Next Level RACING NLR-S044 Flight Simulator Microsoft Flight Simulator Edition Instruction Manual

NLR-S044 Flight Simulator Microsoft Flight Simulator Edition

NEXT LEVEL RACING FLIGHT SIMULATOR
MICROSOFT FLIGHT SIMULATOR EDITION
INSTRUCTION MANUAL

chair

support@nextlevelracing.com 

YOUR FLIGHT JOURNEY STARTS HERE

We know you’re eager to start flying! Take your time with the instructions and follow this guide to assemble your product.  You’ll be setting yourself up for success by following the  instruction booklet to fully optimize your product.

qr-code

TAKE IT
TO THE SKIES
NEXTLEVELRACING.COM

support@nextlevelracing.com

PRE-FLIGHT CHECKS

WARNING & ASSEMBLY TIPS

  • Please do not use power tools for assembly as over tightening can damage your frame.
  • Lay out and build the cockpit on a level surface.
  • Do not force parts together.
  • Avoid cross threading bolts.
  • If in doubt consult the installation video.
  • Ensure all assembly fittings are properly tightened and periodically thereafter for safety and stability.
  • Moving parts present a pinch hazard. Take care when adjusting to avoid injury.
  • Do not use the seating if any part is broken, torn, or missing.

If you require any support with your product, please contact our friendly team at: support@nextlevelracing.com

WARNING CHOKING HAZARD – Small parts not for children under 3 years or any individuals who have a tendency to place inedible objects in their mouths.

video

NLR-S044 NEXT LEVEL RACING FLIGHT SIMULATOR
MICROSOFT FLIGHT SIMULATOR EDITION
NLR-S044 INSTRUCTIONS
Date of Document: May, 2025
Manufactured by:
Next Level Racing Simulations PTY LTD
23 Olympic CCT,
Southport, QLD 4215,
Australia

Video Instruction: bit.ly/nlrbuild

IN THE BOX: FRAME
*NOT TO SCALE
NOTE: Some Items Come with Rust Resistant Coating  

frame

support@nextlevelracing.com

support

Video Instruction: bit.ly/nlrbuild

IN THE BOX: SEAT *NOT TO SCALE

NOTE: Some Items Come with Rust Resistant Coating  

(R) (L)

parts

support@nextlevelracing.com

MOUNTING LOCATIONS
HOTAS PLATE  

PRODUCT LEGEND:

platePRODUCT LEGEND:

legendMOZA AB9 FFB HOTAS Base
TM HOTAS Warthog Stick / Winwing HOTAS Orion 2
Virpil Mongoos T-50CM2 Base
Virpil Mongoos T-50CM3 with WarBRD Base
Winwing Super Libra

Video Instruction: bit.ly/nlrbuild

FLIGHT PLATE  

scalePRODUCT LEGEND:

legend lightLogitech G X56 Throttle/HOTAS
Logitech G X52 Throttle/HOTAS
MOZA AB9 FFB HOTAS Base
MOZA MTP Throttle Panel-T00
TMT.16000M / TCA Sidestick Airbus
TM HOTAS Warthog Stick / Winwing HOTAS Orion 2
TM HOTAS Warthog Duel Throttle / Winwing Orion 2 Throttle
TM TCA Quadrant Airbus Edition Throttle
TM TCA Throttle Quadrant Boeing Edition
TM TWCS Throttle
Turtle Beach VelocityOne Flightstick
Virtual Fly TQ3+
Virtual Fly TQ6+
Virtual Fly V3RNIO+
VKB Gladiator NXT
VKB Gunfighter PRO MK.II
Virpil CDT-AEROMAX Flightstick
Virpil Mongoos T-50CM2 Base
Virpil Mongoos T-50CM3 with WarBRD Base
Virpil Universal Control Panel 1, 2 & 3
Virpil CDT-VMAX Throttle
Virpil Mongoos T-50CM3 Throttle
Virpil Rotor TCS Plus Base
Winwing Gemini Throttle Base

support@nextlevelracing.com

MOUSE PLATE  

mouse plate

PRODUCT LEGEND:

legend partsHoneycomb Bravo Throttle Quadrant
Logitech G X52 Throttle/HOTAS
Logitech G X56 Throttle/HOTAS
MOZA AB9 FFB HOTAS Base
MOZA MTP Throttle Panel-T00
TM 16000M / TCA Sidestick Airbus
TM HOTAS Warthog Stick / Winwing HOTAS Orion 2
TM HOTAS Warthog Duel Throttle / Winwing Orion 2 Throttle
TM TCA Quadrant Airbus Edition Throttle
TM TCA Quadrant Boeing Edition Throttle
TM TWCS Throttle
Turtle Beach VelocityOne Flightstick

NOT TO SCALE

fly dotVirtual Fly TQ3+
Virtual Fly TQ6+
Virtual Fly V3RNIO+
VKB Gladiator NXT
VKB Gunfighter PRO MK.II
Virpil CDT-AEROMAX Flightstick
Virpil CDT-VMAX Throttle
Virpil Mongoos T-50CM2 Base
Virpil Mongoos T-50CM3 with WarBRD Base Virpil Mongoos T-50CM3 Throttle
Virpil Universal Control Panel 1, 2 & 3  Virpil Rotor TCS Plus Base
Winwing Gemini Throttle Base
Video Instruction: bit.ly/nlrbuild

CENTRE YOLK FLIGHT PLATE

productPRODUCT LEGEND:

logitechLogitech G X56 Throttle/HOTAS
Logitech G X52 Throttle/HOTAS
MOZA AB9 FFB HOTAS Base
MOZA MTP Throttle Panel-T00
TMT.16000M / TCA Sidestick Airbus
TM HOTAS Warthog Stick / Winwing HOTAS Orion 2
TM HOTAS Warthog Duel Throttle / Winwing Orion 2 Throttle
TM TCA Quadrant Airbus Edition Throttle
TM TCA Throttle Quadrant Boeing Edition
TM TWCS Throttle
Virtual Fly TQ3+
Virtual Fly TQ6+
Virtual Fly V3RNIO+
Virtual Fly Yoko / Yoko+
Virpil Mongoos T-50CM2 Base
Virpil Mongoos T-50CM3 with WarBRD Base
Winwing Gemini Throttle Base

 

 

NOT TO SCALE support@nextlevelracing.com

COLLECTIVE BRACKET

brocket
NOT TO SCALE

PRODUCT LEGEND:

lightWinwing Gemini Collective
Virpil Collective with Bracket – Vertical Setup
Virpil Collective with Bracket – Horizontal Setup

Video Instruction: bit.ly/nlrbuild

ADJUSTMENT POINTS

The Flight Simulator is a fully adjustable cockpit making it perfect for flight enthusiasts of all sizes.
Utilize the various adjustment points to achieve the most
comfortable position.

adjust point

support@nextlevelracing.com

parts alig

PARTS:

1. AB)
• 1 x Rudder Frame
• 1 x Rudder Angle Plate
• 4 x M8 55mm Bolts
• 4 x Square Washers
• 4 x M8 Flange Nuts
A) Align the mounting holes on the Rudder Angle Plate with the slots on the Rudder Frame.
B) Bolt through and secure with 4 x M8 Bolts, Square Washers and Flange Nuts.  

PARTS:
• 1 x Rudder Plate
• 4 x M8 16mm Bolts
• 4 x M8 Washers

02 A) Align the mounting slots on the Rudder Plate with the threaded inserts on the Rudder Angle Plate.  B) Bolt through and secure with 4 x M8 Bolts and Washers.

PARTS:
• 2 x Seat Frames
• 2 x M8 55mm Bolts
• 2 x M8 16mm Bolts
• 4 x M8 Washers
• 2 x M8 Flange Nuts

A) Align the mounting holes on the Seat Frames with the mounting holes and threaded inserts on the Rudder Frame. 
B) On the top of the frame, bolt through and secure the Seat Frames with 2 x M8 16mm Bolts and Washers.
C) Bolt through the centre of the frame and secure with 2 x M8 55mm Bolts, Washers and Flange Nuts.

Video Instruction: bit.ly/nlrbuild

PARTS:
• 1 x End Plate
• 4 x M8 55mm Bolts
• 4 x M8 Washers
04 A) Align the threaded inserts on the End Plate with the mounting holes on the Left and Right Seat Frames. 
B) Bolt through and secure with 4 x M8 Bolts and Washers.

PARTS:
• 2 x Side Panels
• 4 x M8 55mm Bolts
• 4 x M8 Washers
• 4 x M8 Flange Nuts
05 Align the mounting holes on the Side Panels with the through holes on the Seat Frames. Bolt through  and secure with 4 x M8 Bolts, Washers and Flange Nuts.

PARTS:
• 1 x Cross Member
• 4 x M8 55mm Bolts
• 4 x M8 Washers
• 4 x M8 Flange Nuts
A) Align the mounting holes on the Cross Member with the through holes on the Left and Right Seat Frames and Side Panels.
B) Bolt through and secure with 4 x M8 Bolts, Washers and Flange Nuts.

support@nextlevelracing.com

OPTIONAL CROSS  MEMBER POSITION

NOTE: To lower your Flight Stick for the optional HOTAS assembly, see Step 16, you can use this position.  This adjustment also moves the stick further forward.  Additionally, in this position, the center pole support  bracket for the YOKE assembly will not connect.

PARTS:
• 1 x Cross Member (from Step 06)
• 4 x M8 55mm Bolts (from Step 06)

AB)07 A) Uninstall the hardware and Cross Member. 
• 4 x M8 Washers (from Step 06)
• 4 x M8 Flange Nuts (from Step 06)

B) Align the mounting holes on the Cross Member with the through holes on the Left and Right Seat Frames and Side Panels.

PARTS:

• 1 x Seat Backrest
• 1 x Seat Bottom
• 4 x M8 25mm Bolts
• 4 x M8 Washers

WARNING: Make sure both Seat Recliner Arms are set to the same angle before Side assembling the seat. If an adjustment is required use a cloth to protect your hand while adjusting. Remove warning labels once adjustment has been made.

A) Align the threaded inserts on the Seat Backrest with the mounting holes on the Seat Recliners.
B) Bolt through and secure with the M8 Bolts and Washers.

PARTS:
• 1 x Right Seat Recliner Cover 1 x Left Seat Recliner Cover
• 2 x M5 12mm Bolts
• 2 x Bolt Covers
A) Align the mounting hole on the Seat Recliner Covers with the Seat Recliners.
B) Bolt through and secure with the M5 Bolts and press fit the Bolt Covers to cover the hole.

SEAT RECLINER ADJUSTMENT

WARNING: The Seat Recliners  are spring loaded, take care when  adjusting to avoid injury.

Video Instruction: bit.ly/nlrbuild 

PARTS:

• NIL

Lift both Seat Recliner Levers to change the angle of the Seat Backrest. Release the levers adjusting 10 the backrest to lock in place.  

(4x Seat Mounting Locations)  

(Two Each Side of Seat Frames)

PARTS:

• 2 x M8 16mm Square Neck Bolts   (preinstalled to seat rails)

• 2 x M8 Nylon Lock Nuts

• 2 x M8 Washers (preinstalled to seat rails)

A) Remove Preinstalled Hardware and pull the Seat Slider handle up and adjust the Seat to the forward-most position. 
B) Align the mounting holes on the Seat Sliders with the seat mounting locations (Refer to image) on the Left and Right Seat Frames.
C) At the rear, bolt through and secure with 2 x M8 Square Neck Bolts, Nylon Lock Nuts and Washers.  

PARTS:

• 2 x M8 16mm Square Neck Bolts   (preinstalled to seat rails)

• 2 x M8 Nylon Lock Nuts

• 2 x M8 Washers  (preinstalled to seat rails)

A) Pull the Seat Slider handle up and adjust the Seat to the rear-most position.
B) At the front, bolt through and secure with 2 x M8 Square Neck Bolts, Nylon Lock Nuts and Washers.  

support@nextlevelracing.com

PARTS:

AB)L) R) • 2 x Side Arms

• 4 x M8 55mm Bolts

• 4 x M8 Washers

• 4 x M8 Flange Nuts

A) Align the mounting slots on the Left and Right Side Arms with the through holes on the Left and Right Seat Frames and Side Panels.
B) Bolt through and secure with 4 x M8 Bolts, Washers and Flange Nuts.

SIDE ARM ADJUSTMENT

PARTS:
• NIL

Loosen the Bolts to adjust the Side Arms to the desired height and angle. Tighten the Bolts to lock in place. Utilize the extra through holes on the Seat Frames for back and forward adjustment.  

NOTE: The plates are interchangeable and can be mounted to accommodate either left or right-handed users.

PARTS:

• 1 x Mouse Plate
• 1 x Flight Plate
• 8 x M8 Flange Nuts

Align the Threaded Studs on the Mouse Plate and Flight Plate with the mounting holes on the Left and Right Side Arms. Secure with 8 x M8 Flange Nuts.  

OPTIONAL HOTAS INSTALL (SKIP TO PAGE 24 FOR EXTENDED HOTAS SETUP)

Video Instruction: bit.ly/nlrbuild

PARTS:

• 1 x HOTAS Outer Pole

• 2 x M8 55mm Bolts

• 2 x M8 Washers

• 2 x M8 Flange Nuts

A) Align the mounting holes on the HOTAS Outer Pole with the through holes on the Cross Member. 
B) Bolt through and secure with 2 x M8 Bolts, Washers, and Flange Nuts.

PARTS:

• 1 x HOTAS Inner Pole
• 2 x 20mm Knobs
A) Align the threaded inserts on the HOTAS Inner Pole with the slot on the HOTAS Outer pole. 
B) Bolt through and secure with 2 x Knobs.

PARTS:

• 1 x HOTAS Plate
• 3 x M8 55mm Bolts
• 3 x M8 16mm Washers
• 3 x M8 Flange Nuts
A) Align the mounting holes on the HOTAS Plate with the through holes on the HOTAS Inner Pole. 
B) Bolt through and secure with 3 x M8 Bolts, Washers and Flange Nuts.

support@nextlevelracing.com

PARTS:
• 1 x Centre Outer Pole
• 2 x M8 55mm Bolts
• 2 x M8 Washers
• 2 x M8 Flange Nuts
• 1 x Barrel Spacer
A) Align the mounting holes on the Centre Outer Pole with the holes on the Rudder Frame.
B) Align the Barrel Spacer with the holes on the Centre Outer Pole. Bolt through and secure with 2 x M8 Bolts, Washers and  Flange Nuts.

Gently place the Centre Pole on top of the Rudder  Frame and make sure the latch is down.

Hook the U-Bolt into the locking tab on the  

Rudder Frame.  

NOTE: Periodically tighten the nuts.

Make sure the U bolt is sitting properly in the locking tab and pull the latch until its tight.

For a tighter lock, undo the latch, adjust the nuts  at the top of the latch and close it back again.

Video Instruction: bit.ly/nlrbuild

PARTS:
• 1 x Centre Inner Pole
• 2 x 20mm Knobs
• 1 x Felt Pad

A) Install 1 x Felt Pad onto the top of the Centre Inner Pole. Align the threaded inserts on the Centre Inner Pole with the slots on the Centre Outer Pole.
B) Bolt through and secure with 2 x Knobs.

CENTRE YOKE PLATE INSTALL

PARTS:
• 1 x Centre Yoke Plate
• 3 x M8 55mm Bolts
• 3 x M8 16mm Washers
• 3 x M8 Flange Nuts
A) Align the mounting holes on the Centre Yoke Plate with the through holes on the Centre Inner Pole.
B) Bolt through and secure with 3 x M8 55mm Bolts, Washers and Flange Nuts.

OPTIONAL TURTLE BEACH  

ADAPTOR INSTALL (Continue from Step 19a)

PARTS:
• 1 x Turtle Beach Adaptor Plate
• 2 x M6 20mm Press Fit Studs
• 2 x M6 Flange Nuts
A) Insert the 2 x M6 Studs into the rear-most holes on the Centre Yoke Plate.
B) Align the mounting holes on the Turtle Beach Adaptor Plate with the threaded studs, secure with 2 x M6 Flange Nuts.

support@nextlevelracing.com

YOKE/CLAMP PLATE INSTALL

Place the Clamp Plate on top of the Centre Inner Pole. 

PARTS:
• 1 x Clamp Plate
• 2 x M8 55mm Bolts
• 2 x M8 Washers
• 2 x M8 Flange Nuts

B) Slide the Clamp Plate forward and align the mounting holes on the Centre Inner Pole and Clamp Plate.
C) Bolt through and secure with 2 x M8 Bolts, Washers and Flange Nuts.

CENTRE KEYBOARD PLATE INSTALL 

PARTS:

• 1 x Keyboard Plate
• 2 x M8 55mm Bolts
• 2 x M8 Washers
• 2 x M8 Flange Nuts

A) Align the mounting holes and slots on the Keyboard Plate with the through holes on the Centre Inner Pole. 
B) Bolt through and secure with 2 x M8 Bolts, Washers and Flange Nuts.

Video Instruction: bit.ly/nlrbuild

PARTS:

• 6 x Adjustable Feet

A) Align the Adjustable Feet with the threaded inserts on the bottom of the Rudder Frame and Seat Frames. 
B) Lock into place by twisting the Adjustable feet into the threaded inserts. To raise an Adjustable Feet, twist anti-clockwise.  

PARTS:

• NIL

24 Your Flight Simulator cockpit is complete. 

OPTIONAL SUPPORT BRACKET INSTALL

PARTS:

• 1 x Support Bracket

• 1 x Support Bracket Mount

• 1 x M8 70mm Bolt

• 1 x Barrel Spacer

• 1 x M8 Washer

• 1 x M8 Flange Nut

25 Align the pivot point on the Support Bracket with the mounting holes on the Support Bracket Mount.  Bolt through and secure with 1 x M8 Bolt, Washer, Barrel Spacer and Flange Nut.  

support@nextlevelracing.com AB)

PARTS: • NIL

) Uninstall the Knobs securing the Centre Inner Pole to the Centre Outer Pole and remove the Centre Outer Pole.
B) Uninstall the 2 x M8 Flange Nuts securing the HOTAS Outer Pole to the Cross Member.

PARTS:

AB)

• 2 x M8 Flange Nuts

A) Align the mounting holes on the Support Bracket with the through holes on the Cross Member. 
B) Secure with 2 x M8 Flange Nuts previously uninstalled in Step 26.

PARTS:

• 1 x Centre Inner Pole

• 4 x 12mm Knobs

A) Align the threaded inserts on the Centre Outer Pole with the slots on the Support Bracket. Bolt through with 2 x Knobs.
B) Fit the Centre Inner Pole into the Centre Outer Pole. Align the threaded inserts on the Centre Inner Pole with the slot in the  Centre Outer Pole. Bolt through and secure with 2 x Knobs previously uninstalled in Step 26.

OPTIONAL KEYBOARD PLATE SIDE MOUNT

Video Instruction: bit.ly/nlrbuild

PARTS:

• 1 x Keyboard Arm

• 2 x M6 16mm Bolts

• 2 x M6 Washers

• 2 x M6 Flange Nuts

Align the mounting slots on the Keyboard Arm with the holes on the Mouse Plate. Bolt through and  secure with 2 x M6 Bolts, Washers and Flange Nuts.

PARTS:

• 1 x Keyboard Plate

• 2 x M8 55mm Bolts

• 2 x M8 Washers

• 2 x M8 Flange Nuts  

A) Align the mounting holes on the Keyboard Plate with the through holes on the Keyboard Arm. 
B) Bolt through and secure with 2 x M8 Bolts, Washers and Flange Nuts.  

OPTIONAL STRAIGHT SIDE ARM

PARTS:
• NIL

A) Uninstall 2 x M8 Bolts, Washers and Flange Nuts securing the Side Arm. Detach the Flight Plate from the Side Arm.
B) Uninstall 2 x M8 Bolts, Washers and Flange Nuts securing one side of the Cross Member to the Seat Frame.

support@nextlevelracing.com

AB)NOTE: The Straight Side Arm is interchangeable and works on both sides of the cockpit.

PARTS:
• 1 x Straight Side Arm
• 2 x M8 55mm Bolts
• 2 x M8 Washers
• 2 x M8 Flange Nuts
A) Align the Straight Side Arm with the through holes in the Seat Frame and Cross Member.
B) Bolt through and secure with 2 x M8 Bolts, Washers and Flange Nuts uninstalled in Step 31.

PARTS:

• 4 x M8 Flange Nuts

1 x Mouse Plate

A) Align the Mouse Plate Threaded Studs with the mounting holes on the Straight Side Arm. 
B) Secure with 4 x M8 Flange Nuts.

PEDAL PLATE ANGLE ADJUSTMENT

PARTS: • NIL

34 Uninstall the front Bolts, Square Washers and Flange Nuts securing the Rudder Angle Plate to the Rudder Frame and loosen the rear Bolts. Adjust to the desired angle. Bolt through and secure with the Bolts, Square Washers and Flange Nuts previously uninstalled.

HOTAS POLE HEIGHT ADJUSTMENT

Video Instruction: bit.ly/nlrbuild

PARTS:

• NIL

35 Loosen the Knobs securing the HOTAS Inner Pole to the HOTAS Outer Pole. Adjust to desired height  and tighten Knobs to lock in place.

HOTAS POLE ANGLE ADJUSTMENT

PARTS: • NIL

36 Uninstall the front Bolts, Washers and Flange Nuts securing the HOTAS Plate to the HOTAS Inner Pole. Angle to  the desired position. Bolt through and secure with 1 x Bolt, Washer and Flange Nut previously uninstalled.

CENTRE POLE HEIGHT ADJUSTMENT

PARTS: • NIL

37 Loosen the Knobs securing the Inner Centre Pole to the Outer Centre Pole. Adjust the Inner Centre Pole to the  desired height and tighten the Knobs to secure in place. Utilize the multiple threaded inserts for a perfect fit.  

support@nextlevelracing.com CENTRE PLATE ANGLE ADJUSTMENT

PARTS: • NIL

38 Uninstall the front Bolts, Washers and Flange Nuts securing the Centre Plate to the Inner Centre Pole. Angle to  the desired position. Bolt through and secure with 1 x Bolt, Washer and Flange Nut previously uninstalled.

TPR RUDDER INSTALLATION

39 Install 4 x M6 Threaded Studs into the TPR Adaptor. 

PARTS:

• 1 x TPR Adaptor

• 4 x M6 20mm Threaded Studs

PARTS:

• 2x M6 Flange Nuts

• TPR Rudder (not included)

A) Align the mounting holes on the front of the TPR Rudder with the Threaded Studs on the TPR Adaptor. 
B) Secure with 2 x M6 Flange Nuts. The TPR Rudders are ready to install onto the cockpit.  

EXTENDED HOTAS INSTALLATION

NOTE: To achieve the lowest Flight Stick position, install the extended HOTAS Bracket in the lower cross-member position as shown in Step 07.

Video Instruction: bit.ly/nlrbuild

PARTS:

• 1 x Extended HOTAS Bracket

• 2 x 55mm Sockethead Bolts

• 2 x M8 Washers

• 2 x M8 Flange Nuts

41 Align the mounting holes on the Extended HOTAS Bracket with the mounting holes on the cross  member. Bolt through and secure with 2 x M8 Bolts, Washers and Flange Nuts.

PARTS:

• 1 x HOTAS Plate

• 2 x 55mm Sockethead Bolts

• 2 x M8 Washers

• 2 x M8 Flange Nuts

42 Align the mounting holes on the HOTAS Plate with the mounting holes on the Extended HOTAS Bracket. Bolt  through and secure with 2 x M8 Bolts, Washers and Flange Nuts.

HOTAS BRACKET ANGLE ADJUSTMENT

PARTS: • NIL

43 Uninstall the front M8 Bolt, Washer and Flange Nut securing the HOTAS PLATE to the HOTAS Bracket. Adjust the  HOTAS Plate to the desired angle and re-install hardware to secure.

support@nextlevelracing.com

COLLECTIVE BRACKET INSTALLATION

PARTS:

• 1 x Collective Bracket

• 2 x 55mm Sockethead Bolts

• 2 x M8 Washers

• 2 x M8 Flange Nuts

44 Align the horizontal slots on the Collective Bracket with the mounting holes on the frame of the cockpit. Bolt  through and secure with 2 x M8 Bolts, Washers and Flange Nuts.

EXTENDED COLLECTIVE INSTALLATION  (RECOMMENDED FOR EXTENDED COLLECTIVES)

PARTS:

• 1 x Collective Bracket

• 2 x 55mm Sockethead Bolts

• 2 x M8 Washers

• 2 x M8 Flange Nuts

45 Align the horizontal slots on the Collective Bracket with the mounting holes on the frame of the cockpit. Bolt  through and secure with 2 x M8 Bolts, Washers and Flange Nuts.

COLLECTIVE BRACKET ADJUSTMENT

PARTS: • NIL

46 Loosen the bolts securing the Collective Bracket to the cockpit. Adjust to the desired position and tighten bolts to  secure.  

BUTTKICKER POLE INSTALL

Video Instruction: bit.ly/nlrbuild

PARTS:

• 1 x Buttkicker Pole

• 2 x M8 16mm Bolts

• 2 x M8 Washers

47 Align the mounting holes on the Buttkicker Pole with the threaded inserts under the Seat Bottom. Bolt through  and secure with 2 x M8 Bolts and Washers.

MOUSE MAT INSTALL

PARTS:

• 1 x Mouse Mat

48 A Mouse mat may be installed on top of the Flight or Mouse Plate. A mouse may now be used. 

KEYBOARD MAT INSTALL

PARTS:

• 1 x Keyboard Mat

49 Place the Keyboard Mat on top of the Keyboard Plate. A keyboard may now be used.  

support@nextlevelracing.com

NOTES

Documents / Resources

Next Level RACING NLR-S044 Flight Simulator Microsoft Flight Simulator Edition [pdf] Instruction Manual
NLR-S044, NLR-S044 Flight Simulator Microsoft Flight Simulator Edition, NLR-S044, Flight Simulator Microsoft Flight Simulator Edition, Simulator Microsoft Flight Simulator Edition, Microsoft Flight Simulator Edition, Flight Simulator Edition, Simulator Edition

References

Leave a comment

Your email address will not be published. Required fields are marked *