PATCHING PANDA BLAST DIY Module

 

Zambiri Zamalonda

Zofotokozera

• Gulu: Wapakati
• Zigawo: Zida zamagetsi zomwe zimasonkhanitsidwa kale, ndi zida zamagetsi zimafunikira kukhazikitsa
• Kukula: Control PCB ndi spacers (2x11mm, 1x10mm)
• Kagwiritsidwe: Msonkhano wapamwamba kwambiri wamagetsi

Malangizo Ogwiritsira Ntchito Zogulitsa

• Alekanitse mzere wam'mbali popotoza zolumikizira zakunja pogwiritsa ntchito pliers.
• Pezani ndikuyika zitsulo zachitsulo pa PCB yolamulira monga momwe mwalangizira.
• Chongani mayikidwe ndi solder voltage regulator, cholumikizira mphamvu, ndi zodulira.
• Lowani nawo ma PCB onse pogwiritsa ntchito zitsulo zachikazi ndi zachimuna, gulitsani, ndikuwonjezera zitsulo zachikazi 2 × 13.
• Chepetsa mwendo wa fader kuti musagwirizane ndi zitsulo zoyikidwa.
• Dulani mwendo wakumbali wa fader kuti mupewe mabwalo amfupi.
• Ikani ndikuteteza batani ndi polarity yoyenera.
• Solder hardware, kusiya mwendo umodzi wotsetsereka wosasunthika kuti usinthe.
• Tsimikizirani ma slider musanayambe kugulitsa komaliza.
• Gwirizanitsani ma PCB onse, atetezeni ndi zomangira, ndikuyika mini-PCB.
• Onani ku bukhu la ogwiritsa ntchito kuti mupeze malangizo owongolera.

FAQ

• Q: Kodi ndimapewa bwanji kuwonongeka kwa Electrostatic Discharge (ESD)?
  • A: Dzichepetseni musanagwire bolodi lozungulira pogwira chitsulo pamwamba kapena chinthu chokhazikika.
• Q: Kodi ndingasinthe ma slider nditatha kugulitsa?
  • A: Siyani imodzi mwamiyendo yapansi ya slider yopanda unsolder poyamba kuti zosintha zikhale zosavuta musanayambe kugulitsa komaliza.

Mawu Oyamba

GREEDE WAPAKATI

• Kuti mupange gawo lanu latsopano, tsatirani njira zomwe zaperekedwa patsamba lotsatirali.
• Kupanga module yanu ndikosavuta. Ngakhale kuti zida zonse zamagetsi zimasonkhanitsidwa kale, muyenera kukhazikitsa ndi kuteteza zida za hardware. Ndikofunikira kuwonetsetsa kuti zida zonse zamakina zalumikizidwa bwino ndikuyikidwa bwino musanagulitsidwe.
• Onetsetsani kuti mwayang'ananso momwe gawo lililonse likuyendera kuti muwonetsetse kuti zonse zayikidwa bwino.
• Tsatirani sitepe iliyonse mwadongosolo, ndipo gwirani zigawozo mosamala, popeza ndizitsulo zamakono zamakono.
• Chidziwitso pa Electrostatic Discharge (ESD):
• Electrostatic discharge (ESD) imachitika pamene magetsi osasunthika achulukana ndikutuluka, monga kugwedezeka pang'ono komwe mungamve mukakhudza chitseko chachitsulo. ESD imatha kuwononga zida zamagetsi zamagetsi. Kuteteza ma modules anu panthawi ya msonkhano:
• Dzichepetseni pogwira chitsulo pamwamba kapena chinthu chokhazikika musanagwire bolodi.

Kukonzekera Msonkhano

TSATANI MFUNDO IZI POMANGA ZIZINDIKIRO IZI

1. Konzani zigawozo kuti muyambe ntchito yosonkhanitsa, ndikulekanitsa pang'onopang'ono mzere wam'mbali mwa kupotoza zingwe zolumikizira zakunja pogwiritsa ntchito pulasitala.
2. Pezani zida zachitsulo: pali zitatu zonse-ziwiri zoyezera (2x11mm) ndi imodzi yoyezera (1x10mm).
3. Ikani spacers pa ulamuliro PCB monga momwe chithunzi. Gwiritsani ntchito zida zokulirapo (2x11mm) kulumikiza ma PCB onse ndi spacer yaying'ono (1x11mm) monga momwe zasonyezedwera pachithunzichi.
4. Onani chithunzi cha voltage regulator, kulunjika kwa cholumikizira mphamvu, ndi zodulira. Ngati zonse zili zolondola, pitilizani kuzigulitsa m'malo mwake.
5. Lowani nawo ma PCB onse pogwiritsa ntchito zitsulo zachikazi ndi zachimuna, ndikugulitsa.
   Kuphatikiza apo, solder 2 × 13 zitsulo zachikazi monga momwe tawonetsera pa chithunzi kumanja.
6. Chepetsa mwendo wam'mbali wa fader womwe udzayike pafupi ndi zitsulo zomwe zidayikidwapo kale kuti mupewe kukhudzana ndikupewa kuzungulira kwakanthawi. Onani chithunzi chotsatira kuti chiwongoleredwe.
7. Dulani mwendo wam'mbali wa fader womwe udzayike pafupi ndi zikhomo zomwe zidagulitsidwa kale kuti mupewe kukhudzana ndikupewa kuzungulira kwachidule. Onani chithunzi chotsatira kuti chiwongoleredwe.
8. Chithunzichi chikuwonetsa momwe mwendo wambali wa fader sukhudza mapepala ogulitsidwa.
9. Ikani batani, kuonetsetsa kuti polarity ndiyolondola. Gwirizanitsani! m'mphepete mwa batani kumanzere ndi mbali yomwe ikuwonetsedwa pachithunzichi.
   Ikani zida zonse ndikuteteza gululo ndi zomangira, koma osagulitsabe.
10. Solder hardware, kupatulapo imodzi mwa miyendo yapansi ya slider.
    Izi zipangitsa kukhala kosavuta kusintha ngati pakufunika.
11. Tsimikizirani kuti zotsetsereka zikuyenda bwino komanso kuti miyendo yawo ikugwira bwino PCB musanapitirize ndi soldering.
12. Gwirizanitsani ma PCB onse ndikuwateteza ndi zomangira. Ikani mini-PCB ndi mbali yolembedwa yayang'ana kumanzere.
    Mwamaliza, onani buku la ogwiritsa ntchito kuti mudziwe momwe mungasankhire gawoli.

Zolemba / Zothandizira

PATCHING PANDA BLAST DIY Module [pdf] Buku la Malangizo BLAST, BLAST DIY Module, DIY Module, Module

Maumboni

• Buku Logwiritsa Ntchito