User Manual for LG Electronics models including: TM16FNNABM0, TM16FNNABM0 5G NR LTE Embedded Modules, 5G NR LTE Embedded Modules, LTE Embedded Modules, Embedded Modules, Modules
LG Electronics USA, Inc. TM16FNNABM0 BEJTM16FNNABM0 BEJTM16FNNABM0 tm16fnnabm0
File Info : application/pdf, 16 Pages, 1.67MB
DocumentDocumentUser Manual (TM16FNNABM0) FCC ID: BEJTM16FNNABM0 IC: 2703H-TM16FNNABM0 14/16 Contents 1. Product Introduction ....................................................................................................... 3 1.1 Environmental Specifications ................................................................................... 4 1.2 Electrical Specifications ........................................................................................... 4 1.2.1 Absolute Maximum Rating and ESD Ratings.................................................. 4 1.2.2 Current Consumption ...................................................................................... 4 1.3 Mechanical Specifications ........................................................................................ 5 1.3.1 Physical Dimensions ...................................................................................... 5 1.3.2 Mechanical Drawing....................................................................................... 5 1.3.3 Host Equipment............................................................................................... 6 2. RF Specification ...............................................................................................................7 2.1 Module support Band .................................................................................................8 2.2 Module Support Power Level .....................................................................................9 3. Module Installation ......................................................................................................... 11 4. FCC Notice .....................................................................................................................12 5. ISED Notice ....................................................................................................................13 6. KDB 996369 D03 OEM Manual...................................................................................... 14 2/16 1. Product Introduction The TM16FNNABM0 are designed for the automotive industry. They support 5G NR, LTE and WCDMA air Interface standards. The TM16FNNABM0 are based on the Qualcomm wireless chipsets and support the following bands. Table 1. Supported Band Region US NR n1/n2/n3/n5/n7/n8/n12/n20/n25/n28/ n41/n48/n66/n71/n77/n78 Band LTE B1/B2/B3/B4/B5/B7/B8/B12/B13/B17 /B20/B25/B26/B28/B29/B38/B42/B48/B66/B71 LTE ULCA CA_2A-12A/CA_12A-66A WCDMA B1/B2/B5/B8 *The red marks are bands for USA and Canada *LTE B42 is not used in USA 3/16 1.1 Environmental Specifications The environmental specification for operating and storage of the TM16FNNABM0 are defined in the the table below. Table 2. Environmental Specifications Parameter Operating Temperature Storage Temperature Humidity Temperature Range -40 to 90 (ecall 95) -40 to +95 95% or less 1.2 Electrical Specifications This section provides details for some of the key electrical specifications of the TM16FNNABM0 embedded modules. 1.2.1 Absolute Maximum Rating and ESD Ratings This section defines the Absolute Maximum and Electrostatic Discharge (ESD) Ratings of the TM16FNNABM0 embedded modules. Warning: If these parameters are exceeded, even momentarily, damage may occur to the device. Table 3. Absolute Maximum Ratings Parameter Min VPH_PWR Power Supply Input - VIN Voltage on any digital input or output pin - ESD Ratings ESD1) Primary, Diversity antenna pads - Contact 1) The ESD Simulator configured with 330pF, 2000. Max 6 2.145 1 Units V V kV Caution: The TM16FNNABM0 embedded modules are sensitive to Electrostatic Discharge. ESD countermeasures and handling methods must be used when handling the TM16FNNABM0 devices. 1.2.2 Current Consumption Table 4. TM16FNNABM0 Current Consumption (@4.1V) Mode Parameter Typical LTE Max TX Output /Full RB 550 WCDMA Max TX Output /Full RB 850 LTE Idle, Registered 2 WCDMA Idle, Registered 2 Max TBD TBD - Units mA mA mA mA 4/16 1.3 Mechanical Specifications 1.3.1 Physical Dimensions The TM16FNNABM0 embedded modules are a Land Grid Array (LGA) form factor device. The device does not have a System or RF connectors. All electrical and mechanical connections are made via the lga pad on the underside of the PCB. 1.3.2 Mechanical Drawing Module Dimension Parameter Overall Dimension Overall Module Height PCB Thickness Flatness Specification Weight Nominal 39 x 51 3.55 1.0 TBD Module Mechanical Design Max 39.35 x 51.35 3.8 1.1 0.1 Units mm mm mm mm g [TOP View_Without shield Can cover] [TOP View_With shield Can cover] [SIDE View_With shield Can cover] 5/16 1.3.3 Host Equipment This module is limited module and tested with a specific host equipment TFBMEIBN3EU and its internal antenna. Any other host equipment that has different RF/EMC characteristics and antenna would require permissive change procedure and may need additional testing. 7/16 2. RF Specification The specifications for the 5G NR, LTE and WCDMA interfaces are defined. TM16FNNABM0 is designed to be compliant with the standard shown in the table below. Table6. Standards Compliance Technology 5G NR LTE WCDMA Standards · 3GPP Release 16 · 3GPP Release 15 · 3GPP Release 9 6/16 2.1 Module support Band UMTS/LTE/NR Frequency Band Tx Rx B1 1920~1980 2110~2170 B2 1850~1910 1930~1990 B3 1710~1785 1805~1880 B4 1710~1755 2100~2155 B5 824~849 869~894 B6 830~840 875~885 B7 2500~2570 2620~2690 B8 880~915 925~960 B9 1749.9~1784.9 1844.9~1879.9 B10 1710~1770 2110~2170 B11 1427.9~1447.9 1475.9~1495.9 B12 669~716 729~746 B13 777~787 746~756 B14 788~798 758~768 B17 704~716 734~746 B18 815~830 860~875 B19 830~845 875~890 B20 832~862 791~821 B21 1447.9~1462.9 1495.9~1510.9 B24 1626.5~1660.5 1525~1559 B25 1850~1915 1930~1995 B26 814~849 859~894 B28 703~748 758~803 B29 - 717~728 B30 (2305~2315) 2350~2360 B32 B34 B38 B39 B40 B41 B42 B43 B47( C-V2X) B48 - 1452~1496 2010~2025 2570~2620 1880~1920 2300~2400 2496~2690 3400~3600 3600~3800 5855~5925 3550~3700 8/16 FDD / TDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD FDD TDD TDD TDD TDD TDD TDD TDD TDD TDD Supported RAT NA W,L,NR W,L,NR L,NR L W,L,NR L,NR W,L,NR L,NR L L L,NR L,NR L L,NR L(RXonly) L NR L L,NR B66 1710~1780 2110~2200 FDD B71 663~698 617~652 FDD B75 1432~1517 SDL n77 3300~4200 TDD n78 3300~3800 TDD n79 4400~5000 TDD - W : WCDMA - L : LTE - NR : 5G NR *The red marks of bands are used for USA and Canada *LTE Band 42 is not use in USA 2.2 Module Support Power Level Main Antenna FUNCTION MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO1 MIMO2 MIMO2 MIMO2 WCDMA WCDMA LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE NR NR NR NR NR NR NR NR NR NR NR LTE LTE NR BAND B2 B5 B2 B4 B5 B7 B12 B13 B17 B25 B26 B38 B42_ISED B48_CBRS B66 B71 n2 n5 n7 n12 n25 n41 n48_CBRS n66 n71 n77 n78 B42_ISED B48_CBRS n48_CBRS 9/16 TARGET 24.00 24.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 22.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 22.00 23.00 23.00 23.00 23.00 23.00 22.00 22.00 L,NR L,NR NR NR MIMO2 MIMO2 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO3 MIMO1+2 MIMO1+2 MIMO1+2_Tx diversity MIMO1+2 NR NR WCDMA WCDMA LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE LTE NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR n77 n78 B2 B5 B2 B4 B5 B7 B12 B13 B17 B25 B26 B38 B42_ISED B48_CBRS B66 B71 n2 n5 n7 n12 n25 n41 n48_CBRS n66 n71 n77 n78 n48_CBRS n77 n77 n78 23.00 23.00 24.00 24.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 21.50 23.00 23.00 23.00 23.00 23.00 23.00 23.00 23.00 21.50 23.00 23.00 23.00 23.00 20.00 23.00 25.00 23.00 10/16 3. Module Installation Module should be covered its shield-can cover before operation. In case of modules were supplied separately with shield-can cover, it should be covered by shield-can before use. Shield-can can covers whole part of module as below picture. Installation of Shield-can cover 12/16 4. FCC Notice Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. 12/16 5. ISED Notice This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. Avis d'Industrie Canada sur l'exposition aux rayonnements Cet appareil est conforme aux limites d'exposition aux rayonnements d'Industrie Canada pour un environment non contrôlé. Il doit être installé de façon à garder une distance minimale de 20 centimétres entre la source de rayonnements et votre corps. REMARQUE: LE FABRICANT N'EST PAS RESPONSABLE DES INTERFÉRENCES RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES APPORTÉES À CET APPAREIL. DE TELLES MODIFICATIONS POURRAIT ANNULER L'AUTORISATION ACCORDÉE À L'UTILISATEUR DE FAIRE FONCTIONNER L'APPAREIL. Operation is subject to the following two conditions: 1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device. L'exploitation est autorisée aux deux conditions suivantes : 1.L'appareil ne doit pas produire de brouillage; 2.L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 13/16 6. KDB 996369 D03 OEM Manual List of Applicable FCC Rules Part 22, 24, 27, 90, 96 Summarize the specific operational use conditions Limited module, designated enclosure that contains specific antenna inside. Professional installation equipment. Vehicle-use only. Only vehicle manufacturer can use/install this device on their vehicle. Limited module procedure Limited module, only specific host equipment can be used with this module. Applying this module to other host equipment may require additional test and permissive change procedure. RF Exposure was evaluated with specific host and certain condition. -Test plan for different host configuration Module was tested with a specific host configuration. Any other host configuration for this module would require additional test. New host configuration shall be approved with additional test. Following tests shall be considered to add new host configuration on this modular approval with Class II permissive change. - All radiated testing shall be performed on new host equipment and new antenna. - RF Exposure shall be evaluated on new host equipment. TEST ITEM ERP/EIRP Radiated Spurious Emissions RF Exposure RULE PART §22.913(a)(5) §24.232(c) §27.50(b)(9) §27.50(c)(9)(10) §27.50(d)(4) §27.50(h)(2) §27.50(j)(3) §27.50(k)(3) §90.635(b) §96.41(b) §22.917(a) §24.238(a) §27.53(c)(2) §27.53(f) §27.53(g) §27.53(h)(1) §27.53(m)(4) §27.53(l)(2) §27.53(n)(2) §90.691(a) §96.41(e)(ii) §2.1091, §2.1093 Trace antenna designs N/A 14/16 RF Exposure consideration RF Exposure evaluation was performed with very specific installation condition at 200 mm. Any other installation condition may require additional RF exposure evaluation procedure in the module or host equipment. Antennas Radiated emission test was performed with internal antenna configuration with host device. any other antenna may require additional test and permissive change procedure. Internal antenna configuration with host equipment Ant. No. Ant. 1 Ant. 2 Ant. 3 Ant.1 + Ant. 2 Frequency Range Below 3 , Above 3 Above 3 Below 3 , Above 3 Above 3 Support Band LTE NR 2, 4, 5, 7, 12, 13, 17, 2, 5, 7, 12, 25, 41, 25, 26, 38, 42, 48, 66, 42, 48, 66, 71, 77, 71 78 42, 48 48, 77, 78 2, 4, 5, 7, 12, 13, 17, 2, 5, 7, 12, 25, 41, 25, 26, 38, 42, 48, 66, 42, 48, 66, 71, 77, 71 78 48, 77, 78 WCDMA , , Band LTE 25/2 WCDMA NR 25/2 LTE 66/4 NR 66 LTE 26/5 WCDMA NR 5 LTE 7 NR 7 LTE 12/17 NR 12 LTE 13 LTE 26 LTE 38 LTE 42 LTE 48 NR 48 LTE 71 NR 71 NR 41 NR 77 NR 78 Operating Frequency () 1 850 ~ 1 915 1 710 ~ 1 780 824 ~ 849 2 500 ~ 2 570 699 ~ 716 777 ~ 787 814 ~ 824 2 570 ~ 2 620 3 450 ~ 3 600 3 550 ~ 3 700 3 550 ~ 3 700 663 ~ 698 2 496 ~ 2 690 3 450 ~ 3 550 3 700 ~ 3 980 3 450 ~ 3 550 3 700 ~ 3 800 Ant. 1 1.86 1.37 -2.43 0.92 -3.98 -4.60 -2.43 0.92 -0.66 -0.66 -0.66 -2.45 0.92 0.34 0.34 0.34 0.34 Antenna Peak Gain ( i) Ant. 2 Ant. 3 -0.32 -0.03 -3.16 -1.37 -1.37 -1.37 0.12 0.12 0.12 0.12 2.79 -1.20 -3.16 -3.16 2.79 0.96 0.96 0.96 -1.60 2.79 1.58 1.58 1.58 1.58 Ant. 1 + Ant. 2 2.00 3.24 3.24 3.24 3.24 1155//1176 Note; 1) According to KDB 662911 D01 Multiple Transmitter Output v02r01 F)2)d)(i), Port 1 + Port 2 Antenna Gain = 10 * log[(10G1/20 + 10G2/20)2 / NANT] Where, G1 = antenna gain of port 1, G2 = antenna gain of port 2, NANT = the number of antennas Host product labelling requirements The host product shall be properly labelled to identify the modules within the host product. The FCC/ISED certification label of a module shall be clearly visible at all times when installed in the host product; otherwise, the host product must be labelled to display the FCC/ISED certification number for the module, preceded by the word "contains" or similar wording expressing the same meaning, as follows: Contains FCC ID: BEJTM16FNNABM0 Contains IC: 2703H-TM16FNNABM0 16/16Microsoft: Print To PDF