nedap UNIT SD02 RF Smart Deactivator
IN THE BOX
Intended use
The Smart Deactivator model: SMART DEACT is an Electronic Article Surveillance (EAS) system intended to be used in stores at check-out counters for deactivating 8.2MHz anti-theft alarm tags.
Warning
This equipment should be installed, operated, serviced, and repaired by skilled personnel only. The installation and interconnection of this equipment to facility wiring and other equipment must be done by a competent, skilled craftsperson who is familiar with applicable standards and codes governing the installation. Installation methods, practices or procedures that are unauthorized or done improperly are dangerous and could result in serious personal injury or damage to property and equipment.
dimensions
Nedap N.V.
Parallelweg 2, NL-7141 DC Groenlo (The Netherlands) Mail: support-retail@nedap.com
Copyright © Nedap N.V. No part of this document may be reproduced, copied or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of Nedap N.V.
connect deactivator antenna cable to antenna connector
- Antenna wire red
- Antenna wire black
- To deactivator antenna
- Fix cable with tie-wrap
- Screw (2x)
connect to power 100-240V
- Power supply
- Lamp green on
- 2-pole Connector from power supply
- Volume button
beeper sound (standard sound)
connector explanation
program switch settings
connectors from smart deactivator
Status LEDs
- Green = Power
- Red = Label detected – 1 flash (Standard mode) Label deactivated – 3 flashes (Standard mode)
- Yellow = Output LED
- Orange = Status LED
Depending on dipswitch settings, LED behaviour can be different. (See settings below)
settings only for use with iSense (Version: > V7.6)
Renos RS485 | Smart deactivator RS485 | |
+12V | è | + |
A | è | B |
B | è | A |
GND | è | – |
Use shielded four-wire cable (e.g. Unitronic LiYCY 4×0,25 for a maximum length of 25m, or LiYCY 4×0,50 for maximum length of 50m)
Disclaimer
Nedap intends to make this manual accurate and complete. However, Nedap does not warrant that the information contained herein covers all details, conditions or variations, nor does it
provide for every possible contingency in connection with the installation or use of this product. Nedap disclaims any liability for damage to property or personal injury resulting, in whole or
in part, from improper installation, modification, use or misuse of its products. The information contained in this document is subject to change without notice.
FCC and ISED Compliance statement
This device complies with part 15 of the FCC Rules and this device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC and IC Radiation Exposure Statement
This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Information to the user
Note: This equipment has been tested and found to comply with the limits for a class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequent energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determine by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver.
NOTE: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To ensure compliance with FCC regulations, use only the shielded interface cables provided with the product, or additional specified components or accessories that can be used with the installation of the product. FCC ID: CGDSMART DEACT
IC:1444A-SMARTDEACT
CE Declaration of Conformity
Hereby, Nedap N.V. declares that the radio equipment model SMART DEACT is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://portal.nedapretail.com/
Singapore Compliance
Disposal of this product
The owner or last user of this product is responsible for proper disposal of (parts of) the product as required by local rules and regulations.
User manual
The complete instruction manual can be found at https://portal.nedapretail.com/
ISED Information to the user
This radio transmitter [1444A-SMARTDEACT] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
The following antenna models can be installed/connected to the Smart Deactivator.
- SDA-265×265
- DAPL 275×275
- MG9800I
- NCR7878-5000
- HN24-000002
Specifications
Power Supply | 100-240Vac Power adapter, 0.6-0.3A, 50-60Hz 12Vdc, 2A, 24W max. |
Dimensions | 185mm x 106mm x 37mm |
Weight | 800gr |
Output Power (8.2MHz) | Max 9 dBµA/m @ 10m |
Frequency Band (8.2MHz) | 7.4 – 8.8MHz |
Modulation | Frequency Sweep |
Antenna type | Inductive loop |
Documents / Resources
![]() |
nedap UNIT SD02 RF Smart Deactivator [pdf] User Manual SMARTDEACT, CGDSMARTDEACT, UNIT SD02 RF, Smart Deactivator, Deactivator, Deactivator Device |