Upgraded 3D Printer Camera
Beagle V2
3D Printer Camera
Quick Guide Manual
https://www.mintion.net/pages/manual-download
 https://mintion-6288.myshopify.com/pages/beagle-v2-camera-firmware |
 https://mintion-6288.myshopify.com/pages/beagleprint-app-download |
| Beagle V2 Firmware Download Beagle V2 camera supports online upgrade |
Beagleprint App Download |
The lens has been adjusted, DO NOT knob t befors the WiFi connection.
PACKING LIST
CAMERA INTRODUCTION
- routsensor
- Lens
- Focus Ring
- Data Port (With Cover)
- ResetBution
- Tripod Mount (size 1/47-20)
- Vicrophone
- spesker
- usb socket
- Pover socket
- vicro s Card
- Printer ndicator
Solid Red: Printer Connected
Flashing Red: Printed Disconnected - Wifi indieator
Solid Green: WIFi Connected
Flashing Green: WiFi Disconnected
INSTALLATION BRACKET
Assemble the gimbal and tripod
ADD THE CAMERA
Download Beagleprint, Register an account and log in. 
https://mintion-6288.myshopify.com/pages/beagleprint-app-download
Power up the Camera until you hear the voice prompt “Camera is ready for Wi-Fi configuration’’, (expected within 1 minute).
Click + to add the camera and select the “QR Scan Configuration” for WiFi connection.
FIRST USE
Click on the device on the device page to enter the device control page and set the printer model
*Click on the corresponding space to perform the operation.
Use a USB cable to connect the.
Camera to the printer USB port “After the printer s started (when the printer screen is operable, th printer is considered to have completed the startup).
Connect the Camera by clicking the “connect” button to connect the printer.
*After successful connection, the button will change to “Disconnect”. Also, Prnt off only indicatos that there is no current printing process
Click “+’, upload the G-code file, and click “{print icon}” to start printing.
*If your printer is an automatic bed leveling printer, please insert M420 $1 below G28 in the Star Goodo section of your siicing software to enable automatic bed leveling compensation
On the dashboard page or device page, you can monitor the progress of the printer’s printing task and pause or stop the printing operation.
WEB PAGE
In the Beagleprint app, click on Settings, find the IP address in the Camera information page, and use a browser to enter tto access the login page.
“The Camera is connected 1o the same network (same subnet) s the ‘Gomputer/tablet/phone using the browsor.
Once logged in successfully, you can connect to the printer via the *Connect” button in the upper left corner.
“Ifit says “Disconnoct, it moans the camora has been connected to the printor
Then, on the Dashboard page, find “Printable Files List”, click “Upload”, select the G-code file to be uploaded, and click the 
to start printing.
“If your printer is an automalic bod leveling printer, please insert M420 S1 below G283 in the Star Geode section of your slicing software fo enable aufomatic bed leveling compensation.
On the Dashboard page, find the Status & Control” page, where Yyou can monitor the printing progress, such as the number of layers and height, and pause or cancel printing as needed
CUSTOMER SUPPORT
 https://mintion-6288.myshopify.com/blogs/guidelines |
 https://www.facebook.com/groups/mintion |
| Please visit the Mintion official website for more machine usage and maintenance tutorials: | Join our Facebook group to communicate with us, our users, fans, and other members through Facebook. |
If you need human assistance, you can email: support@mintion.net and we will contact you within 24 hours
ATTENTION
Please DO NOT cut offthe power of the Beagle V2 camera when it’s connecting to the 3d printer on printing; DO NOT disconnect the camera from the printer when it is connectad to the printer and transmit geode files through the camera for printing. Otherwise, it will cause printing failure and damage the camera’s firmware. In this case, the camera cannot work typically; this problem is the user problem, not a quality problem. Hence, please ensure that you cannot disconnect the camera from the power supply and the USB cable connected to the printer when the camera is working, and the 3d printer is printing.
The Beagle camera only supports one printer connection for control, allowing four users to simultaneously log in and access the camera (including mobile phone and computer users). Therefore, please make sure s securely accessing the device to prevent bad guys from accessing the camera or printer and the environment to cause damage
Atthe same time, we recommend that you do not let the 3d printer perform the 3d printing work completely unattended. Please come to the printer and watch the real printing progress of the printer regularly to prevent further deterioration of the situation when an abnormal condition occurs.
This camera shortens the distance between the user and the printer. The user is obliged to ensure the reasonableness and legality of the use of the product and avoid infringement of third-party rights, including but not limited to publicity rights, intellectual property rights, data rights, or privacy rights. At the same time, since the customers’ use and storage of this camera are beyond our control, we are not responsible for possible personal injury or property loss.
This manual is for reference only. In any case, we have the right to modify and improve it without notifying users. If you want to know the latest instruction manual, you can go to the official website for more information.
FCC WARNING STATEMENT
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular instalation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:ealer or an experienced radio/TV technician for help.
- Reorient or relocate the receiving antenna.
- Increass the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RADIATION EXPOSURE STATEMENT
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co – located for operating in conjunction with any other antenna or transmitter.
SPECIFICATION
| Model | Beagle V2 |
| Video Compression | H.264/MJPEG |
| Video Resolution | 1080P |
| Night Version | Yes |
| Frame Rate | Upto 25fps |
| Auto Time-lapse Video | Yes |
| WiFi Connectivity | Supports 2.4GHz/5GHz |
| Compatibility | Marlin 3D Printers |
| Connect to Printer | USB Cable |
| Files Storage | Micro SD Card |
| Power Source | Plug-in |
| Lens Adjustable | Manual Knob |
| 1/4” Screw for Tripod | Yes |
www.mimtion.net
SHENZHEN MINTION TECHNOLOGY CO., LTD
Distribution: sales@mintion.net
Support: support@mintion.net
Facebook Group: Mintion Official Group
Documents / Resources
 |
Mintion Upgraded 3D Printer Camera [pdf] User Manual Upgraded 3D Printer Camera, Upgraded 3D, Printer Camera, Camera |