MHIGT M-CTR100 AI Pointer User Manual

MHIGT M-CTR100 AI Pointer

PRODUCT LIST

Start to Use

Step 1

Receiver Installation Instructions
Place the receiver with the front arrow facing up according to the installation prompt instructions. If placed above the TV, fix it by means of a clip. (As shown in Figure 1)

If placed underthe TV, it should be fixed by magnetic attraction. If the TV cannot be directly attached, a magnetic sheet needs to be attached to the intended location of the TV, and then the receiver should be fixed by magnetic attraction. (As shown in Figure 2)

Step 2
Plug the USB interface of the receiver into the USB port of the computer, and connect the computer to the  projector or smart TV

step 3
Turn the power button on the left side of the A1 pointer to the ON icon to start the demonstration pen. The indicator light at the top will light up green

Step 4
Switch the mode button on the right side of the A1 teaching stick to the corresponding computer system. For Windows, switch it to the bottom; for Apple Mac Os, switch it to the top

After the above steps are completed, the product starts to work normally

Key function description

Introduction to the button functions of the A1 pointer

Remark
Microsoft Office software does not support the quick functions of the spotlight and magnifying glass. Mac office software does not support the quick functions of Spotlight, magnifying glass, and digital laser

Indicator light status description

receiver

FCC Caution

Any Changes or modifications not expressly approved by the party Responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the   equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
For Al Pointer ( M-CTR100), this equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For Receiver(M-CTR101), this equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body.UWB devices may not be employed for the operation of toys. Operation onboard an aircraft, a ship, or a satellite is prohibited.

This equipment may only be operated indoors. Operation outdoors violates 47 U.S.C. 301 and could subject the operator to serious legal penalties.

Troubleshooting

• AIPointer not responding:
  • Ensure the power button is in the ‘ON’ position and the indicator light is green.
  • Check the battery level. If the red light is on constantly, the battery is low and needs charging.
  • If the red light is blinking, a system error has occurred. Try restarting the device.
• Receiver not connecting:
  • Ensure the receiver is properly plugged into a USB port on the computer.
  • Check the receiver’s blue light. If it’s flashing, it’s a pending connection. If it’s off, there might be a power or connection issue.
• Pointer functions not working correctly:
  • Verify that the system mode switch (Windows/Mac) on the AIPointer matches your computer’s operating system.
  • If using Microsoft Office on Windows or Mac Office on Mac, note that some quick functions (spotlight, magnifying glass, digital laser on Mac) are not supported.
• Interference issues:
  • Reorient or relocate the receiving antenna (receiver).
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FAQs

• Q: What is included in the AIPointer package?
  • A: The package includes the AIPointer (M-CTR100), Receiver (M-CTR101), Charging Cable, and a Portable Bag.
• Q: How do I know if my AIPointer is charging?
  • A: When charging, the red light on the AIPointer will remain on constantly. Once fully charged, the white light will remain on constantly.
• Q: Can I use the AIPointer with both Windows and Mac computers?
  • A: Yes, the AIPointer has a mode switch to select between Windows and Mac systems. However, please note that some quick functions (spotlight, magnifying glass, and digital laser on Mac) are not supported by Microsoft/Mac Office software.
• Q: What should I do if the receiver’s blue light is flashing?
  • A: A flashing blue light on the receiver indicates that it is in a pending connection status. Ensure the AIPointer is powered on and in the correct system mode.
• Q: Is it safe to use the AIPointer outdoors?
  • A: No, this equipment may only be operated indoors. Operation outdoors violates 47 U.S.C. 301 and could subject the operator to serious legal penalties.
• Q: What is the recommended distance between the AIPointer/Receiver and my body?
  • A: This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.