GC30B 16.8 – 30W Power Adaptor with Charging Function
User Manual

Features

• Charger for lead-acid batteries (flooded, Gel and AGM) and li-ion batteries (lithium iron and lithium manganese)(Note.1)
• Universal AC input / Full range
• 2 pole AC Inlet IEC320-C8
• Class II power (without earth pin)
• No load power consumption <1.0W
• Constant current and voltage(CC,CV mode)
• Suitable for continued load
• For high surge current equipment
• Protections: Short circuit / Overload / Over voltage / Over temp.
• 2 colors of LED indicate for charging status
• Fully enclosed plastic case
• High reliability
• Approvals: UL / CUL / TUV / EAC / CB / FCC / CE / UKCA
• 2 years warranty

https://www.youtube.com/watch?v=ouJ1SBaOALM&list=PLvUyt_OJELVrHoIIRgvHF2NQ-j39-NH-J&index=4
https://www.meanwell.com/Upload/PDF/Adaptor_EN.pdf

GTIN CODE
MW Search: https://www.meanwell.com/serviceGTIN.aspx.

ORDER NO.		GC30B-OP1J	GC30B-1 P1 J	GC30B-11P1J	GC30B-2P1J	GC30B-4P1J	GC30B-5P1J	GC30B-6P1J
OUTPUT	SAFETY MODEL NO.	GC30B-0	GC30B-1	GC30B-11	GC308-2	GC3013-4	GC30B-5	GC30B-6
	DC VOLTAGE SET AT Note.3	4.2V	5.6V	7.2V	8.4V	14.3V	16.8V	28.6V
	RATED CURRENT	4A	3.99A	3A	3A	2.09A	1.6A	1.04A
	CURRENT RANGE	0 – 4A	0 – 3.99A	0 – 3A	0 -3A	0 – 2.09A	0 – 1.6A	0 – 1.04A
	RATED POWER	16.8W	22.38W	21.6W	25.2W	30W	27W	30W
	RIPPLE & NOISE (max.) Note.4	50mVp-p	50mVp-p	80mVp-p	80mVp-p	100mVp-p	100mVp-p	150mVp-p
	CHARGING VOLTAGE RANGE Note.5	3.6 – 4.4V	5 – 5.8V	6.5 – 7.5V	7.7 – 8.6V	13.5 -14.5V	16 -17V	27.1 – 28.8V
	LINE REGULATION Note.6	±1.0%	±0.5%	±0.5%	±0.5%	±0.5%	±0.5%	±0.5%
	LED INDICATOR	Green LED ON < 100mA, Red LED ON > 250mA
	SETUP, RISE, HOLD UP TIME	200ms, 50ms, 16ms at full load
INPUT	VOLTAGE RANGE	90 – 264VAC 127 – 370VDC
	FREQUENCY RANGE	47 – 63Hz
	EFFICIENCY (Typ.)	55% 170%		I74%	176%	78%	178%	80%
	AC CURRENT	0.7A /100VAC; 0.35A/230VAC
	INRUSH CURRENT (max.)	40A/230VAC
	LEAKAGE CURRENT(max.)	0.25mA/240VAC
PROTECTION	OVERLOAD	90 -110% Constant current mode and over 300% pulsing mode
		Protection type: Constant current limiting, recovers automatically after fault condition is removed
	OVERVOLTAGE	110 -135% rated output voltage
		Protection type: Clamp by zener diode
	OVER TEMPERATURE	IC1_Tj > 130t
		Protection type: Shut down o/p voltage, recovers automatically after temperature goes down
ENVIRONMENT	WORKING TEMP.	0 – +50t (Refer to output load derating curve)
	WORKING HUMIDITY	20% – 90% RH non-condensing
	STORAGE TEMP., HUMIDITY	-20 – +85t , 10 – 95% RH
	TEMP. COEFFICIENT	±0.03% / t. (0 – 50t)
	VIBRATION	10 – 500Hz, 2G 10min./1 cycle, the period for 60min. each along X, Y, and Z axes
SAFETY & EMC	SAFETY STANDARDS	UL62368.1, CSA22.2, BS EN/EN62368.1, EAC TP TC 004 approved
	WITHSTAND VOLTAGE	I/P-0/P:3KVAC
	ISOLATION RESISTANCE	I/P-0/P:100M Ohms! 500VDC / 25t/ 70% RH
	EMC EMISSION	Compliance to BS EN/EN55014-1 class B, FCC part 15 Class B, EAC TP TC 020
	EMC IMMUNITY	Compliance to BS EN/EN61000-4-2,3,4,5,6,11, light industry level, criteria A, EAC TP TC 020
OTHERS	DIMENSION	108*67*36mm (L’APH)
	PACKING	309g; 54pcs / 19kg / CARTON
CONNECTOR	PLUG	Standard type P1J: 2.10 ‘ 5.5(1) ‘ 11mm, tuning fork type center positive for stock; another type available by customer requested
	CABLE	Standard type 18Awg UL1185 6ft and 4ft for 4.2V-8.4V output only for stock; another type available by customer requested
NOTE	1. Moclification for charger specification may be required for different battery specification. Please contact the battery vendor and MEAN WELL for details. 2. AII parameters are specified at 230VAC input, rated load, 25t 70% RH ambient. 3. DC voltage: The output voltage set at point measure by plug terminal & 0% load. 4. Ripple & noise are measured at 20MHz by using a 12″ twisted pair terminated with a 0.1uf & 47uf capacitor. 5. Output charging voltage range is measured from 0% to 100% rated load. 6. Line regulation is measured from low line to high line at rated load. Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.conterviceDisclaimeraspx

Mechanical Specification

Charging Curve

Suitable for lead-acid batteries (flooded,Gel and AGM) and Li-ion batteries (lithium iron and lithium manganese)

LED Display

LED Status	Load Condition
Red	Charging
Green	Float Charging

Plug Assignment
Standard plug: P1J (option)

P1J
P/N	CENTER
OUTPUT	+

Derating Curve

Static Characteristics

Documents / Resources

MEAN WELL GC30B 16.8 - 30W Power Adaptor with Charging Function [pdf] User Manual GC30B, 16.8 30W Power Adaptor with Charging Function, 16.8 30W Power Adaptor, Power Adaptor, GC30B, Adaptor

References

• User Manual