MUNBYN IPDA086 Pro Android Barcode Scanner
Packing Open and Installation
What’s in the Box
| l | Charger |
| 2 | USBCable |
| 3 | Lanyard |
| 4 | Protective Film |
| 5 | Device |
| 6 | MUNBYN Manual |
| 7 | Pistol (Optional) |
| 8 | Silicone Case |
| 9 | Hand Strap (Optional) |
User Manual & SOK Download
You can download the user manual and SOK for IPDA086 Pro by following the link below or scanning the QR code: https://munbyn.biz/lPDA086Pro
Appearance
| Button | Description | |
|
Side button |
1 Power | Locate on the right side, press to ON/OFF device |
| 2
PTT key |
Locate on the right side, its
function can be defined by the software |
|
| 3
SCAN |
Scanning button is located on both sides. There are two scanning buttons | |
| 4
Volume+/- |
Volume up and down | |
Install the Battery, SIM card, and SD card
- Place the NANO SIM card or Micro SD Card into the tray as shown.
- Note: Please remove the battery when the power is off.
- Please remove the battery insulation sticker before first use, otherwise it will not turn on.
Install the NANO SIM or TF in the direction shown in the icon.
TIP: Install the SIM card/ TF card after shutting down the device.
InfoWedge Settings
InfoWedge 
is a mobile device data capture software that easily captures, processes, and transmits scan data. It easily integrates this data with the customer’s existing applications, reducing the need for additional programming or modification of application code.
Basic Settings
Enable InfoWedge
Make sure Infowedge is enabled before using the scanner. Generally, Infowedge is enabled by default to ensure that you can use it out of the box.
- First, open Infowedge and click on the menu in the upper-right corner.
- Click Settings.
Confirm Infowedge is enabled.
NOTE: You can also reset lnfowedge to its initial state from this page.
For example, if the scanning laser does not light up when you press the scan button, you can try clicking “Restore” to restore factory settings.
Using the Profiles
lnfoWedge functionality is based on profiles containing a group of scan-related settings.
lnfoWedge includes two preset profiles to support common or specific needs.
- Profile: The default profile. It will automatically take effect for any application that has not been associated with an lnfoWedge profile. Usually, we can change the scan settings in this profile.
- Launcher: The profile is used when the device is on the home screen. This is enabled by default. If you disable it, you will not be able to use the scanner on the home screen.
Barcode Input Settings
Click “ProfileO (Default)” to set the default profile. If you do not create a new profile and associate it with an application, the scan settings of “ProfileO (Default)” will take effect for all applications.
- Profile enabled: The profile is enabled by default.
- Scanner enabled: The scanner is enabled by default.
- Success audio prompt: Select the scanning success prompt tone.
- Failure audio prompt: Enable or disable the scan failure prompt sound.
- Vibrate prompt: Enable or disable the scanning vibration prompt.
- Key Trigger: Select the key trigger method.
- Character Set: Character set selection, is automatically selected by default.
Configure scanner settings: Used to configure scanner-related parameters- Decoders: Common barcode settings. You can enable or disable a barcode .
Tips
- If a barcode cannot be scanned, you need to check if that type of barcode is enabled.
- If you are experiencing missing numbers or characters after scanning a barcode, you can click on that barcode type to enable the Transmit Check Digit setting. An example is the UPC barcode:
Barcode Processing Settings
After scanning the barcode data, lnfoWedge can process the data and output it according to the requirements. The data can be processed in the following three ways:
GSl Formatting
GSl barcode formatting: mainly for the processing of GSl type barcodes, such as splitting barcodes, deleting GS characters, etc.
The following table shows examples of GSl barcode format settings:
 |
|
| Original barcode data | 0104900001802281172404271019179878 301 |
| Delete GS | 0104900001802281172404271019179878301 |
| Remove GS+
separate decoding |
(01)04900001802281(17)240427(10)19179878(30)1 |
| Delete GS+ singl e decoding | (01)04900001802281
(17)240427 |
| + single line break | (10)19179878 |
| (30)1 | |
| Replace the GS character with (GS] | 0104900001802281172404271019179878(GS]301 |
Basic Data Formatting
Basic Data Formatting: perform simple processing operations on the data, such as adding prefixes and suffixes, deleting characters, etc.
- Data Prefix: Adds a number or character in front of the barcode data.
- For example: input “ABC”, the original barcode is “12345”, then the final output is “ABC12345”.
- Data Suffix: Adds numbers or characters after the barcode data.
- For example: if you input “ABC” and the original barcode is “12345”, the final output will be “l2345ABC”.
- Send ENTER key: Enable this setting and the output will wrap automatically. (Enabled by default)
- Send TAB key: The read data will be suffixed with a tab character “\t”. When reading data in Excel, the cursor will automatically move to the next cell.
- Delete starting characters: Enter the number of characters to delete from the beginning.
- Delete trailing characters: Enter the number of characters to delete from the end.
- Delete specified string: It will delete the characters you entered.
Advanced Data Formatting
Advanced data formatting: You can perform programming-like operations on data: select some predetermined rules and process the data in sequence.
Enable advanced data formatting
By default, there is a preset rule: Rule0, which does not process the barcode in any way. You can click the”+” sign to create multiple rules.
Rule triggering conditions
You can trigger the next action of this rule by specifying a string, a barcode data position, a length, or a barcode type.
Perform an action
Click the”+” sign to select the next action that this rule can perform. You can add multiple actions to meet some complex requirements.
Data Output Mode Settings
Keystroke Output
Keystroke Output is the default scanning output mode enabled by lnfowedge. By default, when you scan a barcode, the data will be output at the cursor position.
You have three key output options:
• Append on cursor: After scanning the barcode, the data will be immediately displayed where the cursor is.
• Simulate keystroke: The barcode data will be output in simulated keyboard input mode.
• Replace on cursor: Replace the data at the cursor position with the barcode data.
Intent Output
Intent output uses Android’s broadcast mechanism to transmit barcode data to the user’s APP. Default off.
IP Output
PDA outputs barcode data to the target IP host via TCP/UDP protocol. Default off.
Note: PDA must be in the same network segment as the target host.
Clipboard Output
The barcode data scanned by the PDA will be saved in the clipboard. Default off.
New Profile
With lnfoWedge, you can create a profile and link it to your app.
You can achieve:
- Create multiple profiles and associate different applications so that different applications can process the same scan data in different ways.
- Create a single profile and associate it with multiple applications to acquire and process scan data in the same way.
Note: A profile can be associated with one or more pages or apps, but a page or app can only be associated with one profile.
New Profile
- Click the menu in the upper right corner and select > New Profile.
- Enter the name of the Profile in the pop-up input box and click OK.
3. Finish creating the Test profile
Associated APP
- Select the profile you created.
- On the configuration page, click Associate App to start associating the app.
- Tap the menu in the upper right corner and select > New App/Activity. A list will appear containing all the apps installed on your device.
4.For example, you can associate a profile with Odoo. When you select the”*” symbol, all active pages in Odoo will be associated. You can also select a specific page to associate with. 
Inventory Management Software
This device is compatible with a large number of inventory management software on the market. This section will briefly describe three inventory management software programs. You can download the following three inventory management applications from the Google Play Store.
Odoo
Odoo is an open-source enterprise resource planning (ERP) and customer relationship management (CRM) system that provides a comprehensive suite of business applications including accounting, inventory management, sales, procurement, project management, and more.
Note: You need to change the keystroke output mode to Simulate keystroke before use. Please refer to section 2.4.1.
Orcascan
Orcascan is a barcode scanning app that offers a variety of features including barcode creation, printing, and scanning, supports offline use, and can integrate with multiple systems such as Google Sheets, Excel, and Power Bl. The application allows you to export the scanned barcode data in Excel format.
Note: You need to change the keystroke output mode to Simulate keystroke before use.
Please refer to section 2.4.1.
Inflow
Inflow is an inventory management software. It provides barcode scanning, inventory tracking, order management, supplier management, and other functions to help companies manage inventory and order processes more e
fficiently. 
Reset Options
Reset network settings and app preferences. You can also reset your device to its factory defaults.
- From Settings, tap0 System
0 Reset options. The following options are available:
- Reset Wi-Fi, mobile & Bluetooth: You can reset Wi-Fi, mobile data, and Bluetooth settings with Reset network settings.
- Reset app preferences: You can reset all app preferences settings and will not lose any app data.
- Erase all data (factory reset): You can reset your device to factory defaults, erasing all data from your device.
Note: This action permanently erases ALL data from the device, including Google or other account settings, system and application data and settings, downloaded applications, as well as your music, photos, videos, and other files.
For more help, please scan the following QR code to enter our help center.
Contact us
WhatsApp: +86 13302482997
Scan the QR code for WhatsApp online chat
MUNBYN provides an 78-month warranty and lifetime free service.
If you encounter any issues with the product, please contact the MUNBYN team to promptly receive troubleshooting tips or a replacement.
- Email: support@munbyn.com (24*7 on line support)
- Website: www.munbyn.com (how-to videos, warranty details)
- Phone: + l 628 229 3612
- Skype: munbyn
FAQ
Why can't the PDA be turned on or charged?
Check to see if your device has a removable battery. If your device has a removable battery, open the back cover and remove the battery insulation. Due to the impact of long-distance transportation, the battery may enter sleep mode. Please charge it for half an hour before turning it on. Please try to press and hold the power button for more than 20 seconds to force a restart. If the battery still cannot be turned on after charging for half an hour, please check whether there is a problem with the charging plug or charging cable. Please replace the charging plug/charging cable to charge. If you have a charging stand, please use the charging stand to perform a charging test. If the device has a removable battery and you have extra batteries, try replacing the batteries and try again.
Why does the scan light not appear after I press the PDA scan button?
Refer to Section 2.7.l to restore lnfowedge to factory settings. Please try restarting your device. Please try to reset the device. Please refer to Chapter 4.0. If this does not work, please contact Technical Support.
How to use the battery correctly?
The battery is a lithium-ion battery. If it is out of power, please charge it immediately. Do not fully charge or deplete the battery for a long time. It is best to keep 50% of the power for storage. If you do not use the PDA for a long time, it is best to unplug the battery from the PDA.
Why is the light on when scanning but there is no data?
Refer to section 2.2 to check whether this barcode is enabled. Please try to change the scan output mode to simulate keystrokes. Please refer to section 2.4.1.
Why is there a lack of numbers in the output when I scan successfully?
(Characters) Please refer to section 2.2 to enable the transmission check digit setting for this barcode type.
Documents / Resources
 |
MUNBYN IPDA086 Pro Android Barcode Scanner [pdf] User Guide IPDA086 Pro Android Barcode Scanner, IPDA086 Pro, Android Barcode Scanner, Barcode Scanner, Scanner |