nke WATTECO 50-70-124 Toran’O Atex zone 1 Puls Counting Sensor

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-PRODUCT

Recommendations for use

The use of accessories:
Installation, maintenance, and use must only be carried out by personnel who are competent in the use of electrical equipment in explosive atmospheres as defined in EN 60079-14. Any repair or modification is strictly prohibited without the written permission of Nke Watteco. Risk of electrostatic discharge: The user must implement any action to control the risks of electrostatic discharge, especially by cleaning the product only with a damp cloth.

USE ONLY SAFT-TYPE LS17500 BATTERIES.
Only the use of accessories in accordance with the intrinsic safety parameters is permitted.

Start

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-1

Provision the device on your LoRaWAN network with the keys available on the secure platform.

ONnke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-2

OFFnke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-3

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-4

https://www.watteco.fr/assistance/tutoriels-video/ 

Connectiques Connectors

 

Connecteur A : 4 points

Connector A: 4 points

Connecteur B : Rondelle rouge : 6 points

Connector B: Red circle:

6 points

Connecteur C : 6 points

Connector C: 6 points

Connecteur

Connector

Paramètres SI

IS parameters

Connecteur

Connector

Paramètres SI

IS parameters

Connecteur

Connector

Paramètres SI

IS parameters

4-20 mA 0-5V S0
Uo = 6,33V
 

 

 

Toran’O Atex Zone 1 IP55 : [50-70-124]

 

 

P1 : OUT – V+

[~14Vdc@20mA]

 

P2 : GND

Uo = 18,9V Io = 91mA

Po = 430 mW

 

Co = 1,6µF [IIB]

P1: OUT – V+ [~5,5Vdc@5mA] P2: GND

P3: IN-Measure 1

Uo = 6,51V Io = 67mA

Po = 108 mW

 

Co = 500µF[IIB],

P1: INPUT 1 P2: GND P3: INPUT 2 Io = 33µA Po = 23µW

Co = 650µF[IIB], Co = 28µF[IIC]

Lo = 1H [IIB],

IP68 : [50-70-150]  

P3 : IN-Measure

 

Co = 262nF [IIC]

 

P4: GND

 

Co = 22µF[IIC]

P4 : GND

 

P6: INPUT 3

Lo = 1H [IIC]

Ui = 25V

P4 : NC Lo = 17mH [IIB] Lo = 4mH [IIC] P6: IN-Measure 2

 

P7: GND

Lo = 33mH [IIB], Lo = 8mH [IIC]  

P7: GND

Ii = 450mA Ci = 3,3nF

Li ~ 0

Uo = 6,33V
P1: INPUT 1 Io = 33µA
 

P2: GND

Po = 23µW

Co = 650µF[IIB],

Pulse Sens’O Atex zone 1 P3: INPUT 2 Co = 28µF[IIC]
IP55  : [50-70-123]

IP68  : [50-70-152]

P4: GND

 

P6: INPUT 3

Lo = 1H [IIB], Lo = 1H [IIC]

Ui = 25V

P7: GND Ii = 450mA
Ci = 3,3nF
Li ~ 0

A, B, and C refer to the connectors in the table on the previous page

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-5

Output Signal:

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-7

Contact sec: Dry contact:

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-9

Sortie collecteur ouvert NPN Open collector output NPN

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-10

Compatible with a voltage of 3V and a current of 3uA.

NPN Open Collector:
Others, need to connect a compatible AtEx zone 1 external power supply with a resistor to limit the current. The below example is given with an external 12V power supply.

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-10

Marking

Pulse Sens’O sensors are certified according to the harmonized standards EN60079-0 ed. 6 and EN60079-11 ed.6 (EU Type Examination Certificate DEKRA20ATEX0017 X)

Pulse sens’O 

  • 0344 II 2 GD
  • Ex ib IIB, IIC T4 Gb
  • Ex ib IIIC T135°C Db -20 ≤ Tamb ≤ +50°C
  • DEKRA 20ATEX0017 X

WARNING: DO NOT CHANGE THE BATTERY IN AN EXPLOSIVE ATMOSPHERE – ONLY USE TYPE OF BATTERY SAFT LS17500 – POTENTIAL ELECTROSTATIC CHARGING HAZARD – INTRINSIC SAFETY PARAMETERS FOR CONNECTORS – SEE INSTRUCTIONS NKE WATTECO – RUE GUTENBERG – 56700 HENNEBONT – FRANCE

WARNING: DO NOT CHANGE THE BATTERY IN EXPLOSIVE ATMOSPHERE – ONLY USE TYPE OF BATTERY SAFT LS17500 – POTENTIAL ELECTROSTATIC CHARGING HAZARD – INTRINSIC SAFETY PARAMETERS FOR CONNECTORS – SEE INSTRUCTIONS NKE WATTECO – RUE GUTENBERG – 56700 HENNEBONT – FRANCE

Installation Setting up

Opening / Closure

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-11

Unscrew the 4 screws by ¼ turn

Montage mural Wall mounting

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-12

Place the dowels and screw the housing to the wall

Radio propagation

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-13

Check the radio coverage with the Netw’O.

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-14

For the sensor communicates correctly, the number of obstacles should be limited to avoid excessive radio attenuation.

Characteristics

Reference 50-70-124 50-70-150 50-70-123 50-70-152
Class A A
Power Level +14 dBm +14 dBm
Measures : Input S0

4-20mA / 0-5V

Input S0
Antenna Internal Internal
Casing materials ASA / PC ASA / PC
 

IP rating

 

IP55

 

IP68

 

IP55

 

IP68

SITE SUPPORT

nke-WATTECO-50-70-124-Toran’O-Atex-zone-1-Puls-Counting-Sensor-fig-15

https://support.watteco.com/

Documents / Resources

nke WATTECO 50-70-124 Toran’O Atex zone 1 Puls Counting Sensor [pdf] User Guide
50-70-124, 50-70-123, Toran O Atex zone 1 Puls Counting Sensor, Puls Counting Sensor, Counting Sensor, 50-70-124, Toran O Atex zone 1, Sensor
nke WATTECO 50-70-124 Toran'O Atex Zone 1 Puls Counting Sensor [pdf] User Guide
50-70-124 Toran O Atex Zone 1 Puls Counting Sensor, 50-70-124, Toran O Atex Zone 1 Puls Counting Sensor, Zone 1 Puls Counting Sensor, Puls Counting Sensor, Counting Sensor, Sensor

References

Leave a comment

Your email address will not be published. Required fields are marked *