MEAN WELL XLC-25-KN Series 25W Multiple Stage Constant Power LED Driver
Product Specifications
- Model: XLC-25-H-KN
- Output:
- Open Circuit Voltage: 60V
- Default Current: 300mA
- Current Adjustment Range: 0.3-1.05A
- Constant Current Region: 9-54V
- Rated Power: 25W
- Current Ripple
- Current Tolerance
- Dimming Range Setup, Rise Time: Note.5
Product Usage Instructions
Installation
Follow these steps to install the XLC-25-H-KN LED Driver:
- Ensure the DC input voltage is within the range of 176-280VDC.
- Connect the LED driver to the appropriate LED lighting system.
- Secure all connections and ensure proper grounding.
Operation
To operate the LED driver:
- Apply power within the specified input voltage range.
- Adjust the current within the recommended range for desired brightness.
- Monitor current ripple and ensure it is within acceptable limits.
XLC-25-KN-S Series
- (Built-in type)
XLC-25-KN Series
- (Independent type)
Dimming Functionality
If dimming functionality is required:
- Refer to Note.5 for dimming range setup and rise time information.
- Follow the dimming instructions provided in the user manual.
Features
- Constant power mode output with multiple stage selectable by the ETS database
- Plastic housing with Class Il and PFC design
- Flicker free, complying with CE ErP directive
- Standby power consumption <0.5W
- Meet emergency lighting (EL) application
- KNX/EIB protocol, support KNX data security
- Minimum dimming level 0.5%
- Function: operation hours, power consumption feedback, log/linear curve selection, etc
- 5 years warranty
Applications
- Recessed Light
- Down Light
- Panel Light
- Commercial Lighting
- Decorative Lighting
- KNX digital Lighting
GTIN CODE
- MW Search: https://www.meanmell.com/seviceGTIN.asox
Description
- XLC-25-KN Series is a 25W with constant power output LED driver. It can operate from 100-305VAC and output current ranging between 300 mA to 1050 mA, selectable bythe ETS database. The integrated KNX interface avoids using the complicated KNX-DALI gateway. Thanks to high efficiency up to 88%, it can operate for- 25 °C ~85°C case temperature under free air convection. XLC-25-KN is designed based on the latest safety regulations, and provides more flexibility for LED Lighting application.
Model Encoding
SPECIFICATION
| MODEL | XLC-25-H-KN | |||
| OUTPUT | OPEN CIRCUIT VOLTAGE Note.2 | 60V | ||
| DEFAULT CURRENT | 300mA | |||
| CURRENT ADJ.RANGE
(BY ETS Database) |
0.3~1.05A | |||
| CONSTANT CURRENT REGION Note.3 | 9~54V | |||
| RATED POWER Note.4 | 25W | |||
| CURRENT RIPPLE | <4%(@full load) | |||
| CURRENT TOLERANCE | ±5% | |||
| DIMMING RANGE | 0~100% | |||
| SETUP, RISE TIME Note.5 | 500ms, 100ms/230VAC, 1000ms, 100ms/115VAC | |||
| INPUT | VOLTAGE RANGE | 100~ 305VAC 141 ~ 400VDC | ||
| FREQUENCY RANGE | 47 ~ 63Hz | |||
| POWER FACTOR | PF≧0.97/115VAC, PF≧0.95/230VAC, PF≧0.92/277VAC@full load
(Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section) |
|||
| TOTAL HARMONIC DISTORTION | THD<10%(@load≧50%/230VAC; @load≧75%/277VAC), THD<15%(@load≧50%/115VAC)
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section) |
|||
| EFFICIENCY (Typ.) Note.6 | 88% | |||
| AC CURRENT | 0.35A / 115VAC 0.18A / 230VAC 0.15A/277VAC | |||
| INRUSH CURRENT(Typ.) | COLD START 10A(twidth=100μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 | |||
| MAX. No. of PSUs on 16A CIRCUIT BREAKER | 71 units (circuit breaker of type B) / 71 units (circuit breaker of type C) at 230VAC | |||
| LEAKAGE CURRENT | <0.75mA / 277VAC | |||
| STANDBY POWER CONSUMPTION Note.7 | Standby power consumption<0.5W(Dimming off) | |||
| PROTECTION | SHORT CIRCUIT | Hiccup mode, recovers automatically after fault condition is removed | ||
| OVER TEMPERATURE | Stage 1: De-rating to 75% loading; Stage 2: De-rating to 50% loading. Recovers automatically after fault condition is removed. | |||
| ENVIRONMENT | WORKING TEMP. | Tcase=-25 ~ 85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section) | ||
| MAX. CASE TEMP. | Tcase=85℃ | |||
| WORKING HUMIDITY | 20 ~ 90% RH non-condensing | |||
| STORAGE TEMP., HUMIDITY | -40 ~ +80℃, 10 ~ 95% RH | |||
| TEMP. COEFFICIENT | ±0.03%/℃ (0 ~ 50℃) | |||
| VIBRATION | 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes | |||
| SAFETY & EMC |
SAFETY STANDARDS |
ENEC BS EN/EN61347-1, BS EN/EN61347-2-13(EL) appendix J suitable for emergency installations(DC input 176-280VDC), BS EN/EN62384; GB/T19510.1, GB/T19510.213, EAC TP TC 004 approved;
Design refers to AS/NZS 61347-1, AS/NZS 61347-2-13 |
||
| WITHSTAND VOLTAGE | I/P-O/P:3.75KVAC | |||
| ISOLATION RESISTANCE | I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH | |||
| EMC EMISSION | Parameter | Standard | Test Level/Note | |
| Conducted | BS EN/EN55015(CISPR15) ,GB/T 17743 | —– | ||
| Radiated | BS EN/EN55015(CISPR15) ,GB/T 17743 | —– | ||
| Harmonic Current | BS EN/EN61000-3-2 , GB17625.1 | Class C @load≥50% | ||
| Voltage Flicker | BS EN/EN61000-3-3 | —– | ||
| BS EN/EN61547 | ||||
| EMC IMMUNITY | Parameter | Standard | Test Level/Note | |
| ESD | BS EN/EN61000-4-2 | Level 3, 8KV air ; Level 2, 4KV contact | ||
| Radiated | BS EN/EN61000-4-3 | Level 2 | ||
| EFT/Burst | BS EN/EN61000-4-4 | Level 2 | ||
| Surge | BS EN/EN61000-4-5 | Level3, 1KV/Line-Line | ||
| Conducted | BS EN/EN61000-4-6 | Level 2 | ||
| Magnetic Field | BS EN/EN61000-4-8 | Level 2 | ||
| Voltage Dips and Interruptions | BS EN/EN61000-4-11 | 70% residual voltage for 10
period, 0% residual voltage for 0.5 periods |
||
| OTHERS | KNX | Certified protocol | ||
| FLICKER Note.8 | PstLM ≤ 1, SVM ≤ 0.4 | |||
| MTBF | 3949.8 K hrs min. Telcordia SR-332 (Bellcore) ; 338.5 Khrs min. MIL-HDBK-217F (25℃) | |||
| DIMENSION | 147*40*32mm,107*40*32mm (L*W*H) | |||
| PACKING | 141.6g; 60pcs/9.5Kg/0.58CUFT(for blank type); 160g; 50pcs/9Kg/0.57CUFT(for S-type) | |||
| NOTE | 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Output hiccups under no-load condition. 3. Please refer to “DRIVER METHODS OF LED MODULE”. 4. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details. 5. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to an increase of the set up time. 6. Efficiency is measured at 500mA/50V output set by ETS database. 7. Standby power consumption is measured at 230VAC. 8. Flicker is measured at full load with LED modules. 9. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify the EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 10. For XLC(except -S) series: RCM is on a voluntary basis and meets relevant IEC or AS/NZS standards complying with AS/NZS 4417.1. 11. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 70℃ or less. 12. The ambient temperature de-rating of 3.5℃/1000m with fanless models and 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft). 13. For more information, please contact MEAN WELL sales. Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx |
|||
BLOCK DIAGRAM
DRIVING METHODS OF LED MODULE
- I-V Operating Area
- XLC-25-H-KN
CONSTANT POWER TABLE
XLC-25-KN is a multiple-stage constant power driver, selection of output current through the Database.
| Vo | Io | Vo | Io |
| 9~54V | 300mA(Default) | 9~36V | 700mA |
| 9~54V | 350mA | 9~33V | 750mA |
| 9~54V | 400mA | 9~31V | 800mA |
| 9~50V | 450mA | 9~29V | 850mA |
| 9~50V | 500mA | 9~28V | 900mA |
| 9~45V | 550mA | 9~26V | 950mA |
| 9~42V | 600mA | 9~25V | 1000mA |
| 9~38V | 650mA | 9~24V | 1050mA |
DIMMING OPERATION
- KNX interface
- Apply KNX Bus cable between KNX+ and KNX-
- The application program(database) can be downloaded via Online Catalogs from ETS or via http://www.meanwell.com/productCatalog.aspx
| Parametrization options | Description |
| Device Setting | Select current level
Select model Behavior bus power up |
| Parameter Setting | Basic Setting
normal Dimmer, staircase light switch function relative dimming function absolution dimming function Feedback Setting dimming value report on/off state report lamp failure report Lock function |
| Scenes | Learn scene
scene1~scene32 |
| Automatic function | Automatic function1~4 |
| operating hours | Counting of operating hours
Constant light output(CLO) Lifetime pre-warning |
| Power consumption | Voltage, current, power feedback
Energy consumption feedback |
| Temperature Measurement | customize the alarm temperature
Send temperature report cyclically |
| Auto-dimming over time | Optional gradient dimming |
| Correction characteristic | Correction by the lux measured value(lux) |
| Push Dim Port | Push dim
AC monitor |
- CONSTANT LIGHT OUTPUT
PUSH dimming or AC/DC input monitor(Primary side)
PUSH dimming
- KNX bus need to be connected when using PUSH Dimming
- The detailed function of PUSH dimming, please refer to the database.
- The maximum length of the cable between the push button and driver is 20 meters.
- The mechanical push button can be connected only between the PUSH terminal, as displayed in the diagram, and AC/L (in brown or black); It will not function properly if it is connected to AC/N.
- In case the PUSH dimming is set locally, up to 10 drivers can perform the PUSH dimming at the same time when utilizing one common push button.
- In case the PUSH dimming is set independently via ETS, the number of drivers is done through group address and determined by the ETS project designer.
AC/DC input monitor
- KNX bus need to be connected when using AC/DC input monitor
- The detailed function of AC/DC input monitor(emergency lighting), please refer to the database and instruction manual.
OUTPUT LOAD vs TEMPERATURE
STATIC CHARACTERISTIC
LIFE TIME
TOTAL HARMONIC DISTORTION (THD)
POWER FACTOR (PF) CHARACTERISTIC
EFFICIENCY vs LOAD
- XLC-25-KN series possess superior working efficiency that is up to 88% in field applications.
- XLC-25-H-KN, Tcase at 75°C
MECHANICAL SPECIFICATION
Installation Manual
Please refer to : http://www.meanwell.com/manual.html
FAQ
Q: What is the default current output of the XLC-25-H-KN LED Driver?
A: The default current output is 300mA.
Q: What is the open circuit voltage of the LED driver?
A: The open circuit voltage is 60V.
Q: How do I adjust the current output of the LED driver?
A: The current output can be adjusted within the range of 0.3-1.05A.
Documents / Resources
 |
MEAN WELL XLC-25-KN Series 25W Multiple Stage Constant Power LED Driver [pdf] Owner's Manual XLC-25-H-KN, XLC-25-KN Series 25W Multiple Stage Constant Power LED Driver, 25W Multiple Stage Constant Power LED Driver, Stage Constant Power LED Driver, Power LED Driver, LED Driver |
 |
MEAN WELL XLC-25-KN Series 25W Multiple Stage Constant Power LED Driver [pdf] Owner's Manual XLC-25-KN Series, XLC-25-KN Series 25W Multiple Stage Constant Power LED Driver, 25W Multiple Stage Constant Power LED Driver, Multiple Stage Constant Power LED Driver, Stage Constant Power LED Driver, Power LED Driver, LED Driver |