NOTIFIER NRX-M711 Radio System Input-Output Module Instruction
GAWO ZONSE
- Module 1
- SMB500 kumbuyo bokosi 1
- Chivundikiro choyambirira 1
- Mabatire (Duracell Ultra 123 kapena Panasonic Industrial 123) 4
- Zomangira za bokosi lakumbuyo ndi mapulagi apakhoma 2
- Zomangira za ma module 2
- 3-pin terminal block 2
- 2-pin terminal block 1
- 47 k-ohm EOL resistor 2
- 18 k-ohm alarm resistor 1
- Malangizo oyika ma module 1
- SMB500 back box unsembe malangizo
Chithunzi 1: IO module + bokosi lakumbuyo lakunja miyeso
DESCRIPTION
NRX-M711 radio input-output module ndi batire yoyendetsedwa ndi RF chipangizo chopangidwa kuti chigwiritsidwe ntchito ndi chipata cha wailesi cha NRXI-GATE, chomwe chikuyenda panjira yoyatsira moto (pogwiritsa ntchito njira yolumikizirana yogwirizana). Ndi gawo lapawiri lomwe lili ndi kuthekera kolowera ndi kutulutsa kosiyana, kuphatikiza ndi transceiver ya RF yopanda zingwe ndipo imaperekedwa ndi bokosi lakumbuyo lopanda zingwe. Chipangizochi chimagwirizana ndi EN54-18 ndi EN54-25. Ikugwirizana ndi zofunikira za 2014/53/EU kuti zigwirizane ndi malangizo a RED
MFUNDO
- Wonjezerani Voltage: 3.3 V Direct Current max.
- Standby Pakali pano: 122 μA@ 3V (yomwe ili mumayendedwe wamba)
- Red LED Current Max: 2 mA
- Green LED Cur. Kutalika: 5.5mA
- Kulunzanitsanso Nthawi: 35s (nthawi yayitali mpaka kulumikizana kwanthawi zonse kwa RF kuchokera
- mphamvu ya chipangizo)
- Mabatire: 4 X Duracell Ultra123 kapena Panasonic Industrial 123
- Moyo wa Battery: Zaka 4 @ 25oC
- Mawayilesi pafupipafupi: 865-870 MHz. Kutalika kwa Channel: 250kHz
- Mphamvu ya RF: 14dBm (max)
- Kutalika: 500m (mtundu wa mpweya waulere)
- Chinyezi Chachibale: 5% mpaka 95% (osasunthika)
- Kukula kwa Waya Waya: 0.5 - 2.5 mm2
- Mulingo wa IP: IP20
Lowetsani gawo
- Mapeto a Mzere Wotsutsa: 47K
- Kuyang'anira Panopa: 34 μA wamba
Zotulutsa Module
- Mapeto a Mzere Wotsutsa: 47K
- Kuyang'anira Panopa: 60 μA wamba
- Relay Contacts: 2 A @ 30 VDC (resistive load)
Gawo Lopereka Mphamvu Zakunja
- Voltage: 30V DC Max. 8V DC mphindi.
- Supervision Fault Voltage: 7V DC wamba
KUYANG'ANIRA
Zida izi ndi ntchito iliyonse yogwirizana nazo ziyenera kukhazikitsidwa motsatira ma code ndi malamulo onse oyenera
Chithunzi 1 chimafotokoza kukula kwa bokosi lakumbuyo ndi chophimba.
Mtunda pakati pa zida zamawayilesi uyenera kukhala wosachepera 1m
Table 1 ikuwonetsa makonzedwe a wiring a module
Table 1: Malumikizidwe a Terminal
| POKWERERA | KUGWIRITSA NTCHITO / NTCHITO | |
|
1 |
Lowetsani gawo | |
| Kulowetsa -ve | ||
| 2 | Lowetsani +ve | |
| Module yotulutsa (Mode yoyang'aniridwa) | Module yotulutsa (njira yolumikizira) | |
| 3 | Zogwirizana ndi T8 | Relay NO (nthawi zambiri imatsegulidwa) |
| 4 | Kutsitsa +ve | Relay C (wamba) |
| 5 | Zogwirizana ndi T7 | Relay NC (nthawi zambiri imatsekedwa) |
| 6 | Kuyang'anira: kulumikizana ndi katundu -ve | Osagwiritsidwa ntchito |
| 7 | Kutulutsa PSU -ve | Osagwiritsidwa ntchito |
| 8 | Kuti mutulutse PSU +ve | Osagwiritsidwa ntchito |
Zolowetsa Module zimafunika 47K EOL kuti zigwire bwino ntchito.
Output Module imafuna 47K EOL pa katundu kuti agwire ntchito ya norma mumayendedwe oyang'aniridwa.
Ngati katunduyo ndi wocheperako (poyerekeza ndi EOL) a
mndandanda wa diode uyenera kuwonjezeredwa kuti uyang'anire bwino katundu (onani Chithunzi 2 cha diode polarity).
Chithunzi 2: Diode Polarity
Chithunzi 3: Kusintha Katundu Wothandizira
Chithunzi 4: Kumbuyo kwa Module yokhala ndi Battery Compartment ndi Cover
Chithunzi 5: Kutsogolo kwa Module yokhala ndi Kusintha kwa Maadiresi
CHENJEZO: Kusintha Katundu Wowonjezera
Onani Chithunzi 3. Kunyamula katundu kungayambitse kusintha kwa ma surges, zomwe zingawononge ma modules relay contacts (i). Kuti muteteze olumikizana nawo, lumikizani Voltage Wopondereza (iii) - mwachitsanzoample 1N6284CA - kudutsa katundu (ii) monga momwe tawonetsera pa Chithunzi 3. Kapenanso, pa ntchito zosayang'aniridwa za DC, ikani diode yokhala ndi reverse breakdown vol.tage wamkulu kuposa 10 kuwirikiza voltage. Chithunzi 4 mwatsatanetsatane kukhazikitsa batire ndi Chithunzi 5 malo adiresi masiwichi
Zofunika
Mabatire akuyenera kuyikidwa panthawi yoyimitsidwa chenjezo, chenjezo, chenjezo, chenjezo la wopanga mabatire kuti agwiritse ntchito komanso zomwe akufuna kuti atayike.
Ziwopsezo zophulika ngati mtundu wolakwika utagwiritsidwa ntchito Osasakaniza mabatire ochokera kwa opanga osiyanasiyana. Posintha mabatire, onse 4 adzafunika kusinthidwa Kugwiritsa ntchito mabatirewa kwa nthawi yayitali pa kutentha pansi -20 ° C kungachepetse moyo wa batri kwambiri (mpaka 30% kapena kuposa)
Kukonza gawoli: Chotsani zomangira ziwiri pachivundikiro chakutsogolo kuti muwulule gawo la RF. Chotsani gawo la RF m'bokosi lakumbuyo (onani pansipa). Lembani bokosi lakumbuyo kumalo omwe mukufuna pakhoma pogwiritsa ntchito zokonzera zomwe zaperekedwa. Bwezeraninso gawoli mubokosi (onani pansipa). Mawaya ma plug-in terminals monga momwe amafunira ndi dongosolo. Konzaninso chophimba chakutsogolo kuti muteteze gawo. Kuchotsa gawoli m'bokosi lakumbuyo: Chepetsani zomangira ziwiri, potozani moduli molunjika pang'ono ndikukweza. Sinthani ndondomekoyi kuti mukonzenso gawoli. Chenjezo Lochotsa Chipangizo: Pogwira ntchito, uthenga wochenjeza udzatumizidwa ku CIE kudzera pa Gateway pamene chivundikiro chakutsogolo chachotsedwa m'bokosi lakumbuyo.
KUKHALA Adilesi
Khazikitsani adilesi yozungulira potembenuza masiwichi awiri azaka khumi kutsogolo kwa gawoli pogwiritsa ntchito screwdriver kutembenuza mawilo ku adilesi yomwe mukufuna. Pokhapokha pamene Advanced Protocol (AP) ikugwiritsidwa ntchito (onani m'munsimu) module ya I / O iwiri idzatenga ma adiresi awiri a module pa loop; adiresi ya module yolowetsayo idzakhala nambala yomwe ikuwonetsedwa pa zosintha (N), adiresi yotulutsa gawo idzawonjezeka ndi imodzi (N + 1). Kotero kwa gulu lomwe lili ndi maadiresi 99, sankhani nambala pakati pa 01 ndi 98. Mu Advanced Protocol (AP) maadiresi mumtundu wa 01-159 alipo, malingana ndi mphamvu zamagulu (onani zolemba zamagulu kuti mudziwe zambiri pa izi).
ZIZINDIKIRO ZA LED
Module ya wailesi ili ndi chizindikiro cha LED chamitundu itatu chomwe chikuwonetsa momwe chipangizocho chilili (onani Gulu 2):
Gulu 2: Ma LED a Module Status
| Module Status | LED State | Tanthauzo |
| Kuyambitsa mphamvu (palibe vuto) | Long Green kugunda | Chipangizo sichinatumizidwe (chosakhazikika chafakitale) |
| 3 Kuthwanima kobiriwira | Chipangizo chatumizidwa | |
| Kulakwitsa | Blink Amber 1 iliyonse. | Chipangizo chili ndi vuto lamkati |
|
Osatumizidwa |
Wofiyira/Wobiriwira amaphethira kawiri ma 14s aliwonse (kapena Kubiriwira kokha polankhulana). | Chipangizo chili ndi mphamvu ndipo chikudikirira kukonzedwa. |
| Kulunzanitsa | Wobiriwira/Amber amaphethira kawiri ma 14s aliwonse (kapena Kubiriwira kokha polankhulana). | Chipangizo chili ndi mphamvu, chokonzedwa ndikuyesera kupeza/kujowina netiweki ya RF. |
| Wamba | Kulamulidwa ndi gulu; ikhoza kukhazikitsidwa ku Red ON, Green ON, nthawi ndi nthawi kuphethira kobiriwira kapena KUZIMA. | Kulumikizana kwa RF kumakhazikitsidwa; chipangizo chikugwira ntchito bwino. |
| Wopanda ntchito
(magetsi otsika) |
Amber/Green amaphethira kawiri ma 14s aliwonse | Network ya RF yotumizidwa ili mu standby; amagwiritsidwa ntchito pamene chipata chazimitsidwa. |
KUPANGITSA NDI KUCHITA Kukonzekera Module Yotulutsa
Module yotulutsa imaperekedwa kukonzedwa ngati Supervised Output Module (factory default setting). Kuti musinthe zotulutsa kuti zikhale zolumikizirana (Fomu C - olumikizana nawo opanda volt) pamafunika pulogalamu yosiyana pogwiritsa ntchito Device Direct Command in AgileIQ (Onani Radio Programming and Commissioning Manual - ref. D200- 306-00 kuti mumve zambiri.)
Kuyambira ndi gawo lomwe silinatumizidwe
- Chotsani ku bokosi lakumbuyo.
- Onetsetsani kuti adilesi yakhazikitsidwa ku 00 (zosakhazikika).
- Ikani mabatire.
- Sankhani tabu ya Device Direct Command mu AgileIQ.
- Dinani kawiri pa zenera kuwulula mndandanda wa options ndi kutsatira malangizo sintha linanena bungwe mode.
Zindikirani: Chotsani mabatire ku chipangizocho pambuyo pake ngati ntchito yotumiza dongosolo sikuyenera kuchitika. Ndikofunikira kuti kasinthidwe ka module yotuluka kuzindikirike kuti mudzagwiritse ntchito mtsogolo pa lebulo la module mutatha kutumiza:
Kutumiza
- Chotsani gawoli m'bokosi lakumbuyo.
- Onetsetsani kuti adilesi yolondola yakhazikitsidwa.
- Ikani mabatire.
- Konzaninso gawoli ndikusintha bokosi lakumbuyo lakutsogolo
chipata cha RF ndi gawo la RF pochita kukonza pogwiritsa ntchito chida cha pulogalamu ya AgileIQ. Pa nthawi yotumiza, ndi zida za netiweki za RF zoyatsidwa, chipata cha RF chidzalumikiza ndikuzipanga ndi chidziwitso cha netiweki ngati pakufunika. Ma module a RF ndiye amalumikizana ndi zida zake zina zomwe RF ma mesh network imapangidwa ndi Gateway. (Kuti mumve zambiri, onani Radio Programming and Commissioning
ZINDIKIRANI: Osayendetsa mawonekedwe opitilira USB amodzi nthawi imodzi kuti mutumize zida kumalo. ZINTHU ZONSE
Chithunzi 6: Zotuluka Module Yoyang'aniridwa
Chithunzi 7: Kulowetsa / Kutulutsa Module Relay Mode
Notifier Fire Systems wolemba Honeywell Pittway Tecnologica Srl Via Caboto 19/3 34147 TRIESTE, Italy
EN54-25: 2008 / AC: 2010 / AC: 2012 Zida Zogwiritsa Ntchito Maulalo a Wailesi EN54-18: 2005 / AC: 2007 Zida zolowetsa / zotulutsa kuti zigwiritsidwe ntchito pozindikira moto ndi ma alarm amoto anyumba
EU Declaration of Conformity Hereby, Notifier yolembedwa ndi Honeywell yalengeza kuti zida za wailesi zamtundu wa NRX-M711 zikutsatira malangizo a 2014/53/EU Mawu onse a EU DoC atha kufunsidwa kwa: HSFREDDoC@honeywell.com
Zolemba / Zothandizira
 |
NOTIFIER NRX-M711 Radio System Input-Output Module [pdf] Buku la Malangizo NRX-M711 Radio System Input-Output Module, NRX-M711, Radio System Input-Output Module, Input-output Module, Output Module, Module |
