SKYDANCE ES-D Dual PIR Sensor Plus Dual Push Button SPI Controller

Speċifikazzjonijiet

• Input Voltage: 5-24VDC
• Kurrent tad-Dħul: 15A
• Sinjal tal-Ħruġ: 2XSPI(TTL)
• Numru tal-Pixel: Max 960 PIR sensor + Push-button
• Garanzija: 5 snin
• Temperatura tat-Tħaddim: -30°C sa +55°C
• Case Temperature (Max.): +65°C
• Klassifikazzjoni tal-IP: IP20
• Daqs tal-Pakkett: L175 x W120 x H35mm
• Piż Gross: 0.27kg

Istruzzjonijiet għall-Użu tal-Prodott

Strutturi u Installazzjonijiet Mekkaniċi:
Segwi d-dijagramma tal-wajers ipprovduta għall-installazzjoni.

• Step 1: Stair Light Application with PIR Sensor
  Connect the PIR sensor as per the wiring diagram for color or white light flow control.
• Step 2: Stair Light Application with PIR Sensor
  Connect the PIR sensor according to the wiring diagram for color or white light step control.
• Step 3: Sequential Switching Control
  Connect one push switch with multiple controllers for sequential switching control following the wiring diagram.

ES-D

Sensor PIR doppju + Kontrollur SPI tal-buttuna tal-Imbotta Doppju

• Sensor PIR doppju + input buttuna doppja RGB jew kontrollur SPI tad-dawl abjad karatteristiċi sensur tad-dawl tal-ġurnata.
• Two groups same SPI(TTL) signal output, drive 28 kinds of IC digital RGB or white LED strip, IC type, and R/G/B order can be set.
  ICs kompatibbli:
  TM1804, TM1809, TM1812, UCS1903, UCS1909, UCS1912,UCS2903,UCS2909, UCS2912, WS2811, WS2812, TM1829, TM1914A, GW6205,GS8206,GS8208,LPD6803, LPD1101,D705, UCS6909, UCS6912, LPD8803,LPD8806, WS2801, WS2803, P9813, SK9822, SM16703P.
• When applied to stair light, supports four output modes: color fow, white fow, color step, and white step.
• Kontroll ta 'swiċċjar sekwenzjali huwa realizzat meta kontrolluri SPI multipli huma konnessi ma' buttuna waħda ta 'swiċċ tal-imbotta li tirrisettja waħedha.
• Kuluri tad-dawl multipli u tipi ta 'bidla jistgħu jintgħażlu b'veloċità u luminożità aġġustabbli.

Parametri Tekniċi

Strutturi u Installazzjonijiet Mekkaniċi

Dijagramma tal-Wiring

1. Applikazzjoni tad-dawl tat-turġien, qabbad mas-sensorju PIR, kulur jew kontroll tal-fluss tad-dawl abjad
2. Stair light application, connect with PIR sensor, color or white light step control
3. One push switch connects with multiple controllers for sequential switching control

Nota: 

1. If the SPI LED strip is a single-wire control method, the DATA and CLK signal line outputs of the controller are the same, and one controller can connect four LED strips.
2. Jekk l-istrixxa LED SPI hija metodu ta 'kontroll b'wajer doppju, kontrollur wieħed jista' jgħaqqad żewġ strixxi LED.
3. When the SPI strip load does not exceed 15A, the same power supply can simultaneously power the ES-D controller and the SPI strip at the same time.
   When the load on the SPI strip exceeds 15A, separate power supplies are required for the ES-D controller and the SPI strip.
   Only DATA and GND signal lines are connected between the ES-D controller and SPI strip.
4. Is-sensorju PIR jista 'jiġi sostitwit b'senser ta' riflessjoni infra-aħmar tat-taraġ (ES-T) jew sensuri oħra li joħorġu sinjali ta 'livell ta' 5V.
5. Il-mudell tal-fluss tad-dawl tal-kulur jew abjad jista 'jikkontrolla sa punti ta' 960 pixel tal-istrixxa SPI.
6. The color or white light step model defaults to 30 steps with 10 pixels per step. The step number x pixel length per step must be ≤ 960.

L-issettjar tal-parametri

Long press the M and ◀ keys for 2s simultaneously, and enter the light parameters setting state: set the light type, and LED strip connection mode (flow or step). Pixel length, step number, light on/off mode, sensor turn off light delay time, daylight detection, self-reset push switch turn on or off light delay time.

1. Light typesetting
   Short press the M key to enter the light type setting interface;
   Short press ◀ or ▶ key to switch light type.Dawl abjad bi żibeġ: 1 pixel with 3 same data, control 3-bead white LED, display “L-1”.
   Dawl abjad bi żibeġ: 1 pixel b'data 1, kontroll LED abjad 1-xoffa, wiri "L-2".
   Dawl tal-kulur RGB: 1 pixel bi 3 data, kontroll wieħed R/G/B LED, wiri "L-3".
2. LED strip connection mode setting
   Short press the M key to enter the LED strip connection mode setting interface;
   Short press the ◀ or ▶ key to switch LED strip connection mode.Flow mode: Straight line digital pixel LED strip connection mode, display “o-L”.
   Modalità pass: Z-shape digital pixel LED strip connection mode, display “o-S”.
3. Pixel length setting
   Short press the M key to enter the pixel length setting interface;
   Short press the ◀ or ▶ key to set the pixel length.Pixel length:
   For color or white flow mode, set the number of pixel points, the range is 032-960, and display “032”-“960”.
4. Step number and step pixel length setting
   Short press the M key to enter the step number setting interface;
   Short press the ◀ or ▶ key to set the step number.
   Short press the M key to enter the step pixel length setting interface;
   Short press the ◀ or ▶ key to set the step pixel length.Step numbers and step pixel length:
   For color or white step mode, set the number of steps and pixel dot number of each step. Step number: the range is 8-99, display “S08”-“S99”;
   Pixel dot number of each step: the range is 2-99, display “L02”-“L99”.
   The step number x pixel dot number of each step number must ≤ 960.
5. Light on/off mode setting(i.e., set the sensor activated and self-reset button to turn on or off the light mode (Table 1)
   Short press the M key to enter the light on the setting interface;
   Short press ◀ or ▶ key to switch two lights on mode:
   Sequential light on:
   The light turns on sequentially from the beginning to the end, displaying “onS”. Synchronized light on:
   The light turns on synchronously, and displays “onC” .
   Short press the M key to enter the light off-setting interface;
   Short press ◀ or ▶ key to switch three lights off mode:
   Dawl sekwenzjali mitfi:
   The light turns off sequentially from the beginning to the end, displaying “oFS”. Sequence light off in reverse: The light turns off sequentially from end to beginning, displaying “oFb”. Synchronized light off: The light turns off synchronously, and displays “oFC” .Lista ta' modi kif tixgħel/itfi l-kombinazzjonijiet tad-dawl:

   Wiri	Isem
   onS + oFS	Dawl sekwenzjali mixgħul, dawl sekwenzjali mitfi
   onS + oFb	Sequential light on, sequential reverse light off
   onS + oFC	Dawl sekwenzjali mixgħul, dawl sinkronizzat mitfi
   onC + oFS	Dawl sinkronizzat mixgħul, dawl sekwenzjali mitfi
   onC + oFb	Synchronized light on, sequential reverse light off
   onC + oFC	Dawl sinkronizzat mixgħul, dawl sinkronizzat mitfi

6. Sensor delay off-time setting
   Short press M key enter sensor delay off time setting interface;
   Short press the ◀ or ▶ key to switch 10 levels of delay time.Sensor delay off time:
   5sec (d05), 10sec (d10), 30sec (d30), 1min (01d), 3min (03d), 5min (05d), 10min (10d), 30min (30d), 60min (60d), cancel (d00), set cancel means not turn off the light.
7. Daylight detection setting
   Short press the M key to enter the daylight detection setting interface;
   Short press the ◀ or ▶ key to switch 6 levels of daylight detection.Daylight detection:
   Set the light sensing detection threshold (6 levels):
   10Lux (Lu1), 30Lux (Lu2), 50Lux (Lu3),100Lux (Lu4), 150Lux (Lu5), 200Lux (Lu6), Off (LoF). Factory default light sensing detection is Off (LoF).
   When light sense detection is on, PIR sense turns on the light only
   when the ambient light is lower than a threshold value.
8. Self-reset push switch turn on or off light delay time setting
   Short press the M key enter the push switch turn on the light delay time setting interface;
   Short press the ◀ or ▶ key to set the delay time.
   Short press M key enter push switch turn off light delay time setting interface;
   Short press ◀ e  r ▶ key to set the delay time.Swiċċ tal-imbotta li jissettja waħdu Ixgħel il-ħin tad-dewmien tad-dawl:
   Setting range 0-15.5s, the smallest unit 0.5s, display “o00”-“o95”-“oF5”, A-F indicates that 10-15s.
   Setting 0s means turning on the light immediately.
   Self-reset push switch turns off light delay time:
   Setting range 0-15.5s, the smallest unit 0.5s, display “c00”-“c95”-“cF5”, A-F indicates that 10-15s.
   Setting 0s means turning off the light immediately.

Long press the M and ▶ keys for 2s simultaneously,and enter the LED strip parameters setting state: set the chip type and RGB color order.

1. Chip typesetting
   Short M key enters the chip type setting interface;
   Short press ◀ or ▶ key to switch chip type (Table 2).Lista ta 'tipi ta' IC strip LED:

   Nru.	Tip IC	Tip IC kompatibbli	Sinjal tal-ħruġ
   C11	TM1809	TM1804,TM1812,UCS1903,UCS1909, UCS1912, UCS2903,UCS2909,UCS2912, WS2811,WS2812, SM16703P	DEJTA
   C12	TM1829		DEJTA
   C13	TM1914A		DEJTA
   C14	GW6205		DEJTA
   C15	GS8206	GS8208	DEJTA
   C21	LPD6803	LPD1101,D705,UCS6909,UCS6912	DEJTA, CLK
   C22	LPD8803	LPD8806	DEJTA, CLK
   C23	WS2801	WS2803	DEJTA, CLK
   C24	P9813		DEJTA, CLK
   C25	SK9822		DEJTA, CLK

2. RGB color order setting
   Short press M to enter the RGB order setting interface;
   Short press the ◀ or ▶ key to switch the R/G/B order (Table 3).Ordni tal-kulur RGB tal-istrixxa LED:

   R/G/B order	RGB	RBG	GRB	GBR	BRG	BGR
   Wirja diġitali	0-1	0-2	0-3	0-4	0-5	0-6

3. Quit the parameter setting.
   Long press the M key for 2s or wait for 15, and quit the parameter setting state.

Issettjar tal-effett tad-dawl

1. Light color setting
   Short press the ◀ key to switch 10 light colors in sequence (Table 4).
2. Light change type setting
   Short press ▶ key to switch 5 light change types in sequence (Table 5).
3. Light effect parameter setting (i.e., speed, brightness, Self-defined R/G/B color)
   Short press the M key to switch three parameter items;
   Short press the ◀ or ▶ key to adjust the value of each parameter item.
   Speed, brightness, and self-defined R/G/B color parameter value description:
   Speed: 1-8 levels adjustable, display “S-1”-“S-8”, S-8 is the maximum speed.
   Brightness: 1-10 level adjustable, display “b10”-“bFF”, bFF means maximum brightness 100%. Self-defined R/G/B color: 0-255 (00-FF) adjustable.
   R channel displays “100”-“1FF”; G channel displays “200” – “2FF”; B channel displays “300”-“3FF”.
4. Quit the light effect parameter setting.
   Long press the M key for 2s or wait for 15, and quit the light effect parameter setting state.
   

Nota:

1. White flow / white step mode does not support a self-defined R/G/B color function.
2. For color flow/color step mode, the light color and light change type are combined to form 50 kinds of light effects.
3. For color flow/color step / white flow / white step mode, can be adjusted in speed and brightness.

Issettjar tal-Parametru Default tal-Fabbrika

• Long press ◀ and ▶ keys for 2s simultaneously, restore factory default parameters, and display “RES”.
• Factory default parameters: RGB color light flow output, 300 pixels, sequential light on, sequential light off, 30s delay off time, disable daylight detection, push switch turn-on delay and turn off delay is 0s, chip type TM1809, RGB order.

Tip ta' kulur (it-tieni ċifra):

LE.	Isem
0	Rxxx Gxxx Bxx（x  User de ne）
1	Aħmar
2	Oranġjo
3	Isfar
4	Aħdar
5	Ċjan
6	Blu
7	Vjola
8	R/G/B 3 kulur
9	7 kulur

Tip ta' bidla fil-kulur/dawl abjad (it-tielet ċifra):

LE.	Isem
1	Fluss
2	Chase
3	Float
4	Trail
5	Trail+black section

Applikazzjoni tipika

1. Dual PIR sensing
   Qabbad żewġ sensuri PIR biex tirrealizza kontroll awtomatiku tad-dawl tat-taraġ.
   The UP PIR sensor is installed at the bottom of the staircase, when sensing a person, the digital tube instantly displays “-u-“, the light is automatically turned on, and the light is turned off with a delay.
   The DW PIR sensor is installed at the top of the staircase, when sensing a person, the digital tube instantly displays “-d-“, the light is automatically turned on, and the light is turned off with a delay.
   Jekk issettja s-sejbien tas-sensorju tad-dawl tal-jum fuq, id-dawl jinxtegħel biss f'ambjenti jiskuraw jew bil-lejl.
2. Dual self-reset push switch control
   Connect two push switches for manual control of stair lights.
   Is-swiċċ push UP huwa installat fil-qiegħ tat-taraġ; l-iswiċċ push DW huwa installat fil-quċċata tat-taraġ.
   Set the self-reset push switch to 0s for both light on delay and light off delay.
   Short press the self-reset push switch to turn on the light, display the current light effect mode;
   short press the self-reset push switch again, turn off the light, and display “OFF”.
   Long press the UP self-reset push switch to adjust the brightness, range 10-100%, digital tube display “b10”-“bFF”. Note: The DW self-reset push switch does not have the function of adjusting the brightness.
   Using a self-reset push switch control will ignore the daylight sense detection.
3. Self-reset switch connects multiple controllers for sequential switching control.
   Multiple controllers are connected to one or two push switches at the same time to realize sequential switching control.
   Set the self-reset push switch light on/off delay time of multiple controllers to incremental or decremental values, for example:
   set 1-4# controllers’ push switch light on delay time to 0s, 1s, 2s, 3s respectively, and push switch light off delay time to 3s, 2s, 1s, 0s respectively. In this way, 1-4# controllers will turn on the lights in the same order, and turn off the lights in the reverse order.
   Short press the self-reset push switch to turn on the lights sequentially. During the delayed light on time, digital display “don”.
   When the light is on, display the current light dynamic mode.
   Short press the self-reset push switch again to turn off the lights sequentially. During the delayed light off time, the digital display “doF”.
   When the lights are off, the digital display is “OFF”.

Nota:

• When the lighting effects of multiple controllers are confused, it can be quickly restored by double-clicking the self-reset push switch.
• Using the self-reset switch to control multiple controllers will ignore the sensordelay-offf timeand daylight detection settings.

Installazzjoni tas-sensorju PIR

Avviż għall-installazzjoni tas-sensorju PIR

1. Rakkomandat għall-immuntar mal-ħajt.
2. Jekk is-sensor ikun espost għal dawl tax-xemx dirett, jiġi introdott sinjal ta 'interferenza.
3. Is-sensor għandu jiġi installat f'ambjent niexef u jinżamm 'il bogħod minn twieqi, arja kondizzjonata, u fannijiet.
4. Make sure that the sensor stays away from resourceless such as countertops, kitchen appliances that generate hot steam, walls, and windows in direct sunlight, air conditioners, heating, refrigerators, stoves, and so on.
5. Nirrakkomandaw li l-għoli tal-installazzjoni immuntat mal-ħajt huwa 1-1.5 metri u l-għoli tal-immuntar tas-saqaf ma jkunx aktar minn 3 metri.
6. M'għandux ikun hemm kenn (skrin, għamara, bonsai kbir) fil-medda ta 'skoperta.

Lista tal-Ippakkjar

Mistoqsijiet Frekwenti

• Q: X'inhu l-perjodu ta 'garanzija għall-prodott?
  A: Il-prodott jiġi b'garanzija ta 'sena.
• Q: X'inhi l-firxa tat-temperatura operattiva tal-prodott?
  A: The product can operate in temperatures ranging from -30°C to +55°C.
• Q: What is the maximum pixel number supported by the product?
  A: The product supports a maximum of 960 PIR sensor + Push button pixel number input.

Dokumenti / Riżorsi

SKYDANCE ES-D Dual PIR Sensor Plus Dual Push Button SPI Controller [pdfManwal tas-Sid ES-D, ES-D-1, ES-D Dual PIR Sensor Plus Dual Push Button SPI Controller, ES-D, Dual PIR Sensor Plus Dual Push Button SPI Controller, Dual Push Button SPI Controller, Push Button SPI Controller, Button SPI Controller

Referenzi

• Manwal għall-Utent