Micro-Pointer WT10 Wireless Signal Detector User Manual

User Manual

WT10 Wireless signal detector

This product is the world’s first real-time digital wireless signal detection and analysis equipment aiming at Tracker (GSM signal) and wireless signal eavesdropping eavesdropping camera (WIFI signal). Independently developed, comprehensively optimized the wireless communication system, communication protocol and WIFI communication data packets of locators at home and abroad to realize the positioning of wireless signal equipment with high precision and accuracy.

Product introduce

1.1 Product Function:

• The location of the 50MHz-8GHZ wireless device can be detected.
• Mobile phone positioning in the cal.
• Mobile phone positioning in traffic consumption.
• You can find GSM plug-in bugs, snaps, and trackers.
• You can find the WiFi camera.
• Can detect sleep tracker.

1.2 Product Features:

• Simple operation, small and portable, flexible use occasions .
• 50 mHz-8 GHz wireless spectrum detection, covering all currently used wireless communication frequency bands.
• Can work continuously and continuously, connect with mobile phone software through data cable, and can record the signal and signal strength at all time points within 24 hours.
• Double horn work, different signal sources can be judged by different sounds.
• Scan speed 60us (microseconds) to ensure that all wireless signals are captured in real time.
• Signal strength distinguish 16 segments to effectively confirm the signal strength and distance of the transmitting signal source.
• The detection sensitivity is divided into two sections, ranging from 10cm to 10 m.
  Wide-Area detection and precise positioning.
• Mobile APP display detection.
• Can detect shutdown with strong magnetic tracker.
• 50MHz-8GHz adopts continuous compression technology, which can provide high measurement accuracy in a wide input frequency range, reaching a dynamic range of -68 dBm.Alarmmode: mute and beep.
• Based on the user’s usage scenario, multiple work scenario modes are innovatively developed to facilitate user use according to specific circumstances.

1.3 Product Standards：

1.4 Detection frequency range and corresponding protocol：

1.5 Applicable groups：

• Can detect shutdown with strong magnetic tracker.
• People who often use bank cards.
• People on business trip who take the hotels as home.
• Beautiful ladies who get easily photographed secretly.
• People who often go to public entertainment places .
• People who often go to various shopping malls to try on.
• People who respect personal privacy and others.
• People who contact and keep trade secrets.
• Security personnel in trade secrets and technical secrets sites.
• Anti-eavesdropping professionals.

1.6 Scope of application:

• To detect whether your car or office is installed with wireless eavesdroppers or wireless eavesdroppers.
• To detect whether the mobile phone is eavesdropped or abnormal (sending out signals for no reason during standby).
• To detect whether your car is installed with a GPS tracking listener and a GPS positioning tracker.
• To test whether your working environment and residential buildings have radiation from the base station on the roof.
• To detect SMS sending and receiving signals, mobile Internet signals, mobile phone switches and call signals.
• To detect the strong field of wireless network signal, mobile phone base station signal and wireless monitoring system.
• To detect whether house hold electric appliances such as microwave ovens leak electromagnetic radiation that is harmful to human body.
• To detect whether there is strong radiation called “mobile phone killer” in the environment.
• To detect whether there are suspicious radio signals in the environment.
• To detect more hidden 5.8GHz wireless camera sneak shooting, wireless eavesdropping, wireless monitor signal.
• Check the hotel, restroom, hotel, Entertainment Place, locker room wireless pinhole camera.
• Business negotiation, school invigilation sites, factories, military facilities or government agencies anti-theft photography eavesdropping.
• Withdraw money from AMMachine, cinema, concert, art gallery or museum, etc.
• To detect whether there is electromagnetic radiation that is harmful to human health while buying a house.
• To detect wireless signal jammers nearby.

Operation instructions

2.1 Product appearance:

2.2 Device Interface:
2.2.1 mode 1 (full-band detection): illustration 1

2.2.2 Mode 2 (Locator detection): illustration 2

2.2.3 Mode 3 (wireless camera detection): illustration 3

2.2.4 mode 4 (detection with strong magnetic locator): illustration 4

2.2.5 Mode 5 (mobile APP) connect mobile phone via data cable: illustration 5

Usage

3.1 The current usage of this equipment is as follows:
a), Long press the PSU switch (POWER) for 3 seconds. After hearing the sound of “Bi”, loosen your finger. The “Full Band Detector” indicator light is on. The default Full-Band 50MHz-8GHz detection mode is enabled when starting up. The left SM seat (ANT1) receiving terminal is enabled by default. The two antennas can be installed at will according to your own needs.
b), Short Press (MODE) to switch the working MODE. There are four modes to switch.
c), Long Press (MODE) to switch to Mute MODE. Mute MODE the Mute light is always on (remove Mute MODE and long press again).
d), Short Press (RANGE) can adjust the sensitive HIGH and LOW. There are two gears: HIGH and LOW.
e), Plug in the signal data cable and connect To the mobile APP. The display screen will turn off automatically after 10 seconds. At the same time, the Aux To APP light is always on.
3.2 According to data transmission mode to distinguish pinhole cameras：
3.2.1 According to the data transmission mode, it is divided into wireless and wired. The so-called wireless “pinhole” is composed of the principle of a camera and a receiver. The Two send and receive video signals wirelessly. Even if the camera is found, there is no one to steal the camera, so it is used most. Due to many occasions, the Canary photographers are unwilling to risk returning the downloaded data, so in the hotel, bathroom and other environments, wireless pinhole cameras are the main ones.
3.2.2 Common Position of pinhole cam
In the environment of the hotel and bedroom, the purpose of illegal people’s purpose is often the personal privacy that people care most about, mainly aiming at the bed of the hotel or bedroom. In the environment of the hotel, the shooting is carried out for a long time, and the target of the candid shooting is not fixed. In order to get the electricity conveniently, all kinds of pinhole cameras are often hidden in all kinds of hidden positions which are convenient to get the electricity, such as socket holes, screws, televisions and TV boxes, routers, smoke probes, etc. on the wall, aiming at the bed for shooting. In the bedroom environment, due to the strong timeliness and purpose of shooting, the target of stealing shooting is accurate, and there is no need to take electricity for a long time. Therefore, various cameras are often hidden in various simulated objects that are convenient to move, such as charger, hygrometer, doll’s eyes, clock, can, pen, watch and other items.
3.3 Classification of locators:
Wiring locator and wiring-free locator; It can also be divided into real-time locator and dormant locator and standby locator; Dormant locator can also be divided into motion work and dormant locator; Locator can also be divided into dual-mode (base station) locator and single-mode (base station) locator; Locator can also be divided into satellite locator and mobile phone base station locator; Satellite locator can also be divided
3.4 FAQ

1. Why is silent sleep tracker not detected?
   Answer: the commonly used sleep locator works once a day and only works for 5-7 minutes at a time, so the detector.
   When the wireless signal is being detected, the locator may not send a signal.
2. Why is the location of the real-time locator not accurately detected?
   Answer: The real-time locator usually sends a signal every 10 seconds. Please do not move back and forth during Detection. It is best.
   Fixed at one position for more than 5 minutes, and then changed to another position to continue the detection.
3. Why is the detector terminal “Didi” screaming?
   Answer: First, please clean up the surrounding environment, because there are too many interference signals around and too strong. Second, lower the sensitivity.
4. Why the detector beside the window of the House is particularly loud?
   Answer: The window is made of aluminum alloy, which forms a loop antenna and receives signals very well.
5. Why is the camera not detected?
   A: Maybe the camera is not working, or the camera is wired.

Mobile APP download address:

https://www.pgyer.com/4c5CLi3u