mokee Midi Cot Bed Instruction Manual

mokee LogoMidi Cot Bed
Instruction Manual
mokee Midi Cot Bed

Midi Cot Bed

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Great design is all about making life easier and beautiful. The moKee Midi Cot does just that, with its modern colour range, minimalist Scandinavian design and a range customization to fit your needs and budget. One side can easily be removed when your child is around 24 months, increasing the moKee midi lifespan to up 4 years old.

IMPORTANT – RETAIN FOR SUBSEQUENT CONSULTATION
– READ CAREFULLY CONFORMS TO STANDARD SAFETY REQUIREMENTS EN 716
Warning: Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires, gas fires, etc. in the near vicinity of the cot.
Warning: Do not use the cot if any components are broken, damaged or missing, and only use spare parts approved by the manufacturer.
Warning: Do not leave anything in the cot or place the cot close to another product, which could provide a foothold or present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords
Warning: Do not use more than one mattress in the cot.

CAUTION:
The cot base is safest at the lowest position and must be set to this position as soon as the baby is old enough to sit up.
The supports used to adjust the base when it is set to the low position must be removed.
The thickness of the mattress selected must be such that the internal height (i.e. the distance between the surface of the mattress and the upper part of the cot frame) is at least 500 mm with the base at the lowest position and at least 200 mm at the highest position.
The markings on the side of the stand indicate the maximum thickness for the mattress to be used when the base is set to different positions.
The mattress to be used with this cot must be designed for 70 cm x 140 cm cots and must not exceed 10 cm in height.
The length and width of the mattress must be such that the space between the mattress and the sides and ends of the cot does not exceed 30 mm.
After assembly, check that all the assembly mechanisms are correctly tightened and are checked regularly, and re tightened if necessary.
Care: clean using a damp sponge and warm, soapy water. Never use any abrasive products.
When the child is able to get out of the cot on its own, the cot must no longer be used for this child, to prevent any risk of falling.
ZACKARO LIMITED. Office 141 405 Kings Road, London, England, SW10 OBB, UK

In the set:

You will need (not included)mokee Midi Cot Bed - Figure 1Options available (not Included):

mokee Midi Cot Bed - Figure 2buy at mokee.eu

Important! Do not use caster weels when 1 side is open

mokee Midi Cot Bed - Figure 3

mokee Midi Cot Bed - Figure 4 mokee Midi Cot Bed - Figure 5
mokee Midi Cot Bed - Figure 6 mokee Midi Cot Bed - Figure 7

IMPORTANT! – THIS COT IS NOT A CO-SLEEPER – ONLY REMOVE THE LONG SIDE WHEN BASE (H) IS AT ITS LOWEST SETTING & IN CONJUNCTION WITH THIS WOODEN PANEL SECURELY ATTACHED (I)

mokee LogomoKee.eu

Documents / Resources

PDF thumbnailMidi Cot Bed
Instruction Manual · Midi Cot Bed

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. we have taken the side off this but the slat just keep falling out. can anyone help?

    Liz asks we have taken the side off this but the slat just keep falling out. can anyone help?
    Manuals+ clarified question
    Question

    Why are the slats falling out of my moKee Midi Cot Bed after removing one side?

    Answer

    When converting the moKee Midi Cot Bed into a toddler bed by removing one side, it is essential to follow specific safety and structural requirements to ensure the base remains stable:

    • Base Height: According to the manual, you should only remove the long side when the bed base (H) is at its lowest setting.
    • Wooden Panel (I): To maintain structural integrity and prevent the slats from shifting or falling out, you must install the wooden panel (I) (often referred to as the toddler rail or support board) in place of the removed side. This panel is shown in the assembly diagrams on pages 7 and 8 and is required to keep the frame securely tightened.
    • Tighten All Fixings: Ensure all screws (A, B, and C) are fully tightened using the provided Allen keys (E1/E2). If the frame is even slightly loose, the slats may lose their tension and fall out.
    • Safety Warning: The manual explicitly states that this cot is not a co-sleeper. Do not use the bed with a side removed unless the base is at the lowest position and the specific wooden support panel is securely attached.

    If you are missing the wooden panel (I), you should contact moKee support at hello@mokee.co.uk for assistance.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.