MINWAX Fast-Drying Polyurethane

Fast-Drying Polyurethane

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
2. Sand to obtain a smooth uniform surface. Remove all dust with a cloth dampened with mineral spirits.
3. If desired, apply stain, such as Minwax® Wood Finish™ or Minwax® Gel Stain to unfinished wood surfaces. Follow directions for application and dry times.
4. Stir Minwax® Fast-Drying Polyurethane before and during use to eliminate settling on the bottom of the can. Stir to rotate the product from the bottom to the top of the can. NEVER SHAKE.
5. Apply a THIN coat of Minwax® Fast-Drying Polyurethane using a high-quality natural or foam brush.
6. Let dry 4-6 hours. Then lightly sand entire surface with fine sandpaper (220 grit) to ensure an even finish and proper adhesion. Remove all dust.
7. Apply second coat. If third coat is desired, repeat step 6 before application.
8. After final coat, allow 24 hours before light use.

When used on hardwood floors, use a lambswool or synthetic pad applicator or natural bristle brush and maintain a wet edge to avoid lap marks. For maximum durability, we recommend three coats. Avoid heavy traffic and replacing of furniture for 72 hours after final coat. When replacing furniture, do not slide. Do not install rugs or clean floors for 7 days.

CLEANUP: Use mineral spirits or paint thinner following manufacturer’s safety instructions.

DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

COVERAGE: Approximately 125 square feet per quart.

Note: Above dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Always test tackiness between coats. Do not sand or re-coat when surface is tacky. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. For light-colored wood surfaces, we recommend protecting with Minwax® Polycrylic® Protective Finish.

DANGER! HARMFUL OR FATAL IF SWALLOWED. COMBUSTIBLE! VAPOR HARMFUL. IRRITATES EYES, SKIN AND RESPIRATORY TRACT

CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS Contents are COMBUSTIBLE. Keep away from heat and open flame. VAPOR HARMFUL. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep the container closed when not in use. Do not transfer contents to other containers for storage.

FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call a physician. If swallowed, do not induce vomiting. Call Poison Control Center, hospital emergency room, or physician immediately.

DELAYED EFFECTS FROM LONG-TERM OVEREXPOSURE. Contains solvents that can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

DO NOT TAKE IT INTERNALLY. KEEP OUT OF REACH OF CHILDREN.
CONFORMS TO ASTM D-4236. Contact a physician for more health information.

• 2015 Minwax Company
• Upper Saddle River, NJ 07458
• Rev 0 3/24/15

MINWAX Fast-Drying Polyurethane User Manual

References

• User Manual