nedis IP camera
Description
- Status indicator
- Reset button
- Speaker
- Microphone
Use
- Download and install the app “Nedis SmartLife“ from
Apple App Store or Google Play Store on your mobile device. - Launch the app “Nedis SmartLife“.
- Create a new account or log in to your existing account.
- Tap “+” to add the device.
- Select “Security Camera” from the list of products.
- Connect the power adapter to the device. Insert the mains plug of the power adapter into the wall socket.
- If the status indicator does not flash: Press the reset button.
If the status indicator flashes: Confirm in the app. - Confirm the Wi-Fi network and password.
- Enter the device name.
Note: The device name will also be used for push notifications. - Use the metal bracket to mount the camera on the wall or in an angle.
- Place the camera on the bracket and rotate to fixate.
Safety
- To reduce risk of electric shock, this product should only be opened by an authorized technician when service is required.
- Disconnect the product from the mains and other equipment if a problem should occur.
- Read the manual carefully before use. Keep the manual for future reference.
- Only use the device for its intended purposes.
Do not use the device for other purposes than described in the manual. - Do not use the device if any part is damaged or defective. If the device is damaged or defective, replace the device immediately.
Cleaning and maintenance
- Do not use cleaning solvents or abrasives.
- Do not clean the inside of the device.
- Do not attempt to repair the device. If the device does not operate correctly, replace it with a new device.
- Clean the outside of the device using a soft, damp cloth.
Support
If you need further help or have comments or suggestions please visit www.nedis.com/support
Telephone: +31 (0)73-5993965
Email: service@nedis.com
Website: www.nedis.com/contact
NEDIS B.V.
De Tweeling 28
5215 MC ’s-Hertogenbosch
THE NETHERLANDS
Documents / Resources
 | IP camera |
References
- User Manualmanual.tools
Published: May 12, 2021
Updated: May 17, 2021
The user guide is nothing more than an installation guide, it should have setup settings, how to adjust recordings and other settings.
The user guide is nothing more than an installation guide, it should have setup settings, how to adjust recordings and other settings.
Käyttöoppaassa ei ole muuta kuin asennusohje, siinä pitäisi olla käyttöönotto asetukset, miten säädetään tallennukset ja muut asetukset.
The user guide is nothing more than an installation guide, it should have setup settings, how to adjust recordings and other settings.
The user guide is nothing more than an installation guide, it should have setup settings, how to adjust recordings and other settings.<e/em>
Käyttöoppaassa ei ole muuta kuin asennusohje, siinä pitäisi olla käyttöönotto asetukset, miten säädetään tallennukset ja muut asetukset.
The user guide is nothing more than an installation guide, it should have setup settings, how to adjust recordings and other settings.
Where can I find the setup settings, recording adjustments, and other advanced configurations for the Nedis IP camera?
The manual provided for the Nedis WIFICO20CWT Outdoor IP camera is indeed a Quick Start Guide focused on physical installation and initial app pairing. For advanced setup, recording adjustments, and other settings, you must use the Nedis SmartLife app.
Once the camera is successfully added to the app (following steps 1-9 in the manual), you can manage these features as follows:
If you require a more comprehensive digital manual or specific firmware help, Nedis recommends visiting their support page at www.nedis.com/support or contacting them at
service@nedis.com.Read the full Q&A page
How do you connect via onvif?
What is the user’s name?
etc. Michael
Hvorledes forbinder man via onvif?
Hvad hedder brugeren?
mvh Michael
What is the user's name?
etc. Michael<e/em>
Hvorledes forbinder man via onvif?
Hvad hedder brugeren?
mvh Michael
How do I connect the Nedis IP camera via ONVIF and what is the default username?
The provided manual for the Nedis WIFICO20CWT Outdoor IP camera focuses on setup via the Nedis SmartLife app and does not explicitly list ONVIF configuration steps or default local credentials.
Generally, for Nedis SmartLife cameras that support ONVIF, you must first complete the initial setup using the mobile app. Once the camera is connected to your network, you can often enable ONVIF features within the camera's settings menu in the app. Common default credentials for many Nedis/Tuya-based cameras are:
If you cannot find these settings in the app, please check the specific product page for your model at www.nedis.com/support as ONVIF support varies by specific hardware version.
Read the full Q&A page