MOON 341 Integrated Amplifier

specifications
- output power @ 8 Ω 100 W
- output power @ 4 Ω 200 W
- input sensitivity 0.3 V – 4V
- input impedance 9.5 kΩ
- gain 40 dB
- frequency response 5 Hz – 100 kHz +0dB/ –3 dB
- total harmonic distortion @ 1 W 0.009%
- total harmonic distortion @ 100 W 0.003%
- intermodulation distortion 0.005%
- signal -to-noise ratio 108 dB
- crosstalk –108 dB
- damping factor 425
- power consumption (idle) 26 W
- power consumption (standby) 24 W
- power consumption (low -power standby) 6 W
- dimensions 42.9 cm x 8.7 cm x 38.5 cm
- width x height x depth 16.9” x 3.5” x 15.2”
- weight 9 kg / 20 lbs
Safety guide
WARNING: Chemical Burn Hazard | Do not ingest the batteries.
The remote control supplied with this product contains batteries, which, if swallowed, could cause severe internal burns within two hours and lead to death. Keep new and used batteries away from children. Keep exposed batteries away from children. If you have reason to believe that batteries have been inserted into the body, seek medical attention. If the battery compartment does not close securely, stop using the remote control and contact support@simaudio.com
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near heat sources such as radiators, heat registers, stoves or another apparatus that generate heat.
- This product is intended for indoor use only.
- Do not defeat the safety purpose of the polarized or grounding -type plug. A polarized plug has two blades with one wider than the other. A grounding -type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for safety.
If the provided plug does not fit into the outlet, consult an electrician to replace the obsolete outlet. - Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where t hey exit from the apparatus. Unplug mains cord during transportation.
- Only use attachments and accessories specified by the manufacturer.
- The apparatus is heavy and requires two people to lift it. Exercise caution when maneuvering.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way such as when the power cord has been damaged; liquid has been spilled or objects have fallen into the apparatus; or the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- No naked flame sources, such as candles, should be placed on the apparatus.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
- The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of elect ric shock to persons.
- The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
- Marking by the “CE” symbol (shown right) indicates compliance of this device with the EMC (Electromagnetic Compatibility) and LVD (Low Voltage Directive) standards of the European Community.
- Waste from Electrical and Electronic Equipment (WEEE): This equipment must be sent to a separate collection facility for the recovery and recycling of electrical and electronic waste wherever dedicated facilities exist. WEEE regulations aim to contribute t o sustainable production and consumption, addressing environmental and other issues caused by the growing number of discarded electronics. The symbol for the separate collection of electrical and electronic equipment indicates that this product should not be discarded as unsorted waste.
- The Spotify Software is subject to third party licenses found here: https://www.spotify.com/connect/third-party-licenses .
- Apple, AirPlay, iPad, iPhone, and Siri are trademarks of Apple Inc., registered in the U.S. and other countries. Use of the W orks with Apple badge means that an accessory has been designed to work specifically with the technology identified in the badge an d
- has been certified by the developer to meet Apple performance standards.
- MQA technology requires less network bandwidth to stream high -quality audio files. This product implements the technology under license from MQA Limited. For more information about MQA, please visit: mqalabs.com.
- ALWAYS disconnect your entire system from the AC mains before connecting or disconnecting any cables, or when cleaning any component. To completely disconnect this apparatus from the AC mains, use the rocker switch on the rear panel or disconnect the power supply cable from the AC receptacle.
- The unit must be terminated with a three -conductor AC mains power cord, which includes an earth ground connection. To prevent shock hazard, all three connections must ALWAYS be used. Connect the unit only to an AC source of the proper voltage; both the shipping box and rear panel serial number label will indicate the correct voltage. Use of any other voltage will likely damage the unit and void the warranty.
- ALWAYS connect the unit only to an AC source of the appropriate voltage. Both the shipping box and rear panel serial number label indicate the correct voltage. Incorrect voltage could damage the unit and void the warranty.
- AC extension cords are NOT recommended for use with this product. The mains plug of the power supply cord shall remain readily accessible.
- NEVER use flammable or combustible chemicals for cleaning audio components.
- NEVER operate the unit with any covers removed. There are no user -serviceable parts inside. An open unit, especially if it is still connected to an AC source, presents a potentially lethal shock hazard. Refer all questions to authorized service personnel o nly.
- NEVER wet the inside of the unit with any liquid. If a liquid substance does enter your unit, immediately disconnect it from the AC mains and take it to your MOON Partner for a complete check -up.
- NEVER spill or pour liquids directly onto the unit.
- NEVER block air flow through ventilation slots or heatsinks.
- NEVER bypass any fuse.
- NEVER replace a fuse with a value or type other than those specified.
- NEVER attempt to repair the unit. If a problem occurs, contact a MOON Partner.
- NEVER expose the unit to extremely high or low temperatures.
- NEVER operate the unit in an explosive atmosphere.
- ALWAYS keep electrical equipment out of reach of children.
- ALWAYS unplug sensitive electronic equipment during lightning storms.
- WARNING: Do not expose batteries or battery pack to excessive heat such as sunshine, or fire or the like.
Let the music guide you
- The Compass Collection from MOON is more than a mere line of products. It’s not even just a promise of exceptional quality and style. The Compass Collection is an excuse to dream; a conceptual offering to ambitious individuals who deserve the finest home listening experience imaginable.
- Envisioned for the music lovers of tomorrow and crafted for the audiophiles of today, the Compass is your way forward, a gateway to the MOON universe—engineered for outstanding performance and lasting reliability, and drawing inspiration from the acclaimed
- North Collection. The Compass Collection harmonizes modern aesthetics with timeless sophistication. Sleek, elegant lines and minimalist design combine with discreet, intelligent features and an intuitive interface to convey a striking appearance, elevating and refining the listening environment.
- Every note and beat resonate with unprecedented clarity to transform casual listeners into passionate connoisseurs.
- Let the music guide you on your journey with the Compass Collection.
Before setting out… inspect your MOON 341
- Carefully remove the unit from its packaging. Visually inspect it, and in the case of damage, report it to your MOON retailer immediately.
- The packaging materials were designed to protect this product while in transit. Store these materials in a dry location for the duration of the warranty period.
- The information contained in this guide is subject to change without notice. The most recent version is available at simaudio.com/guides downloads.
The MOON 341 includes:
- MOON CRM-4 remote control
- battery compartment token
- carrying pouch
- AAA batteries (2)
- spare fuse
- quick-start guide
- power cable
- ethernet cable
- warranty information sheet
- Note the serial number of your MOON 341 for future reference.
install your MOON 341
Carefully consider the location and environment of your installation.
Set the 341 upon an open, stable, and flat surface. The device requires sufficient space above and around it to adequately disperse the heat it generates. Maintain a minimum gap of 5 cm (2”) around the sides and 10 cm (4”) above of the unit to enable airflow.
The performance of this device will continue to improve during the first 100 hours of listening. The spirit of this recommendation is to temper expectations and delay your first critical listening session until after all the components in the circuit have stabilized. But that doesn’t mean you can’t enjoy it from first note. It just means that it’ll behave most consistently after a few weeks of listening.
Front panel
The display provides useful feedback about the state of the device. It identifies the active input and volume of the preamplifier and the sample rate of the DAC. On the MiND input, it can identify the stream.
Headphones: ¼” TRS (stereo) output
Connecting headphones automatically mutes the loudspeaker outputs.
Rear panel 
RIGHT OUTPUT & LEFT OUTPUT: binding posts for connecting loudspeakers
Insert banana pins through the holes in the extremities of the barrels or unscrew the barrels to expose a gap underneath for spades or bare wire contacts.
ANALOG INPUTS
- A1 | A2 | A3: single-ended (RCA) connections for a line-level analog source device
- BALANCED: differential (XLR) connections for balanced analog line-level source devices
- PHONO: single-ended (RCA) connections for accommodating moving-magnet (MM) and moving-coil (MC) phono cartridges
- GND: terminal to ground a turntable
- ANALOG OUTPUT: variable-volume output for use as a preamplifier to connect the 341 to power amplifiers, subwoofers, or active loudspeakers
- NETWORK: network (RJ-45) connections for ethernet cables…
- to connect the device to a network router
- to extend the network to an additional device (eg, NAS device or TV)
- to join a MOONLink Group with compatible MOON products
- USB SERVICE: for use only by authorized service technicians
- 12V TRIG OUT: mini-jack (TS) connection for coupling a compatible power amplifier to synchronize Standby behaviors
- FUSE: magazine containing a power supply fuse
- Please appreciate that while some users may report improvements in the performance of their audio equipment when original parts are replaced with after market parts, MOON cannot guarantee the proper functioning of its products under such conditions. Our engineers have ensured that the original fuse should protect your device from catching fire due to electrical calamities. All security, quality, and performance testing, as well as standards certification, is performed with specific components, and any modification from the original design may void its warranty.
- AC POWER: for connecting the power cable
- POWER: switch for toggling the device on [–] and off [O]
With the power switch on, the unit may be toggled into and out of Standby using the button on the front panel, a remote control, the mobile app, or by MOONLink.
The unit may require up to a minute to connect to the network. For best performance, the device should remain powered up and may be toggled into Standby when not in use. It should be powered down during extended absences by disconnecting the power cable.
Begin your journey
Consult the included quick -start guide . Then , follow these steps to connect your 341 .
- Connect the RIGHT OUTPUT and LEFT OUTPUT terminals on the rear panel of the amplifier to the corresponding terminals (positive [+] with red and negative [ –] with black) on your loudspeaker s.
- Connect audio sources —like a CD or network player —to the INPUTS. You may connect up tothree line -level sources to the ANALOG INPUTS, as well as one turntable to the PHONO input.
- For use with MOONLink (optional) or to update the device firmware , connect the ethernet cable to a network router.
- Connect the supplied power cable between the 341 and an electrical outlet.
- Toggle the POWER rocker switch to the On [ –] position.
- After the button icons stop pulsating, press the
button. - To learn more about this product, follow this QR code, or visit our website.

Plot your course
Setup
The device features an extensive menu for configuring and customizing many of its functions.
Use the
buttons along with the volume knob to navigate the menu system.
Inputs
Each input may be personalized.
- Label: the name that appears on the 341 display
Select a predefined label or manually enter a custom label. - Offset: adjusts the gain level applied to the input
The volume level of each input may be fine-tuned to match the volume levels of source components connected to other inputs. - Enable: toggles whether the input is available to select
The input may be hidden to reduce the number of unused inputs to scroll through. - Home Theatre Bypass: disables 341 volume control for the specified input
This mode sets the preamp volume to unity gain permitting the volume to be controlled exclusively by a home theatre processor or audio-video receiver - Phono Configuration (PHONO): selects between pre-set configurations for either a Moving Magnet (MM) or a typical Moving Coil (MC) phono cartridge
When the 341 is set to the phono input, there is 100 times more gain on the audio signal for MM and 1000 times more for MC than there is through the other inputs. This can reveal unwanted noise, especially when nothing is connected to the input.
One common noise, a rapid pulsing, is the sound generated only while the MiND is connecting to a wireless network. To eliminate this noise, consult the next section on connecting to a network.
Network
Review useful details about the network connection of the device.
Remote Control
The 341 may link with a MOON BRM-1 remote control (sold separately).
- Link Remote searches for a nearby BRM-1 remote control, displaying its unique ID on both devices and permitting them to be associated.
- Unlink Remote displays associated BRM-1 units permitting them to be disassociated from this device.
- Information displays useful details about the associated BRM-1 units.
- Refer to the separate Guide included with the BRM-1 for more information.
- The Infrared receiver may be Enabled or Disabled, a practical solution when a remote control from another device inadvertently affects the 341, or when controlled exclusively with a BRM-1 or the MiND Controller app.
MOONLink
MOONLink technology makes MOON products more intelligent. A single button press can trigger automated behaviours and simultaneously operate multiple devices on the network. MOONLink toggles
Standby, adjusts display brightness, controls volume, and selects specific inputs on the appropriate devices in the Group.
- MOONLink Group: a symbiotic relationship between MOON devices
- Name: identifies a device within the Group
- Group ID: assigns a number from 1 to 10 to the device
- Assigning the same ID to other devices joins them together as a Group.
- Status: displays information about the device
- Firmware: verifies the firmware of the device and updates it when possible
- Reset: reverts the name and ID to their default values.
- Resetting a MOONLink configuration removes the device from its Group.
- Available Devices: lists devices on the network that could be added to a Group
- MOON DAC identifies which input is used to connect a DAC with MOONLink compatibility.
- When scrolling through the inputs on a BRM -1, an additional arrow appears on the selected input.
- Tapping the centre of the display switches the BRM -1 to selecting the inputs on the DAC.
- Holding the button on the front panel for two seconds automatically toggles Standby mode on all the devices in the MOONLink Group.
- For best results, do not include multiple preamplifiers in a MOONLink Group.
Display
- Display On
The display may be disabled so that only user interaction temporarily activates the display. - Brightness
- Brightness Level: variable from 0% to 100%
- MOONLink Brightness Sync: duplicates the brightness adjustments of devices in a
MOONLink Group
- Screen Saver
Two screen saver styles are available, which may also be disabled.- Mode: which behaviour triggers the screen saver
- activate the screen saver after 20 minutes of silence
- activate the screen saver after 20 minutes of inactivity
- Style: display a floating logo or a blank screen
Volume Settings
- The highest volume setting of the preamp is 80.
- Startup Volume: sets a default initial volume level
- Maximum Volume: sets an upper threshold to prevent accidents
- Balance: Skews the perceived centre of the stereo image to one side or the other
Standby Settings
- Full Power: most of the electronics remain powered up while in Standby
- Low Power: most of the electronics remain powered down while in Standby
- Auto-Standby: engages Low Power Standby after 20 minutes of inactivity
Language
Convert the menu to appear in one of three languages:
- English
- Français
- Español
Firmware
- Certain hardware components in this device require firmware to function.
- Versions: displays the various firmware versions currently installed
- Update: begins the procedure of verifying the availability of newer firmware
- If newer firmware is available, the 341 will display a prompt to update its firmware.
Information
The 341 displays device information, including its certifications and serial number.
Reset
The reset procedure reverses all customizations—including input configurations—to factory default settings. It does not revert the firmware to an earlier version.
Enjoy your journey
Use
the buttons to select which input is playing through the 341, and adjust the volume accordingly using the volume knob.
Remote control
Products in the Compass Collection feature the CRM-4 remote control.
The CRM-4 operates on two AAA batteries (included). Insert the battery compartment token (included in the CRM-4 pouch) into the slot on the bottom of the CRM-4, and turn clockwise to release the battery cover and insert the batteries.
Buttons
- The CRM-4 is designed to operate several types of products, notably: a preamplifier, an integrated amplifier, a CD player, and a Digital-to-Analog Converter (DAC). Pressing one of the three buttons at the bottom of the keypad alters which set of commands it
- emits. To operate the MOON 341, press the AMP button when using the CRM-4 for the first time and after using it with a different type of product.
- The buttons on the CRM-4 operate the most common functions of the 341, and many functions on other products as well.
- Setup: accesses the extensive configuration menu to personalize the 341

The rest of the buttons are as follows… 
Documents / Resources
![]() | 341 Integrated Amplifier |
References
- User Manualmanual.tools

