MEAN WELL HBG-1oo Series 100W Constant Current Mode LED Driver User Guide

HBG-100 series is a 100W AC/DC LED driver featuring a circular shape design. It operates from 90~305VAC and offers constant current output models with different rated voltages between 24V and 60V. Thanks to the high efficiency of up to 91.5%, with the fanless design, the entire series is able to operate for -40°C ~ +85°C case temperature under free air convection. The design of metal housing and IP67/IP65 ingress protection level allows this series to fit both indoor and outdoor applications. HBG-100 is equipped with various function options, such as dimming methodologies, so as to provide optimal design flexibility for LED lighting systems.

Model Encoding

SPECIFICATION

MODEL		HBG-100-24		HBG-100-36		HBG-100-48	HBG-100-60
OUTPUT	RATED CURRENT	4A		2.7A		2A	1.6A
	RATED POWER	96W		97.2W		96W	96W
	CONSTANT CURRENT REGION Note.2	14.4 ~ 24V		21.6 ~ 36V		28.8 ~ 48V	36 ~ 60V
	OPEN CIRCUIT VOLTAGE(max.)	25V		37V		49V	62V
	CURRENT ADJ. RANGE	Adjustable for A/AB-Type (via built-in potentiometer)
		2.4 ~ 4A		1.62 ~ 2.7A		1.2 ~ 2A	1.0 ~ 1.6A
	CURRENT RIPPLE	5.0% max. @rated current
	CURRENT TOLERANCE	±5.0%
	SETUP TIME Note.4	2000ms / 115VAC 500ms / 230VAC
INPUT	VOLTAGE RANGE Note.3	90 ~ 305VAC 127 ~ 431VDC (Please refer to the “STATIC CHARACTERISTIC” section)
	FREQUENCY RANGE	47 ~ 63Hz
	POWER FACTOR	PF>0.96/115VAC, PF>0.96/230VAC, PF>0.94/277VAC@full load (Please refer to the “POWER FACTOR (PF) CHARACTERISTIC” section)
	TOTAL HARMONIC DISTORTION	THD< 20%(@load≧60%/115VC,230VAC; @load≧75%/277VAC) (Please refer to the “TOTAL HARMONIC DISTORTION(THD)” section)
	EFFICIENCY (Typ.) Note.5	90.5%		91%		91%	91.5%
	AC CURRENT (Typ.)	1.1A / 115VAC	0.5A / 230VAC		0.45A / 277VAC
	INRUSH CURRENT (Typ.)	COLD START 60A(twidth=550μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
	MAX. No. of PSUs on 16A CIRCUIT BREAKER	4 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 230VAC
	LEAKAGE CURRENT	<0.75mA / 277VAC
PROTECTION	OVER CURRENT	95 ~ 108%
		Constant current limiting
	OVERVOLTAGE	28 ~ 35V		41 ~ 49V		54 ~ 63V	65 ~ 75V
		Shut down o/p voltage re-power on to recovery
	OVER TEMPERATURE	Shut down o/p voltage re-power on to recovery
ENVIRONMENT	WORKING TEMP.	Tcase=-40 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
	MAX. CASE TEMP.	Tcase=+85℃
	WORKING HUMIDITY	20 ~ 95% RH non-condensing
	STORAGE TEMP., HUMIDITY	-40 ~ +80℃, 10 ~ 95% RH
	TEMP. COEFFICIENT	±0.03%/℃ (0 ~ 50℃)
	VIBRATION	10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, and Z axes
SAFETY & EMC	SAFETY STANDARDS	UL8750(type”HL”),CSA C22.2 No.250.13-12, ENEC BS EN/EN61347-1,BS EN/EN61347-2-13 independent, BS EN/EN62384; GB19510.1,GB19510.14, BIS IS15885(for 36A,48A,60A only), EAC TP TC 004,IP65 or IP67 approved
	DALI STANDARDS	Compliance to IEC62386-101, 102, 207 for DA-Type only
	WITHSTAND VOLTAGE	I/P-O/P:3.75KVAC	I/P-FG:2KVAC		O/P-FG:0.5KVAC
	ISOLATION RESISTANCE	I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
	EMC EMISSION	Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load≧60%) ; BS EN/EN61000-3-3, GB/T 17743 ,GB17625.1, EAC TP TC 020
	EMC IMMUNITY	Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547,light industry level (surge immunity:Line-Earth:4KV, Line-Line:2KV), EAC TP TC 020
OTHERS	MTBF	2433.4K hrs min. Telcordia SR-332 (Bellcore) ;299.3K hrs min. MIL-HDBK-217F (25℃)
	DIMENSION	ψ130mm 66.5mm (D H)
	PACKING	1.18Kg; 12pcs/15.7Kg/1.43CUFT(Blank/A/B Type),1.89CUFT(E Type)
NOTE	1. All parameters NOT specially mentioned are measured at 230VAC input, rated current, and 25℃ of ambient temperature. 2. Please refer to “DRIVING METHODS OF LED MODULE”. 3. De-rating may be needed under low input voltages. Please refer to the “STATIC CHARACTERISTIC” sections for details. 4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to an increase of the set-up time. 5. The DA-type power supply is less efficient than the typical efficiency in specification by 1%. 6. The driver is considered a component that will be operated in combination with the final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify the EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 7. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75℃ or less. 8. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com 9. The ambient temperature derating of 3.5℃/1000m with fanless models and 5℃/1000m with fan models for operating altitudes higher than 2000m(6500ft). 10. For any application note and IP waterproof function installation caution, please refer to our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf ※ Product Liability Disclaimer： For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

Blank TYPE

: Max. Case Temperature. (case temperature measured point)

Ta: Ambient Temperature measured point

A-Type

: Max. Case Temperature. (case temperature measured point)

Ta: Ambient Temperature measured point

B/DA-Type

: Max. Case Temperature. (case temperature measured point)
Ta: Ambient Temperature measured point

AB-Type

: Max. Case Temperature. (case temperature measured point)
Ta: Ambient Temperature measured point

BLOCK DIAGRAM

DRIVING METHODS OF LED MODULE

This series works in constant current mode to directly drive the LEDs.

DIMMING OPERATION

3 in 1 dimming function (for B/AB-Type)

Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
Dimming source current from power supply: 100uA (typ.)

Applying additive 1 ~ 10VDC

Apolvina additive 10V PWM sianal (frequency rande 100Hz ~ 3KHz):

Applying additive resistance:

Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follows, or please contact MEAN WELL for other options.

Using a switch and relay can turn ON/OFF the lighting fixture.

DALI Interface (primary side; for DA-Type)

Apply the DALI signal between DA+ and DA-.
DALI protocol comprises 16 groups and 64 addresses.
The first step is fixed at 8% of output.

OUTPUT LOAD vs TEMPERATURE(Note.8)STATIC CHARACTERISTIC

De-rating is needed under low input voltage

POWER FACTOR (PF) CHARACTERISTIC

Tcase at 75°C

TOTAL HARMONIC DISTORTION (THD)

48V Model, Tcase at 75°C

EFFICIENCY vs LOAD

HBG-100 series possess superior working efficiency that up to 91% can be reached in field applications.

48V Model, Tcase at 75°C

LIFETIME

INSTALLATIONS

Caution

Please inspect the appearance of the driver if the package is damaged. There should not be any cracks.
Please do not drop or bump the driver.
All screws including the suspension screw should be paired with a spring washer and locked tight.

The entire luminaire, including the driver, should be limited to 10 kg or less.
The luminaire should be cautiously protected from damage due to shock throughout packaging and transportation.
Please thoroughly follow the preceding cautionary notes to prevent the luminaire from falling, leading to injuries

Downloaded from Arrow.com.

User’s Manual

Documents / Resources

MEAN WELL HBG-1oo Series 100W Constant Current Mode LED Driver [pdf] User Guide
HBG-1oo Series 100W Constant Current Mode LED Driver, HBG-1oo Series, 100W Constant Current Mode LED Driver, Constant Current Mode LED Driver, Current Mode LED Driver, Mode LED Driver, LED Driver, Driver

References

User Manual

MEAN WELL HBG-1oo Series 100W Constant Current Mode LED Driver

FAQs

Features

Applications

Description