specifications:
- Operating Voltage: DC 2.4V-3.6V
- Battery Type: CR2032
- Operating Current: 20mA
- Probing Cycles per Full Battery: Approx. 3000 (varies with
battery condition) - Wireless Range: 20 meters
- Repeatability Accuracy: 0.02mm
Product Usage Instructions:
Part 1. Unboxing & Checking Package Contents:
1. Transmitter module
2. Receiving module
3. 200mm Cable A
4. 200mm Cable B
5. Double-sided tape
Part 2. Dimensions Information:
– Various dimensions and mounting details provided in the
manual.
Part 3. Specifications:
– Detailed technical specifications of the Wireless Probe.
Part 4. Installation and Connection:
Step 1. Preparation: Pull out the insulation
tab from the battery.
Step 2. Receiver Mounting Method: Secure the
receiver using magnets or double-sided adhesive tape.
Step 3. Connection Method 1: Connect Cable A to
the receiving module of the Z-probe tool.
Step 4. Connection Method 2: Connect Cable B to
the receiving module of the Z-probe tool.
Step 5. Testing: Ensure correct connection by
pressing the touch plate on the transmitter.
Part 5. Demonstration Tutorial:
– Instructions for Z Probe operation in GrblControl
(Gsender).
Frequently Asked Questions (FAQ):
Q: How do I know if the probe is connected correctly?
A: Manually press the touch plate on the
transmitter. If the transmitter’s indicator light turns on and the
receiver’s buzzer emits a beep sound simultaneously, it means the
probe is connected correctly and can function normally.
“`
User Manual
NB-WPT-X5 Wireless Probe
V2.0 Sep.2025
Contents
Welcome………………………………………………………………………………………………….1 Disclaimer………………………………………………………………………………………………..2 Part 1.Unboxing & Checking Package Contents………………………………………………….3 Part 2.Dimensions Information……………………………………………………………………..4 Part 3.Specifications…………………………………………………………………………………..5 Part 4.Installation and Connection…………………………………………………………………6 Part 5.Demonstration Tutorial………………………………………………………………………8 Part 6.Battery Replacement………………………………………………………………………..11 Battery Safety Instructions…………………………………………………………………………12 Compliance Information…………………………………………………………………………….13 FCC warning…………………………………………………………………………………………….14 IC warning……………………………………………………………………………………………….16
Welcome
Thank you for purchasingthe Wireless Probe Tool from NymoLabs. For technical support orreplacement, please email us at support@nymolabs.com. We’realways here to help. Facebook:@NymoLabs
Scan QR code tojoin the group
For detailed operatinginstructions, please visit our YouTube channel.
For more tutorials anddownloads, Please visit our official website
Scan the QR codeto watch the Wireless Probe Tool tutorial video.
01
Disclaimer
Before installing,setting up, andoperating this product, pleaseread this manual carefullyto ensure safe andproper use. This product is compatiblewith most desktop engraving machines on the market. Please familiarize yourself with the electrical specifications and usageprecautions before useto avoid potential hazards. Do not use this product in harsh environments such as high temperature, high humidity,excessive dust, orflammable and explosive conditions to prevent safety hazardsor performance abnormalities. This product is a wireless transmission device andmay be affectedby radio frequency interference(RFI). Especially in environments with long distances or metal obstructions,it is recommended touse it in open areaswith minimal interference to ensurestable signal transmission. The product contains abutton battery inside. Pleasekeep it properly, away from children. Do not swallow, as it maylead to serious injury or evendeath. The receiver supports aDC input voltage rangeof 5V to 24V. Do not connect powersources exceeding 24V toavoid circuit damage. Any damage resultingfrom improper power usageis not covered bythe warranty. It is recommended toperform a function testbefore each use: plugthe receiver into thecontroller host, press theTouch Plate on the transmittermanually; if the transmitter’sindicator light turns onand the receiver’s buzzersounds simultaneously, the Z-probetool is functioning normally andthe battery level issufficient. Any malfunction or damagecaused by unauthorized actionssuch as self-disassembly,modification, soldering, or connecting non-original accessories isnot covered by thewarranty. If the user does notuse, maintain, or storethe product as recommendedin this manual, any direct or indirect loss resulting therefrom-including butnot limited to productdamage, loss of functionality, or personal injury. The company shall not be held liablefor any such losses.
02
Part 1.Unboxing & Checking Package Contents
1.Transmitter module
2.Receiving module
3. 200mm Cable A
4. 200mm Cable B
5. Double-sided tape
6.User Manual 03
Part 2.Dimensions Information
19mm
28 39mm
40mm
60mm
40mm 04
25mm 45mm
38mm
18mm
4xM3 Mounting Screw Holes (For situations where you want to fix theTransmitter module in a specific location)
D12x5mm-M4 Strong magnet
Part 3.Specifications
Model number : NB-WPT-X5 Model name : Wireless Probe
Touch Plate
IN GND 12/24V
Receiver Specifications: Operating Voltage: DC5V-24V Operating Current: Averagecurrent 100mA, 30mA (typical) Wireless Range: 20 meters Maximum Supported Load: 24V /500mA
Transmitter Specifications: Operating Voltage:DC 2.4V-3.6V Battery Type: CR2032 Operating Current: 20mA Probing Cycles per FullBattery: Approx. 3000 (varies with battery condition) Wireless Range: 20 meters Repeatability Accuracy: 0.02mm
Transmit Indicator
Signal Indicator
Power Indicator
Pairing Indicator 05
Part 4.Installation and Connection
Step1.Preparation Pull out the insulation tabfrom the battery.
Pull out
Step3.Connection Method 1 (UsingNBS-6040 and NBX-5040 as Examples)
1.Insert one end of cableA into the port ofthe receiving module of the Z-probe toolin the correct direction.
Scan the QR code toview the official tutorial video for the WirelessProbe Tool.
Step 2. Receiver MountingMethod.
When securing the receiverof the Z-probe toolto the machine,you can attach itusing magnets,or stick itwith double-sided adhesive tape.
Double-sided tape
2.Connect the other end ofthe cable to the probe port.
06
Mounting Method 1
Mounting Method 2
Bottom magnet
Part 4.Installation and Connection
Step 4.Connection Method 2(Using Control Boards from Other Manufacturers as anExample) 1. Insert one end ofcable B into theport of the receiving
module of the Z-probe toolin the correct direction.
Step 5.Testing Whether the ProbeIs Connected Correctly
2. Connect the other endof the cable tothe control board. Control Boards from Other Manufacturers
IN GND 5-24V
Indicator light
Probe Port
Black Black Gray IN GND 5-24V
Note: The actual wiring sequence shouldfollow the probe interface pinout of your control board. Users must make adjustments based on their specific control board configuration. The probe interface voltagemust be within the rangeof 5-24V; exceeding this range maycause damage to the device!
Manually press the touch plate on the transmitter.
If the transmitter’s indicator light turns on andthe
receiver’s buzzer emits a”beep” sound simultaneously,
it means the probe isconnected correctly and can
function normally.
07
Part 5.Demonstration Tutorial
Instructions for Z ProbeOperation in GrblControl (Gsender) Edit the Z-probe toolsetting command: The triggeringheight of the Z-probetool has been testedand calibrated beforethe product leaves the factory, as shown in theimage below. Thetriggering height is 38.25mm. Pleaseset this value according to the marking on theactual tool you purchased.The value Z45.000 representsthe lift height of theZ-axis after probing, which can be adjustedaccording to your actualneeds.
Note: Please set theZ-probe tool height accordingto the actual marked height onthe probing tool.
Probe Tool height 38.25mm 08
Probe G code G21 G91 G38.2 Z-50 F50 G92 Z38.25
G1 G90 Z40.000 F200
G91 G38.2 Z-50.000 F20 G92 Z38.25
G1 G90 Z45.000 F200
Part 5.Demonstration Tutorial
Use GrblControl (Gsender) toset up the Z-probe tool setting commands. Click the[Gear] icon at the top right of the main screen, then click [Probe].The configuration window shownin the bottom-left imagewill appear.Clickthe [Z-Probe] label on the GrblControl (Gsender)interface, as shown inthe right image. Atthis point, the [StartProbe] button will begreyed out. You need totouch the Z-axis probingtool so that it can be detected. Oncerecognized, the icon willturn green and the [Start Probe] button will becomeactive, as shown in thelower right image. Clickthe [Start Probe] button,and the software will automatically lower the tooland calibrate the height.
Spindle
Set the height ofthe Z-probe tool according to theactual measured value.
Router Bit Z Probe
Material
Machine Table
Not Triggered Triggered
Note: During tool probing,align the tool as closeto the center of the probeas possible to ensurebetter accuracy and consistency.
09
Part 5.Demonstration Tutorial
Use Offline Controller toset up the Z-probe tool setting commands. Tap the [Z-Probe] icon inthe Offline Controller selection interface . The configuration window shownin the image below willappear.
Set the Z-probe toolprobing speed.
Set the Z-probe Heightaccording to the actual measured value. Set the retraction heightafter Z-probing is completed.
Start Z probe touching
Cancel
10
Part 6.Battery Replacement
1.Remove the three screws at the bottom ofthe transmitter (black round-head Phillips flat-tipself-tapping screws M3x8), and take out thebottom case.
2.Use an Allen wrench to remove the battery.
4.Place the bottom case backinto position and fastenit with the three screws.
3.Insert the battery intothe battery compartment with the concave side ofthe battery facing downward.
11
Battery Safety Instructions
1. Ensure the batteriesare installed correctly according to polarity (+and -). 2. Do not mix oldand new batteries, different brands or typesof batteries, such as alkaline, carbon-zinc, or rechargeable
batteries. 3. Remove and immediatelyrecycle or dispose ofbatteries from equipment notused for an extendedperiod of time according
to local regulations. 4. Always completelysecure the battery compartment,If the battery compartmentdoes not close securely, stop using the
product, remove the batteries,and keep them awayfrom children.
WARNING
INGESTION HAZARD: This product contains a buttoncell or coin battery. DEATH or serious injury can occur ifingested. A swallowed button cell orcoin battery can causeInternal Chemical Burns in as little as2 hours. KEEP new and used batteriesOUT OF REACH of CHILDREN Seek immediate medical attentionif a battery is suspectedto be swallowed or inserted inside anypart of the body.
12
Compliance Information
FCC Compliance Statement FCC ID: This device complies withPart 15 of theFCC Rules. Operation is subject tothe following two conditions:
This device may not cause harmful interference. This device must accept any interference received,including interference that may cause undesired operation.
UL4200A Compliance Statement This product complies with theUL 4200A safety standard, which applies to consumerelectronic products containing button or coin cell batteries.
Button Battery IngestionWarning WARNING: Keep batteriesout of reach of children.
If swallowed, button batteries can cause serious internal chemical burns withina short time and maylead to death. If swallowed, seek emergencymedical attention immediately. Do not induce vomiting. This product features achild-resistant battery compartment.
Child Safety Warning WARNING: This product contains small parts andmay pose a choking hazard.Not for children under3 years. 13
FCC Warning
This device complies with part15 of the FCC Rules.Operation is subject tothe following two conditions:(1) This device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found tocomply with the limits for a Class A digitaldevice, pursuant to part15 of the FCC Rules. These limits are designedto provide reasonable protectionagainst harmful interferencewhen the equipment is operated in a commercialenvironment. This equipment generates, uses, and canradiate radio frequencyenergy and, if not installed and used in accordance with the instruction manual,may cause harmful interference to radio communications. Operation of this equipmentin a residential areais likely to causeharmful interference in whichcase the user will berequired to correct the interference at his ownexpense.
Measures: Reorient or relocatethe receiving antenna. Increase the separation betweenthe equipment and receiver. Connect the equipment into anoutlet on a circuit different from thatto which the receiveris connected. Consult the dealer or anexperienced radio/TV technician forhelp.
14
FCC Warning
Note: The Grantee is notresponsible for any changesor modifications not expresslyapproved by the partyresponsible for compliance. such modifications could voidthe user’s authority to operate the equipment. The device has been evaluated to meet generalRF exposure requirement. Thedevice can beused in portableexposure condition without restriction.
15
IC Warning
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subjectto the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that maycause undesired operation of the device.
Cet appareil contient des metteurs/r cepteurs exempts de licence qui sont conformes aux normes CNR exemptes de licence d’Innovation, Sciences et D veloppement conomique Canada. Son fonctionnement est assujetti aux deuxconditions suivantes : (1) Cet appareil ne doit pas causer d’interf rences. (2) Cet appareil doit accepter toute interf rence, y compris celles qui peuventEntra ner un fonctionnement ind sirable de l’appareil.
The device has been evaluated to meetgeneral RF exposure requirement. Thedevice can be used in portable exposure condition without restriction. L’appareil a t valu pour r pondre aux exigences g n rales d’exposition aux RF.L’appareil peut tre utilis sans restriction dans des conditions d’exposition portables.
16
IC Warning
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subjectto the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that maycause undesired operation of the device.
Cet appareil contient des metteurs/r cepteurs exempts de licence qui sont conformes aux normes CNR exemptes de licence d’Innovation, Sciences et D veloppement conomique Canada. Son fonctionnement est assujetti aux deuxconditions suivantes : (1) Cet appareil ne doit pas causer d’interf rences. (2) Cet appareil doit accepter toute interf rence, y compris celles qui peuvent Entra ner un fonctionnement ind sirable de l’appareil.
The device has been evaluated to meetgeneral RF exposure requirement. To maintain compliance with RSS-102 – Radio Frequency (RF) Exposure guidelines, this equipment should be installedand operated with a minimum distance of20cm between the radiator and your body. Le dispositif de a t valu r pondre g n ral rf exposition exigence.pour maintenir laconformit avec les directives d’exposition du RSS-102-Radio Fr quence (RF). ce mat riel doit tre install et exploit une distance minimale de 20 cm entre leradiateur et votre corps.
17
support@nymolabs.com
Documents / Resources
 |
NymoLabs NB-WPT-X5 Wireless Probe [pdf] User Manual 2BRC2-NB-WPT-X5, 2BRC2NBWPTX5, NB-WPT-X5 Wireless Probe, NB-WPT-X5, NB-WPT-X5 Probe, Wireless Probe, Probe |