E-CSF Series Occupancy Sensor Remote Control
“
Product Information
Specifications
- Remote Control Model: MH01
- Mounting Heights: 3m, 6m, 9m, 12m, 15m
- Distance Between Sensors: 0.4m, 0.4m, 0.6m, 0.8m
- Motion Sensor: Yes
Product Usage Instructions
Settings (Remote Control MH01)
ON/OFF: Press this button to switch the light
to constant on or off mode. The sensor is disabled in this
mode.
Reset: Press to revert all parameters to the
setting of the DIP switch.
Auto Mode: Press to activate the sensor.
Previous parameter settings are retained.
DIM Test: Press to test the dimming function.
The sensor will automatically dim and return to normal mode.
Test (2s)
The Test(2s) button is for factory testing purposes only. It
activates test mode with specific settings.
Scene Options
Adjust detection area, hold time, stand-by period, stand-by dim
level, and daylight sensor settings by pressing the corresponding
buttons. Latest settings remain valid.
FAQ
Q: How can I adjust the detection area and other
parameters?
A: Press the corresponding buttons on the remote control to
adjust the detection area, hold time, stand-by period, stand-by dim
level, and daylight sensor settings.
A: The Test(2s) button is for factory testing purposes only. It
activates test mode with specific sensor settings for testing.
“`
8
8
Settings (Remote Control MH01)
Button
ON/OFF Reset Auto Mode
DIM Test
Remarks Press the “ON/OFF” button, the light goes to constant on or constant off mode, sensor is disabled. Press ” Reset ” or ” Auto Mode” button to quit from this mode.
Press “Reset” button, all parameters are same as setting of DIP switch.
Press “Auto Mode” button, the sensor starts to work and all parameter setting will be remained the same as the previous status before the light was switched on/off.
Press “DIM Test” button to test dimming function. Sensor will dim automatically and return to normal work mode.
Test (2s)
QS1
QS2
QS3
QS4
The button “Test(2s)” is for factory testing purpose only. The sensor will go to test mode, Detection sensitivity: 100% Hold time: 2sec
stand-by dim level:10% Stand-by period: 0s Daylight sensor: Disable Test mode can be quit by pressing any button.
scene Options
QS1
QS2 QS3
QS4
Detection Hold Stand-by Stand-by Daylight
Area
Time period dim level Sensor
100% 30s 1min
10% 5Lux
100% 1min 3min
10% 10Lux
100% 5min 10min 10% 30Lux
100% 10min 30min 10% Disable
Note: Detection area / Hold time /Stand-by period / Stand-by dim level / Daylight sensor can be adjust by pressing corresponding button. The latest setting stays in validity.
ON/OFF QS1 25% 5s
Reset
Auto Mode
Quick Setting
QS2
QS3
Detection Area
50%
75%
Hold Time
30s
1min
DIM Test QS4 100% 3min
5min 10% 0s
10min 20min
Stand-by DIM Level
20%
30%
Stand-by Period
10s
1min
30min 50% 3min
5min 5Lux
10min 30min
Daylight Sensor
15Lux
30Lux
+
50Lux
100Lux
150Lux
Disable
Test (2s)
R
As the control angle of the Infrared Remote Control is fixed (15°), if sensors are installed too close to each other, settings of both sensors will be configured. Please refer to the below chart for the distance of the installation of the sensor:
Mounting height 15m 12m 9m 6m 3m
istance between sensors m .4m .4m .6m .8m
Motion sensor
7.5° 7.5°
Motion sensor
ON/OFF QS1 25% 5s
Reset
Auto Mode
Quick Setting
QS2
QS3
Detection Area
50%
75%
Hold Time
30s
1min
DIM Test QS4 100% 3min
5min 10% 0s
10min 20min
Stand-by DIM Level
20%
30%
Stand-by Period
10s
1min
30min 50% 3min
5min 5Lux
10min 30min
Daylight Sensor
15Lux
30Lux
+ 50Lux
100Lux
150Lux
Disable
Test (2s)
R
Documents / Resources
 |
merrytek E-CSF Series Occupancy Sensor Remote Control [pdf] Owner's Manual E-CSF Series, E-CSF Series Occupancy Sensor Remote Control, E-CSF Series, Occupancy Sensor Remote Control, Sensor Remote Control, Remote Control, Control |