Home - Nedap Retail Portal
User Manual for nedap models including: SMARTDEACT, CGDSMARTDEACT, UNIT SD02 RF, Smart Deactivator, Deactivator, Deactivator Device
Nedap N. V. SMARTDEACT Anti-Pilferage Device CGDSMARTDEACT CGDSMARTDEACT smartdeact
File Info : application/pdf, 8 Pages, 2.09MB
DocumentDocumentUNIT SD02 RF
1x | smart deactivator
1x | 4-pole antenna connector 1x | connector housing
1x | power supply (incl. adapters EU, UK, CN, US)
1x | cover
Intended use
The Smart Deactivator model: SMART DEACT is an Electronic Article Surveillance (EAS) system intended to be used in stores at check-out counters for deactivating 8.2MHz anti-theft alarm tags.
Warning
This equipment should be installed, operated, serviced, and repaired by skilled personnel only. The installation and interconnection of this equipment to facility wiring and other equipment must be done by a competent, skilled craftsperson who is familiar with applicable standards and codes governing the installation. Installation methods, practices or procedures that are unauthorized or done improperly are dangerous and could result in serious personal injury or damage to property and equipment.
dimensions
185 131,6
106 86,6 5 6
14,5 5 6 8 0
4,5
110
50
Quick ref. : UNIT SD02 RF
Nedap N.V. Parallelweg 2, NL-7141 DC Groenlo (The Netherlands) Mail: support-retail@nedap.com
dsgn date item
Copyright © Nedap N.V. No part of this document may be reproduced, copied or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of Nedap N.V.
: CvdB : 17 March 2020 9:06 am : 9200002
document : T9200002-45.01 revision : B.08
connect deactivator antenna cable to antenna connector
55 3
4
1
Antenna wire red
2
Antenna wire black
3
To deactivator antenna
4
Fix cable with tie-wrap
5
Screw (2x)
connect to power 100-240V
1 2
2 4
3
1
1
Power supply
2
Lamp green on
3
2-pole Connector from power supply
4
Volume button
beeper sound (standard sound)
deactivation detection
connector explanation
GND +12V
LED + LED -
Power connector Ground Power connector +12VDC
Voltage ripple <125mV
Led output connector + The led will flash 3x at deactivation
Led output connector -
and once on detection.
Out C Out NO
Output Common Normal open
Solid state output (max 120mA)
Inp A Inp K
Input anode Input Kathode
0 - 12V High signal, input >2V
+12V RS485 A RS485 B GND
+ RS485 connector A RS485 connector B -
It is possible, by using a special RS485 converter and software, to adjust some settings.
solid state output
G3VM-351A
OC1
c
no
Input
kathode (-)
anode (+)
GND
program switch settings
1
Standard mode
1 2 3 4 5 6 7 8
Led Yellow Led Orange
Low after deactivation High at input signal
2
1 2 3 4 5 6 7 8
3*
1 2 3 4 5 6 7 8
Line Termination RS485 Detect only mode
4
1 2 3 4 5 6 7 8
5*
1 2 3 4 5 6 7 8
Output
after 10 seconds of detection
Forced deactivation, for 90 seconds after input signal 90 seconds
6
Input used as switch for buzzer volume
1 2 3 4 5 6 7 8
7
1 2 3 4 5 6 7 8
8* 1 2 3 4 5 6 7 8
9*
1 2 3 4 5 6 7 8
Counting output inverted - Standard mode Detect only - Output inverted Deactivation only if input is high
10
1 2 3 4 5 6 7 8
High Low
= =
Low sensitivity Standard sensitivity
Led yellow Led orange
Led yellow Led orange
Led yellow Led orange
Led yellow Led orange
Led yellow Led orange
Led yellow Led orange
Led yellow Led orange
Low after detection Flash
High after 10 seconds detection Not used
High after 10 seconds detection High during deactivation
Low after deactivation High at input signal
High pulse after deactivation Not used
High pulse after detection Flash
High pulse after detection High during deactivation
11
Remote operation address 1
1 2 3 4 5 6 7 8
12
1 2 3 4 5 6 7 8
Remote operation address 2 Version: > V7.5
DLL mode - Transaction Controlling 4 = high address 2 4 = low address 1 (standard)
Forced deactivation, for 90 seconds after input signal
13
Output after 1 deactivation burst and still detection.
1 2 3 4 5 6 7 8
Input
90 seconds
Deactivation
14
Forced deactivation, for 90 seconds after input signal Output after 2 deactivation bursts and still detection.
1 2 3 4 5 6 7 8
Input
90 seconds
Deactivation
Led yellow Led orange
High after detection High during deactivation
Beeper default off.
Led yellow Led orange
High after detection High during deactivation
Beeper default off.
Forced deactivation, for 90 seconds after input signal
15
Output after 3 deactivation bursts and still detection.
1 2 3 4 5 6 7 8
Input
90 seconds
Deactivation
Led yellow Led orange
High after detection High during deactivation
Beeper default off.
* In detect only mode, due to the RF detection field, we cannot guarantee labels will never deactivate.
connectors from smart deactivator
Antenna connector side
Connector side
1 2 3 4 5 6 7 8
Status LEDs
Status LEDs
Green Red
= Power = Label detected 1 flash (Standard mode)
Label deactivated 3 flashes (Standard mode)
Yellow
= Output LED
Orange
= Status LED
Depending on dipswitch settings, LED behaviour can be different. (See settings below)
settings only for use with iSense (Version: > V7.6)
16
1 2 3 4 5 6 7 8
1 = Line Termination RS485 4 = Low Address 1
Shielding
Shielding
Renos electronics
Renos
Smart deactivator
RS485
RS485
+12V
+
A
B
B
A
GND
-
17
1 2 3 4 5 6 7 8
1 = Line Termination RS485 4 = High Address 2
Shielding
Shielding Shielding
Shielding
Renos electronics
Use shielded four-wire cable (e.g. Unitronic LiYCY 4x0,25 for a maximum length of 25m, or LiYCY 4x0,50 for maximum length of 50m)
Disclaimer
Nedap intends to make this manual accurate and complete. However, Nedap does not warrant that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. Nedap disclaims any liability for damage to property or personal injury resulting, in whole or in part, from improper installation, modification, use or misuse of its products. The information contained in this document is subject to change without notice.
FCC and ISED Compliance statement
This device complies with part 15 of the FCC Rules and this device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Cet appareil contient des émetteurs / récepteurs exempt (s) de licence qui sont conformes aux RSS(s) exemptes de licence d'Innovation, Sciences et Développement économique Canada. L'opération est soumis aux deux conditions suivantes: (1) cet appareil ne doit causer aucune interférence, et (2) cet appareil doit accepter n'importe quelle interférence, y inclus interférence qui peut causer une opération non pas voulu de cet appareil. Les changements ou modifications n'ayant pas été expressément approuvés par la partie responsable de la conformité peuvent faire perdre à l'utilisateur l'autorisation de faire fonctionner le matériel.
FCC and IC Radiation Exposure Statement
This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme a CNR-102 limites énoncées pour un environne- ment non contrôlé.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de Classe B est conforme à la norme Canadienne ICES-003.
FCC Information to the user
Note: This equipment has been tested and found to comply with the limits for a class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequent energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determine by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver. NOTE: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To ensure compliance with FCC regulations, use only the shielded interface cables provided with the product, or additional specified components or accessories that can be used with the installation of the product. FCC ID: CGDSMART DEACT IC:1444A-SMARTDEACT
CE Declaration of Conformity
Hereby, Nedap N.V. declares that the radio equipment model SMART DEACT is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://portal.nedapretail.com/
Este producto tiene certificado de homologación IFT número: RCPNESM19-0026
Singapore Compliance
Complies with IMDA Standards
DA105282
Disposal of this product
The owner or last user of this product is responsible for proper disposal of (parts of) the product as required by local rules and regulations.
User manual
The complete instruction manual can be found at https://portal.nedapretail.com/
ISED Information to the user
This radio transmitter [1444A-SMARTDEACT] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Cet émetteur radio [1444A-SMARTDEACT] a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous, avec le gain maximal autorisé indiqué. Les types d'antenne non inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour tout type répertorié sont strictement interdits pour l'utilisation avec cet appareil.
The following antenna models can be installed/connected to the Smart Deactivator.
1.
SDA-265x265
2.
DAPL 275x275
3.
MG9800I
4.
NCR7878-5000
5.
HN24-000002
Specifications
Power Supply
Dimensions Weight Output Power (8.2MHz) Frequency Band (8.2MHz) Modulation Antenna type
100-240Vac Power adapter, 0.6-0.3A, 50-60Hz 12Vdc, 2A, 24W max. 185mm x 106mm x 37mm 800gr Max 9 dBµA/m @ 10m 7.4 8.8MHz Frequency Sweep Inductive loop