Contents hide
1 MEAN WELL RST-15K-HV 15KW Input With High Voltage Output
2 Features
2.1 Applications
3 SPECIFICATION
3.1 Function Manual
3.2 Mechanical Specification
4 Documents / Resources
4.1 References
5 Related Posts

meanwell-logo

MEAN WELL RST-15K-HV 15KW Input With High Voltage Output

MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-product-image

 

Features

  • 3ψ 3-wire / △196~305VAC or 3ψ 4-wire / Y 340~530VAC
  • High efficiency up to 94%
  • Forced air cooling
  • Output voltage and constant current level programmable
  • Wide voltage adjustment range 1~120%
  • Active current sharing up to 2 units(28.5KW)
  • Built-in remote ON-OFF control / Alarm signal
  • Protections: Short circuit / Overload / Over voltage / Over temperature / Fan fail
  • 5 years warranty
Applications

Energy & power system

  • U.V or laser diode application
  • Electrolysis system
  • Factory control or automation apparatus
  • Burn-in facility
  • RF application

·EV charging station

  • Description

RST-15K-HV is a 15KW 3ψinput enclosed type AC/DC power supply. This series operates for the wide range three phase AC input and offers the models with the high voltage DC output(115V/230V/380V) that mostly demanded from the industry. This series provides models with forced air cooling, that can be working at ambient temperature up to 70℃. Moreover, RST-15K-HV provides vast design flexibility by equipping various built-in functions such as the output programming, active current sharing, remote ON- OFF control, alarm signals.  etc.

  • Model Encoding
    MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-27

 

SPECIFICATION

MODEL RST-15K-115 RST-15K-230 RST-15K-380
OUTPUT DC VOLTAGE (factory default) 115V 230V 380V
CURRENT (factory default) 130A 64.8A 39.55A
CURRENT RANGE 0 ~ 130A 0 ~ 69A 0 ~ 45A
RATED POWER 14950W 14904W 15030W
FULL POWER VOLTAGE RANGE 115 ~ 138V 216 ~ 260V 334 ~ 400V
RIPPLE & NOISE (max.) Note.2 1Vp-p 2Vp-p 4Vp-p
VOLTAGE ADJ. RANGE 90 ~ 138V 170 ~ 260V 260 ~ 400V
Can be adjusted via built-in potentiometer
VOLTAGE TOLERANCE Note.3 ±1.0% ±1.0% ±1.0%
LINE REGULATION ±0.5% ±0.5% ±0.5%
LOAD REGULATION ±0.5% ±0.5% ±0.5%
SETUP, RISE TIME 3000ms, 200ms at full load
HOLD UP TIME (Typ.) 16ms 230VAC/400VAC at 75% load              10ms / 230VAC/400VAC at full load
INPUT VOLTAGE RANGE 3ψ 3W/△196~305VAC or 3ψ 4W/Y 340~530VAC
FREQUENCY RANGE 47 ~ 63Hz
POWER FACTOR (Typ.) ≧0.98/230VAC(400VAC)/≧0.97/277VAC(480VAC) at full load
EFFICIENCY (Typ.)              Note.7 93% 94% 94%
AC CURRENT (Typ.) 45A/230VAC(3ψ 3-wire / △)               26A/230VAC(3ψ 4-wire / Y)
INRUSH CURRENT (Typ.) 150A/230VAC(3ψ 3-wire / △)               100A/230VAC(3ψ 4-wire / Y)
LEAKAGE CURRENT <3.5mA/Y 530VAC  <21mA /△305VAC
PROTECTION  

OVERLOAD

 100 ~ 107% of rated current
Protection type : Constant current limiting, unit will shutdown after 5 sec. re-power on to recover
 

OVER VOLTAGE

 145 ~ 166V 273 ~ 312V 420 ~ 480V
Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down
FUNCTION CURRENT SHARING Up to 2 units. Please refer to the Function Manual
OUTPUT VOLTAGE PROGRAMMABLE Adjustment of output voltage is allowable between 1 ~ 120% of nominal output voltage. Please refer to the PV curve Function Manual
CONSTANT CURRENT LEVEL PROGRAMMABLE Adjustment of constant current level is allowable between 20 ~ 100% of rated current. Please refer to the Function Manual
REMOTE ON-OFF CONTROL Please refer to the Function Manual
ALARM SIGNAL OUTPUT AC fail, DC OK, fan fail, OTP. Please refer to the Function Manual.
ENVIRONMENT WORKING TEMP. -30 ~ +70℃ (Refer to “Derating Curve”)
WORKING HUMIDITY 20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY -40 ~ +85℃, 10 ~ 95% RH non-condensing
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 45℃)
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY & EMC

(Note 6,8)

 SAFETY STANDARDS UL62368-1, CAN/CSA C22.2 No. 62368-1, TUV BS EN/EN62368-1, EAC TP TC 004 approved
WITHSTAND VOLTAGE I/P-O/P:4.3KVDC  I/P-FG:2.8KVDC  O/P-FG:2.8KVDC
ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION Parameter Standard Test Level / Note
Conducted BS EN/EN55032 (CISPR32) / BS EN/EN55011 (CISPR11) Class B
Radiated BS EN/EN55032 (CISPR32) / BS EN/EN55011 (CISPR11) Class A
Harmonic Current BS EN/EN61000-3-12 —–
Voltage Flicker BS EN/EN61000-3-3 —–
EMC IMMUNITY BS EN/EN55024 , BS EN/EN61204-3, BS EN/EN61000-6-2
Parameter Standard Test Level / Note
ESD BS EN/EN61000-4-2 Level 3, 8KV air ; Level 2, 4KV contact
Radiated BS EN/EN61000-4-3 Level 3
EFT / Burst BS EN/EN61000-4-4 Level 3
Surge BS EN/EN61000-4-5 Level 4, 4KV/Line-Earth ; Level 3, 2KV/Line-Line
Conducted BS EN/EN61000-4-6 Level 3
Magnetic Field BS EN/EN61000-4-8 Level 4
Voltage Dips and Interruptions BS EN/EN61000-4-11 >95% dip 0.5 periods, 30% dip 25 periods,

>95% interruptions 250 periods
 

OTHERS

 MTBF 121.9K hrs min.         Telcordia SR-332 (Bellcore) ; 16.2K hrs min.          MIL-HDBK-217F (25℃)
DIMENSION 540*424*83.5mm (L*W*H)
PACKING 25Kg; 1pcs/25Kg/2.82CUFT
NOTE
  1. All parameters NOT specially mentioned are measured at △230VAC(Y 400VAC) input, rated load and 25℃ of ambient temperature.
  2. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
  3. Tolerance :includes set up tolerance, line regulation and load regulation.
  4. Derating may be needed under low input voltages. Please check the derating curve for more details.
  5. If use PV signal to adjust Vo, under creatin operation conditions, ripple noise of Vo might go over rating defined in this specification.
  6. Need additional EMI filter to meet regulations of EMC conducted and radiated emission. Characteristics of EMI filter please refer to the table, Minimum Insertion Loss.
  7. The efficiency is measured at △: 230VAC/Y: 400VAC input. The efficiency level is measured at output voltage 115V(115V model)/230V(230V model)/ 380V(380V model).
  8. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 600mm*900mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com)
  9. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
  10. An unstable O/P voltage is expected in the first 300ms after power on. A minimum load of 5% is suggested if fast load change is required at power on phase.
  11. Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

Block DiagramMEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-01DERATING CURVE MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-02

                                          STATIC CHARACTERISTICS                          EFFICIENCY VS LOAD (380V MODEL)MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-03

AC Power Connection
Fig 1.2
◎3ψ3-wire /△196~305VAC MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-04ψ 3 4-wire / Y 340~530VAC MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-05Note : RST-15K can also be operated by 1ψ2-wire 196~305VAC input. Please refer to the connection diagram below.
Operating with 1ψ2-wire may lead to certain characteristics different from the specification, such as the larger Ripple and Noise. Should there be any issues, please contact MEAN WELL. MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-06

Function Manual
  1. Output Voltage Programming (or, PV / remote voltage programming / remote adjust / margin programming / dynamic voltage trim)
    1. Default by potentiometer (SVR)
      • Have the DIP switch position-3 set as
      • Output voltage can be trimmed by SVR.
    2. By Output Voltage Programming
      • Have the DIP switch position-3 set as
      • The output voltage can be trimmed to 1~120% by applying EXTERNAL VOLTAGE between PV+ and PV- on CN26 or CN27.MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-07MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-08
      • The 100% output voltage is 115/216/334V.
      • When PV signal to adjust voltage under Vo<11.5V(115V model) / 21.6V(230V model) / 33.4V(380V model) with dynamic load condition, the Vo overshoot & undershoot might go over rating.MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-09
      • The rated current should change with the Output Voltage Programming accordingly.
      • Maximum output current is Based on rated power wattage.
  2. Constant Current Programming (or, PC / remote current programming / dynamic current trim)
    1. Default Overload Protection(OLP) 100~107% of rated current
      • Have the DIP switch position-2 set as
      • Output current is set default value.
    2. by Constant Current Level Programming
      • Have the DIP switch position-2 set as
      • The constant current level can be trimmed to 20~100% of the rated current by applying EXTERNAL VOLTAGE between PC+ and PC- on CN26 or CN27.

MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-10 MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-11EXTERNAL VOLTAGE (DC)
Fig 2.2

3. Select Overload Protection (OLP) Mode
(1) Default Continuous Constant Current mode
Have the DIPswitch position-1 set asMEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-12 ,and RST-15K will work in continuous constant current mode when the output is overloaded andthe output voltage is greater than 50% of the rated output voltage.

Delay Shutdown mode
Have the DIPswitch position-1 set asMEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-13 ,and RST-15K will shut down after 5 seconds of constant current operation, when the output is overloaded or short-circuited.

Remote ON-OFF Control

  • The power supply can be turned ON-OFF by using the “Remote ON-OFF” function.
    Between Remote ON-OFF(CN25 pin5) and 12V-AUX(CN25 pin1) Output Status
    Switch close (Short) power supply ON
    Switch open (Open) power supply OFF

    Table 4.1

MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-145. Alarm Signal Output
※ There are 4 alarm signals on CN22, and each signal can select two types of output circuit.
(1)Relay contact output {OTP1, OTP1-GND) ; (DC-OK1, DC-OK1-GND) ; (AC-FAIL1-GND, AC-FAIL1) ; (FAN-FAIL1-GND, FAN-FAIL1)} Normally open contact. “Short” when the alarm arises. Relay contact rating(maximum) is 30V/1A resistive.MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-15(2)Open collector output {DC-OK2-GND, DC-OK2) ; (AC-FAIL2-GND, AC-FAIL2) ; (OTP2, OTP2-GND) ; (FAN-FAIL2, FAN-FAIL2-GND)} An external voltage source is required for this function that is shown in Fig 5.2. These signals are isolated from output. The maximum sink current is 10mA and the maximum external voltage is 20V (there is a built-in 24V zener diode in inner circuitry).MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-166. Current Sharing
RST-15K has the built-in active current sharing function and can be connected in parallel, up to 2 units, to provide higher output power as exhibited below :
※ The voltage difference among each output should be minimized that less than 0.2V is required.
※ The total output current must not exceed the value determined by the following equation.
Maximum output current at parallel operation=(The rated current per unit)x(Number of unit)x0.95
※ When the total output current is less than 5% of the total rated current, or say (5% of Rated current per unit)×(Number of unit)
the current shared among units may not be fully balanced. MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-17CS+, CS- and RC+, RC- are connected mutually in parallel.

Mechanical Specification

MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-18Mounting Instruction

Hole No. Recommended Screw Size MAX. Penetration Depth L Recommended mounting torque
1 M4 5mm 7~10Kgf-cm

MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-19Control Pin No. Assignment CN26,CN27(): HRS DF11-06DP-2DS or equivalent 15

MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-20

Mating Housing HRS DF11-06DS or equivalent
Terminal HRS DF11-**SC or equivalent

CN26 and CN27 are connected internally.

Pin No. Function Description
1 CS- Current sharing signal. When units are connected in parallel, the CS pins of the units should be connected to allow current balance between units.
2 CS+
3 PC- Connection for output current programming.
4 PV- Connection for output voltage programming.
5 PC+ Connection for output current programming.
6 PV+ Connection for output voltage programming.

Control Pin No. Assignment CN22(): HRS DF11-16DP-2DS or equivalent 1 15

MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-21

Mating Housing HRS DF11-16DS or equivalent
Terminal HRS DF11-**SC or equivalent

 

Pin No. Function Description
1  

DC-OK1

 Alarm signal of DC-OK.

Normally open contact. “Short” when the PSU turns on. Relay contact rating(maximum) is 30V/1A resistive.
2 AC-FAIL1 Alarm signal of AC-fail.

Normally open contact. “Short” when the PSU input voltage is too low. Relay contact rating(maximum) is 30V/1A resistive.
 

3

  

DC-OK1-GND

 Alarm signal of DC-OK.

Normally open contact. “Short” when the PSU turns on. Relay contact rating(maximum) is 30V/1A resistive.
4 AC-FAIL1-GND Alarm signal of AC-fail.

Normally open contact. “Short” when the PSU input voltage is too low. Relay contact rating(maximum) is 30V/1A resistive.
5 DC-OK2 Alarm signal of DC-OK.
Open collector signal. Low when the PSU turns on. The maximum sink current is 10mA and the maximum external voltage is 20V.
6 AC-FAIL2 Alarm signal of AC fail.
Open collector signal. Low when the PSU input voltage is too low. The maximum sink current is 10mA and the maximum external voltage is 20V.
7 DC-OK2-GND Alarm signal of DC-OK.
Open collector signal. Low when the PSU turns on. The maximum sink current is 10mA and the maximum external voltage is 20V.
8 AC-FAIL2-GND Alarm signal of AC fail.
Open collector signal. Low when the PSU input voltage is too low. The maximum sink current is 10mA and the maximum external voltage is 20V.
9 OTP1 Alarm signal of OTP.
Normally open contact. “Short” when the PSU over temperature protection occurs. Relay contact rating(maximum) is 30V/1A resistive.
10 FAN-FAIL2 Alarm signal of fan fail.
Open collector signal. Low when the internal fan fails. The maximum sink current is 10mA and the maximum external voltage is 20V.
11 OTP1-GND Alarm signal of OTP.

Normally open contact. “Short” when the PSU over temperature protection occurs. Relay contact rating(maximum) is 30V/1A resistive.
12  

FAN-FAIL2-GND

 Alarm signal of fan fail.
Open collector signal. Low when the internal fan fails. The maximum sink current is 10mA and the maximum external voltage is 20V.
13 OTP2 Alarm signal of OTP.
Open collector signal. Low when the PSU over temperature protection occurs. The maximum sink current is 10mA and the maximum external voltage is 20V.
14 FAN-FAIL1 Alarm signal of fan fail.
Normally open contact. “Short” when the internal fan fails. Relay contact rating(maximum) is 30V/1A resistive.
15 OTP2-GND Alarm signal of OTP.
Open collector signal. Low when the PSU over temperature protection occurs. The maximum sink current is 10mA and the maximum external voltage is 20V.
16 FAN-FAIL1-GND Alarm signal of fan fail.
Normally open contact. “Short” when the internal fan fails. Relay contact rating(maximum) is 30V/1A resistive.

Control Pin No. Assignment (CN25) : HRS DF11-08DP-2DS or equivalent 1 7

MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-22

Mating Housing HRS DF11-08DS or equivalent
Terminal HRS DF11-**SC or equivalent

 

Pin No. Function Description
 

1,3

  

12V-AUX

 Auxiliary voltage output, 11.4~12.6V, referenced to pin 2,4(GND-AUX). Only for remote on-off control & Alarm signal. The maximum load current is 0.1A. This output is not controlled by the “Remote ON/OFF” function.
 

2,4

  

GND-AUX

 Auxiliary voltage output GND.

The signal return is isolated from the output terminals (+V & -V).
 

5,7

  

RC+

  

 

The output can be turned ON-OFF in association with RC+ and RC-.
 

6,8

  

RC-

MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-23 MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-24 MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-25 MEAN-WELL-RST-15K-HV-15KW-Input-With-High-Voltage-Output-26

Documents / Resources

MEAN WELL RST-15K-HV 15KW Input With High Voltage Output [pdf] Instruction Manual
RST-15K-HV, 15KW Input With High Voltage Output, High Voltage Output, 15KW Input Output, Output

References

Related Posts

Leave a comment

Your email address will not be published. Required fields are marked *