NINGBO RF433M15 Remote Control WiFi Connection Network Logic

Specifications

Product	AT2688 Pendant Light
Features	WiFi Connection, Scene Modes, Color Adjustment

Remote Control WiFi Connection Network Logic and Function Description

1. Switch button 1 on the top left corner of the remote control, press and hold for 5 seconds within 30 seconds of powering on the product. Pairing: when paired successfully, the product will flash 2 cold white lights to indicate successful pairing. If the product is not paired within the specified time, please power it on again for pairing. After successfully pairing the remote control (default pairing below), press the button briefly to turn on/off the lights.
2. Press and hold the WiFi button 2 in the upper right corner of the remote control for at least 5 seconds to reset the product module’s networking. The product will enter the module’s networking mode and re-pair with the mobile app for networking.
3. Remote control 3 corresponds to a row of 1H, 4H, and 8H buttons. When the corresponding button is pressed, after the product is timed for 1 hour, 4 hours, and 8 hours respectively, the product will automatically turn off the lights.
4. The middle ring of remote control 4 corresponds to warm white light on the left side of Warm, and short press the color temperature (adjust the color temperature to warm white light by 10% once, and finally reach the warm white light color temperature). The Cool on the right side of the circular ring corresponds to the cool white light of the product, as well as the function of short pressing the color temperature (adjusting the color temperature of the cool white light by 10% corresponding to one press, and finally reaching the warm white light color temperature).
5. Press the button on the circular ring to increase the brightness of the product. Press once to increase the brightness by 10%, and finally reach 100% brightness. Press the button on the circular ring to lower the brightness of the product. Press once to lower the brightness of the corresponding product 10%, ultimately reaching a brightness of 10%.
6. The 5 Scene mode buttons in the middle of the circular ring switch product scene modes, corresponding to the mobile APP scene modes. Press once to switch one scene, for a total of 8 scenes.
7. Separate 6 rows of color buttons: Red, Green, Blue. Press the corresponding button to convert the product into the corresponding light.
8. Long strip with 7 color tones – hue, short press +/- button. The product switches back and forth from red light (- button lowest color) – green light – blue light to pink light (+ button highest color), with 10 colors.
9. Currently applicable product: AT2688 pendant light
   • (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Statement

Class B device:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

FAQ

• Q: What should I do if the device is causing interference?
  A: If you experience interference issues, try relocating the device to a different area. Ensure it is not placed near other electronic devices that may be causing the interference.
• Q: Can I modify the device in any way?
  A: No, any changes or modifications not approved by the responsible party may void your authority to operate the equipment. Consult a professional if modifications are necessary.

Documents / Resources

NINGBO RF433M15 Remote Control WiFi Connection Network Logic [pdf] User Manual 2BAT7RF433M15, rf433m15, RF433M15 Remote Control WiFi Connection Network Logic, RF433M15, Remote Control WiFi Connection Network Logic, WiFi Connection Network Logic, Network Logic, Logic

References

• User Manual