MICROCHIP AN4323 PD69200 to PD69220 Conversion
Introduction
This application note provides guidelines for using the PD69220 device on a Printed Circuit Board (PCB) that was designed for the PD69200 device. The following aspects must be considered:
- Host–PoE controller communication management
- UART or I2C address selection
- PCB footprint
- Solder paste mask
Using the 16-byte communication protocol, this application note also defines a method to determine which PoE controller (PD69200 or PD69220) is installed on a switch.
- Solder paste mask
Host–PoE Controller Communication Management
The following figure and table show that UART (set to 19200 bps) or I2C (up to 400 KHz) communication between the host CPU and PoE controllers are managed by setting the PD69220/PD69220 address pin number 22 (I2C_ADDR)
Figure 1-1. PD69200/PD69220 Communication Management
The following table lists the specific value of R to choose UART or I2C and to set the address.
Table 1-1. Serial Communication Configuration
| I2C Address Hexadecimal | R1–KΩ (1%) | |
| PD69200 | PD69220 | |
| UART | N.C. | N.C. |
| 0x4 | 97.6 | 147 |
| 0x8 | 53.6 | 86.6 |
| 0xC | 35.7 | 57.6 |
| 0x10 | 25.5 | 43.2 |
| 0x14 | 19.1 | 34 |
| 0x18 | 14.7 | 26.7 |
| 0x1C | 11.3 | 22.1 |
| 0x20 | 8.87 | 18.2 |
| 0x24 | 6.81 | 15.4 |
| 0x28 | 5.23 | 13 |
| 0x2C | 3.92 | 11 |
| 0x30 | 2.80 | 9.31 |
| 0x34 | 1.87 | 7.87 |
| 0x38 | 1.02 | 6.49 |
| 0x3C | 0.324 | 5.49 |
Note: All other parameters of resistor R1 (size, power, footprint, and so on) are the same in all the controllers, except in the value.
PD69200 QFN vs. PD69220 LGA Package
The PD69200 device is packaged in a 32 pin 5 mm × 5 mm QFN package and the PD69220 device is packaged in a 32 pin 5 mm × 5 mm LGA. The pinout of the two devices are identical. However, there are physical differences in
the thermal pad and pins. Additionally, there are differences in the physical package construction of the QFN vs. LGA. Due to these differences, while using the PD69220 device on a PCB that was designed for the PD69200, the paste mask or stencil must be optimized for use with the PD69220 device.
Section 3. PCB Footprint gives recommendations for a revised stencil for PD69220, if the original PCB used the footprint for PD69200 that was recommended in the PD69200 data sheet. If the footprint in the PD69200 data sheet is not used, follow the general principles outlined in section 3. PCB Footprint to optimize the stencil based on the footprint that was used.
See the PD69220 Data Sheet for a footprint recommendation if the design is a new PCB that was designed for the PD69220 unit.
Package Construction
This section provides a general overview of the physical differences between the PD69200 QFN and the PD69220 LGA
PD69200 QFN
The PD69200 physical silicon die is mounted directed on a copper lead frame. The IC and lead frame are encapsulated in plastic. In this case, the bottom surface is plastic and the ePad and copper pin features extrude (stick out) from the plastic surface by the dimension A1 (a maximum of 0.05 mm). See the following figure.
Figure 2-1. PD69200 QFN Construction
PD69220 LGA
To make the PD69220 pinout identical to PD69200, an interposer or “small PCB” is used in the package construction. The PD69220 physical silicon die is mounted onto the interposer. The interposer routes to the package pins in such
a manner that the pinout between PD69200 and PD69220 is identical. The interposer and die are encapsulated in plastic. The bottom surface of the package is the solder mask associated with the interposer.
Due to this construction, the ePad and pins, rather than extruding from the package surface, are actually recessed into the package surface (like a cave) by the thickness of the solder mask.
The ePad and pins are copper electroplated with nickel-gold.
See the following figure
ePad
Figure 2-1 and Figure 2-2 show the difference in the ePad construction. The PD69220 ePad is a single 3.5 mm × 3.5 mm square, whereas ePads in the PD69200 device are nine 0.6 mm × 0.6 mm squares.
The nine squares are electrically connected to each other.
Pins
The following table lists the dimensions for PD69200 and PD69220 pins.
Table 2-1. Pin Dimensions
| Device | Dimension | Minimum (mm) | Nom (mm) | Maximum (mm) |
| PD69200 | Length (L) | 0.30 | 0.40 | 0.50 |
| Width (b) | 0.18 | 0.25 | 0.30 | |
| PD69220 | Length (L) | 0.30 | 0.35 | 0.40 |
| Width (b) | 0.20 | 0.25 | 0.30 |
Wettable Flanks
There is no copper on PD69220 package side and it does not have a wettable flank. While the PD69200 unit does have a copper feature on the package side, no effort is taken to prevent oxidation. Therefore, this package is also considered to not have a wettable flank.
See the following figure
PCB Footprint
Microchip has provided a recommended footprint for PD69220 in the device datasheet and in this document. These recommendations apply when the Microchip recommended footprint for PD69200 is used on the PCB and the customer is mounting a PD69220 using the footprint designed for the PD69200 device.
If the customer has used an alternate footprint for the PD69200 device, then the general principles discussed must be applied to develop an optimized stencil based on the actual PD69200 footprint used
PD69200 Package Outline Drawing
The following figure shows the package outline drawing of the PD69200 device.
Note: For the most current package drawings, see the Microchip Packaging Specification located at www.microchip.com/packaging
Figure 3-1. PD69200 Package Outline Drawing (32 Pin QFN 5 mm × 5 mm)
The following table lists the dimensions and measurements of the PD69200 package.
Table 3-1. PD69200 Package Outline Dimensions and Measurements
| Dimension | Millimeters | Inches | ||
| Min. | Max. | Min. | Max. | |
| A | 0.80 | 1.00 | 0.031 | 0.039 |
| A1 | 0.00 | 0.05 | 0 | 0.002 |
| e | 0.50 BSC | — | 0.02 BSC | — |
| L | 0.30 | 0.50 | 0.012 | 0.02 |
| b | 0.18 | 0.30 | 0.007 | 0.012 |
| D2 | 3.50 | 3.70 | 0.138 | 0.147 |
| E2 | 3.50 | 3.70 | 0.138 | 0.147 |
| D | 5.00 BSC | — | 0.197 BSC | — |
| E | 5.00 BSC | — | 0.197 BSC | — |
PD69220 Package Outline Drawing
The following figure shows the package outline drawing of the PD69220 device.
Note: For the most current package drawings, see the Microchip Packaging Specification located at www.microchip.com/packaging
Figure 3-2. PD69220 Package Outline Drawing (32-Pin LGA 5 mm × 5 mm)
The following table lists the dimensions and measurements of the PD69220 package.
| Dimension | Millimeters | ||
| Min. | Typ. | Max. | |
| A | — | — | 1 |
| A1 | — | 0.21 | — |
| A2 | — | 0.7 | — |
| D | — | 5 | — |
| E | — | 5 | — |
| W | 0.2 | 0.25 | 0.3 |
| L | 0.30 | 0.35 | 0.4 |
| e | — | 0.5 | — |
| n | — | 32 | — |
| D1 | — | 3.5 | — |
| E1 | — | 3.5 | — |
| SD | — | 0.25 | — |
| SE | — | 0.25 | — |
Recommended PCB Layout
The following figures show the recommended PCB layout patterns for the 32-pin QFN 5 mm × 5 mm PD69200 and the change to the stencil required for the 32-pin LGA 5 mm × 5 mm PD69220, to use this footprint. Units are in millimeters.
Figure 3-3. PD69200 Solder Mask
Figure 3-4. PD69200 Top-Layer Copper
Figure 3-6. PD69220 Paste Mask
Identification of PoE Controller
This section describes how to determine if PD69200 or PD69220 is installed on a switch. There are two cases to consider:
- Under normal operation where valid firmware is installed
- Under a fault condition where the firmware installed in the controller has become corrupted
Under Normal Operation
In order to identify which PoE controller is assembled, execute the command “Get Software Version”, as described in section 4.1.19 of the PD692x0 Communication Protocol User Guide or section 3.1.17 of the PD692x0 BT Serial Communication Protocol User Guide. These documents can be found in the Microchip Software Library.
The response from the PoE controller includes the Prod#, which indicates the PoE controller type.
Table 4-1. Get Software Version
In order to identify which PoE controller is assembled, execute the command “Get Software Version”, as described in section 4.1.19 of the PD692x0 Communication Protocol User Guide or section 3.1.17 of the PD692x0 BT Serial Communication Protocol User Guide. These documents can be found in the Microchip Software Library.
The response from the PoE controller includes the Prod#, which indicates the PoE controller type.
Table 4-1. Get Software Version
| [0]
KEY |
[1]
ECHO |
[2]
SUB |
[3]
SUB1 |
[4]
SUB2 |
[5]
DATA |
[6]
DATA |
[7]
DATA |
[8]
DATA |
[9]
DATA |
[10]
DATA |
[11]
DATA |
[12]
DATA |
| 0x02 | ## | 0x07 | 0x1E | 0x21 | 0x4E | 0x4E | 0x4E | 0x4E | 0x4E | 0x4E | 0x4E | 0x4E |
| Request | — | Global | Version | SW
Version |
N | N | N | N | N | N | N | N |
| 0x03 | ## | Val | 0x4E | Val | Val | Val | Val | Val | Val | |||
| Telemetry | — | HW
Version |
N | Prod# | SW_Version | Param# | Build# | Internal SW# | 0x0000 | |||
Table 4-2. Product Number
| Product Number (Decimal) | PoE Controller Type |
| 22 | PD69200 programmed with IEEE® 802.3at firmware |
| 24 | PD69200 programmed with IEEE 802.3bt firmware |
| 27 | PD69210 programmed with IEEE 802.3at firmware |
| 26 | PD69210 programmed with IEEE 802.3bt firmware |
| 28 | PD69220 programmed with IEEE 802.3at firmware |
| 29 | PD69220 programmed with IEEE 802.3bt firmware |
Under a Fault Condition
Use the following procedure to identify which PoE controller is installed on a PCB in the case of a fault condition when the firmware is corrupted.
When CPU_Status1_Err field reports on firmware error (bit 1 = ‘1’), the telemetry structure changes to the following.
Table 4-3. Telemetry at Bootup Error
| [0]
KEY |
[1]
ECHO |
[2]
SUB |
[3]
SUB1 |
[4]
SUB2 |
[5]
DATA |
[6]
DATA |
[7]
DATA |
[8]
DATA |
[9]
DATA |
[10]
DATA |
[11]
DATA |
[12]
DATA |
| 0x03 | 0xFF | Val | 0x4E | 0x4E | Val | Val | Val | Val | 0x4E | 0x4E | 0x4E | 0x4E |
| Telemetry | — | CPU
Status1 Err |
N | N | Err Code | Err Info1 | Err Info2 | Download Type | N | N | N | N |
The following table lists the fields description in case of an error.
Table 4-4. Error Type
| Err Name | Err Code | Err Info1 | Err Info2 | Download Type |
| Need Download PD69200 | 0x4E | 0x4E | 0x4E | 0x4E |
| Need Download PD69210/220 | 0x4E | 0x4E | 0x4E | 0x33 |
| HW error Try to program PD69210 or PD69220 with PD69200 firmware | 0x02 | CPU Type Boot 0x33 | CPU Type App 0x2C | 0x33 |
| HW error Try to program PD69200 with PD69210 or PD69220 firmware | 0x02 | CPU Type Boot 0x2C | CPU Type App 0x33 | 0x4E |
| Sys Type error from APP Try to program PD69210 with PD69220 firmware |
0x03 | Boot Sys Type 0x40 | App Sys Type 0x41 | 0x4E |
| Sys Type error from APP
Try to program PD69220 with PD69210 firmware |
0x03 | Boot Sys Type 0x41 | App Sys Type 0x40 | 0x4E |
Revision History
| Revision | Date | Description |
| C | 07/2022 | The following is the summary of changes made in this revision:
|
| B | 06/2022 |
|
| A | 12/2021 | Initial Revision |
Microchip Information
The Microchip Website
Microchip provides online support via our website at www.microchip.com/. This website is used to make files and information easily available to customers. Some of the content available includes:
- Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software
- General Technical Support – Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip design partner program member listing
- Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
Product Change Notification Service
Microchip’s product change notification service helps keep customers current on Microchip products. Subscribers will receive email notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest.
To register, go to www.microchip.com/pcn and follow the registration instructions.
Customer Support
Users of Microchip products can receive assistance through several channels:
- Distributor or Representative
- Local Sales Office
- Embedded Solutions Engineer (ESE)
- Technical Support
Customers should contact their distributor, representative or ESE for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in this document. Technical support is available through the website at: www.microchip.com/support
Microchip Devices Code Protection Feature
Note the following details of the code protection feature on Microchip products:
- Microchip products meet the specifications contained in their particular Microchip Data Sheet.
- Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and under normal conditions.
- Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.
- Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not mean that we are guaranteeing the product is “unbreakable”. Code protection is constantly evolving. Microchip is committed to continuously improving the code protection features of our products.
Legal Notice
This publication and the information herein may be used only with Microchip products, including to design, test, and integrate Microchip products with your application. Use of this information in any other manner violates these terms. Information regarding device applications is provided only for your convenience and may be superseded by updates.
It is your responsibility to ensure that your application meets with your specifications. Contact your local Microchip sales office for additional support or, obtain additional support at www.microchip.com/en-us/support/design-help/client-support-services. THIS INFORMATION IS PROVIDED BY MICROCHIP “AS IS”. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, OR WARRANTIES RELATED TO ITS CONDITION, QUALITY, OR PERFORMANCE. IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE INFORMATION OR ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP’S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THE INFORMATION.
Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
AgileSwitch, APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, Flashtec, Hyper Speed Control, HyperLight Load, Libero, motorBench, mTouch, Powermite 3, Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet- Wire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub, TimePictra, TimeProvider, TrueTime, and ZL are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky, BodyCom, Clockstudio, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, Espresso T1S, EtherGREEN, GridTime, IdealBridge, In-Circuit Serial Programming, ICSP, INICnet, Intelligent Paralleling, IntelliMOS, Inter-Chip Connectivity, JitterBlocker, Knob-on-Display, KoD, maxCrypto, maxView, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, RTAX, RTG4, SAMICE, Serial Quad I/O, simpleMAP, SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI, SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total Endurance, Trusted Time, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY, ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage Technology, and Symmcom are registered trademarks of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their respective companies.
© 2022, Microchip Technology Incorporated and its subsidiaries. All Rights Reserved. ISBN: 978-1-6683-0962-9
Quality Management System
For information regarding Microchip’s Quality Management Systems, please visit www.microchip.com/quality.
Worldwide Sales and Service
| Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: www.microchip.com/support Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423] Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-400 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-960 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada – Toronto Tel: 905-695-1980 Fax: 905-695-2078 |
Australia – Sydney Tel: 61-2-9868-6733 China – Beijing Tel: 86-10-8569-7000 China – Chengdu Tel: 86-28-8665-5511 China – Chongqing Tel: 86-23-8980-9588 China – Dongguan Tel: 86-769-8702-9880 China – Guangzhou Tel: 86-20-8755-8029 China – Hangzhou Tel: 86-571-8792-8115 China – Hong Kong SAR Tel: 852-2943-5100 China – Nanjing Tel: 86-25-8473-2460 China – Qingdao Tel: 86-532-8502-7355 China – Shanghai Tel: 86-21-3326-8000 China – Shenyang Tel: 86-24-2334-2829 China Shenzhen Tel: 86-755-8864 2200 China – Suzhou Tel: 86-186-6233 1526 China – Wuhan Tel: 86-27-5980 5300 China – Xian Tel: 86-29-88337252 China – Xiamen Tel: 86-592 2388138 China – Zhuhai Tel: 86-756 3210040 |
India – Bangalore Tel: 91-80-3090-4444 India – New Delhi Tel: 91-11-4160-8631 India – Pune Tel: 91-20-4121-0141 Japan – Osaka Tel: 81-6-6152-7160 Japan – Tokyo Tel: 81-3-6880- 3770 Korea – Daegu Tel: 82-53-744 4301 Korea – Seoul Tel: 82-2-554-7200 Malaysia – Kuala Lumpur Tel: 60-3-7651-7906 Malaysia – Penang Tel: 60-4-227-8870 Philippines – Manila Tel: 63-2-634 9065 Singapore Tel: 65-6334-8870 Taiwan – Hsin Chu Tel: 886-3-577-8366 Taiwan – Kaohsiung Tel: 886-7-213-7830 Taiwan – Taipei Tel: 886-2-2508-8600 Thailand – Bangkok Tel: 66-2-694-1351 Vietnam – Ho Chi Minh Tel: 84-28-5448-2100 |
Austria – Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark – Copenhagen Tel: 45-4485-5910 Fax: 45-4485-2829 Finland – Espoo Tel: 358-9-4520-820 France – Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30 90-79 Germany – Garching Tel: 49-8931-9700 Germany – Haan Tel: 49-2129-3766400 Germany – Heilbronn Tel: 49-7131-72400 Germany -Karlsruhe Tel: 49-721-625370 Germany -Munich Tel: 49-89-627-144- Fax: 49-89-627-144-44 Germany – Rosenheim Tel: 49-8031-354-56 Israel – Ra’anana Tel: 972-9-744 7705 Italy – MilanTel: 39-0331-742611 Fax: 39-0331-466781 Italy – Padova Tel: 39-049-7625286 Netherlands – Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway – Trondheim Tel: 47-72884388 Poland – Warsaw Tel: 48-22-3325737 Romania – Bucharest Tel: 40-21-407-87-50 Spain – Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden – Gothenberg Tel: 46-31-704-60-40 Sweden – Stockholm Tel: 46-8-5090-4654 UK – Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 |
Documents / Resources
 |
MICROCHIP AN4323 PD69200 to PD69220 Conversion [pdf] Owner's Manual AN4323, AN4323 PD69200 to PD69220 Conversion, PD69200 to PD69220 Conversion |
