Owner's Manual for MEAN WELL models including: XLC-25-KN Series, XLC-25-KN Series 25W Multiple Stage Constant Power LED Driver, 25W Multiple Stage Constant Power LED Driver, Multiple Stage Constant Power LED Driver, Stage Constant Power LED Driver, Power LED Driver, LED Driver
25W Multiple-Stage Constant Power LED Driver XLC-25-KN series ‧ I ‧
File Info : application/pdf, 8 Pages, 1.05MB
DocumentDocument25W Multiple-Stage Constant Power LED Driver
XLC-25-KN series
User's Manual
(for XLC-25-H-KNS)
DC Input: 176-280VDC
I
Note.10
File Name:XLC-25-KN-SPEC 2025-01-24
25W Multiple-Stage Constant Power LED Driver
XLC-25-KN series
SPECIFICATION
MODEL
XLC-25-H-KN
OUTPUT
OPEN CIRCUIT VOLTAGE Note.2
DEFAULT CURRENT CURRENT ADJ.RANGE (BY ETS Database)
CONSTANT CURRENT REGION Note.3 RATED POWER Note.4
CURRENT RIPPLE
CURRENT TOLERANCE DIMMING RANGE SETUP, RISE TIME Note.5
60V
300mA 0.3~1.05A
9~54V 25W <4%(@full load) ±5% 0~100% 500ms, 100ms/230VAC, 1000ms, 100ms/115VAC
INPUT
VOLTAGE RANGE
100~ 305VAC 141 ~ 400VDC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR
PF0.97/115VAC, PF0.95/230VAC, PF0.92/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
TOTAL HARMONIC DISTORTION
THD<10%(@load50%/230VAC; @load75%/277VAC), THD<15%(@load50%/115VAC) (Please refer to "TOTAL HARMONIC DISTORTION(THD)" section)
EFFICIENCY (Typ.) Note.6 88%
AC CURRENT
0.35A / 115VAC 0.18A / 230VAC 0.15A/277VAC
INRUSH CURRENT(Typ.) COLD START 10A(twidth=100s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER LEAKAGE CURRENT
71 units (circuit breaker of type B) / 71 units (circuit breaker of type C) at 230VAC <0.75mA / 277VAC
STANDBY POWER CONSUMPTION Note.7
PROTECTION SHORT CIRCUIT OVER TEMPERATURE WORKING TEMP.
MAX. CASE TEMP.
Standby power consumption<0.5W(Dimming off)
Hiccup mode, recovers automatically after fault condition is removed Stage 1: De-rating to 75% loading; Stage 2: De-rating to 50% loading. Recovers automatically after fault condition is removed. Tcase=-25 ~ 85 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section) Tcase=85
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/ (0 ~ 50)
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS
ENEC BS EN/EN61347-1, BS EN/EN61347-2-13(EL) appendix J suitable for emergency installations(DC input 176-280VDC), BS EN/EN62384; GB/T19510.1, GB/T19510.213, EAC TP TC 004 approved; Design refer to AS/NZS 61347-1, AS/NZS 61347-2-13
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC
ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25/ 70% RH
SAFETY &
Parameter
Standard
Test Level/Note
EMC EMC EMISSION
Conducted Radiated
BS EN/EN55015(CISPR15) ,GB/T 17743 ----BS EN/EN55015(CISPR15) ,GB/T 17743 -----
Harmonic Current
BS EN/EN61000-3-2 , GB17625.1
Class C @load50%
Voltage Flicker
BS EN/EN61000-3-3
-----
BS EN/EN61547
Parameter
Standard
Test Level/Note
ESD
BS EN/EN61000-4-2
Level 3, 8KV air ; Level 2, 4KV contact
EMC IMMUNITY
Radiated EFT/Burst
BS EN/EN61000-4-3 BS EN/EN61000-4-4
Level 2 Level 2
Surge
BS EN/EN61000-4-5
Level3, 1KV/Line-Line
Conducted
BS EN/EN61000-4-6
Level 2
Magnetic Field
BS EN/EN61000-4-8
Level 2
Voltage Dips and Interruptions
BS EN/EN61000-4-11
70% residual voltage for 10 period, 0% residual voltage for 0.5 periods
OTHERS NOTE
KNX FLICKER Note.8
Certified protocol PstLM 1, SVM 0.4
MTBF
3949.8 K hrs min. Telcordia SR-332 (Bellcore) ; 338.5 Khrs min. MIL-HDBK-217F (25)
DIMENSION PACKING
147*40*32mm,107*40*32mm (L*W*H) 141.6g; 60pcs/9.5Kg/0.58CUFT(for blank type); 160g; 50pcs/9Kg/0.57CUFT(for S-type)
1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature. 2. Output hiccups under no-load condition. 3. Please refer to "DRIVER METHODS OF LED MODULE". 4. De-rating may be need under low input voltages. Please refer to "STATIC CHARACTERISTIC" sections for details. 5. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time. 6. Efficiency is measured at 500mA/50V output set by ETS database. 7. Standby power consumption is measured at 230VAC. 8. Flicker is measured at full load with LED modules. 9. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete
installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 10. For XLC(except -S) series: RCM is on a voluntary basis and meets relevant IEC or AS/NZS standards complying with AS/NZS 4417.1.
11.This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 70 or less. 12.The ambient temperature de-rating of 3.5/1000m with fanless models and 5/1000m with fan models for operating altitude higher than 2000m(6500ft). 13. For more information, please contact with MEAN WELL sales. Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
File Name:XLC-25-KN-SPEC 2025-01-24
25W Multiple-Stage Constant Power LED Driver
XLC-25-KN series
BLOCK DIAGRAM
EMI FILTER
I/P
&
RECTIFIERS
POWER SWITCHING
RECTIFIERS &
FILTER
DC to DC
Fosc : 90KHz
+V -V
O.L.P.
PWM&PFC CONTROL
O.T.P.
DRIVING METHODS OF LED MODULE
XLC-25-H-KN
For 25W application
60V
55V
300mA, 54V 460mA, 54V
50V
45V
40V
35V
30V
25V
20V
15V
10V
5V
300mA, 9V
0V
200mA
400mA
600mA
700mA, 36V
1050mA, 24V
800mA
1050mA, 9V
1000mA
1200mA
CURRENT & VOLTAGE LIMIT
DETECTION CIRCUIT
KNX INTERFACE
KNX+ KNX-
CONSTANT POWER TABLE
XLC-25-KN is a multiple-stage constant power driver, selection of output current through Database.
Vo Io 9~54V 300mA(Default) 9~54V 350mA 9~54V 400mA 9~50V 450mA 9~50V 500mA 9~45V 550mA 9~42V 600mA 9~38V 650mA
Vo Io 9~36V 700mA 9~33V 750mA 9~31V 800mA 9~29V 850mA 9~28V 900mA 9~26V 950mA 9~25V 1000mA 9~24V 1050mA
File Name:XLC-25-KN-SPEC 2025-01-24
25W Multiple-Stage Constant Power LED Driver
XLC-25-KN series
DIMMING OPERATION
KNX interface
Apply KNX Bus cable between KNX+ and KNXThe application program(database) can be downloaded via Online Catalogs from ETS or via http://www.meanwell.com/productCatalog.aspx
Parametrization options Description
Device Setting
Parameter Setting
Scenes Automatic function operating hours Power consumption Temperature Measurement Auto-dimming over time Correction characteristic Push Dim Port
·Select current level ·Select model ·Behavior bus power up
·Basic Setting ·normal Dimmer, staircase light ·switch function ·relative dimming function ·absolution dimming function
·Feedback Setting ·dimming value report ·on/off state report ·lamp failure report
·Lock function ·Learn scene ·scene1~scene32 ·Automatic function1~4 ·Counting of operating hours ·Constant light output(CLO) ·Life time pre-warning ·Voltage, current, power feedback ·Energy consumption feedback ·customize the alarm temperature ·Send temperature report cyclically
·Optional gradient dimming
·Correction by lux measured value(lux)
·Push dim ·AC monitor
CONSTANT LIGHT OUTPUT
100% Energy saving with CLO
80%
Power input relative to lumen output
60%
10000
20000
30000
40000
50000
Time/hrs
Power with CLO Lumen with CLO
Power without CLO Lumen without CLO
File Name:XLC-25-KN-SPEC 2025-01-24
25W Multiple-Stage Constant Power LED Driver
XLC-25-KN series
PUSH dimming or AC/DC input monitor(Primary side)
PUSH dimming
XLC-25-KN
AC/N (or Backup DC input) AC/L (or Backup DC input)
Push Button
AC/N AC/L PUSH
KNX bus need to be connected when using PUSH Dimming The detailed function of PUSH dimming, please refer to the database. The maximum length of the cable between the push button and driver is 20 meters. The mechanical push button can be connected only between the PUSH terminal, as displayed in the diagram,
and AC/L (in brown or black); It will not function properly if it is connected to AC/N. In case the PUSH dimming is set locally, up to 10 drivers can perform the PUSH dimming at the same time when utilizing one common push button. In case the PUSH dimming is set independently via ETS, the number of drivers is done through group address and determined by the ETS project designer.
AC/DC input monitor
XLC-25-KN
AC/N (or Backup DC input) AC/L (or Backup DC input)
AC/N AC/L PUSH
KNX bus need to be connected when using AC/DC input monitor The detailed function of AC/DC input monitor(emergency lighting), please refer to the database and instruction manual.
File Name:XLC-25-KN-SPEC 2025-01-24
LOAD (%)
25W Multiple-Stage Constant Power LED Driver
XLC-25-KN series
OUTPUT LOAD vs TEMPERATURE
100
80
230 VAC
60
110 VAC
40
20
-25 -15
0
15
30
40
50 60
70 (HORIZONTAL)
AMBIENT TEMPERATURE ,Ta ()
STATIC CHARACTERISTIC
LOAD (%)
100 90 80 70 60 50 40
100 110 130 150 170 190 210 230 250 270 290 305
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
LIFE TIME
LOAD (%)
100 80 60 40 20
-25
0
20
45
55
65
75
85 (HORIZONTAL)
Tcase ()
LIFETIME(Kh)
120 100
80 60 40 20
0 25 30 35 40 45 50 55 60 65 70 75 80 85
Tcase( )
File Name:XLC-25-KN-SPEC 2025-01-24
THD(%)
25W Multiple-Stage Constant Power LED Driver
XLC-25-KN series
TOTAL HARMONIC DISTORTION (THD)
XLC-25-H-KN,Tcase at 75
12
10
8
6
4
2
0 50 %
60 %
70 %
80 %
90 %
10 0%
LOAD (700mA)
POWER FACTOR (PF) CHARACTERISTIC
XLC-25-H-KN,Tcase at 75
1 1 5V A C 2 3 0V A C 2 7 7V A C
THD(%)
12
10
8
6
4
2
0 50%
60%
70%
80%
90%
100%
LOAD (1050mA)
115VAC 230VAC 277VAC
PF
1
0.98
0.96
0.94
0.92 0.9
0.88
TBD
0.86
115VAC 230VAC 277VAC
0.84
0.82
0.8 50%
60%
70%
80%
90%
100%
LOAD (700mA)
PF
1
0.98
0.96
0.94
0.92
0.9 0.88 0.86
TBD
0.84
0.82
0.8 50%
60%
70%
80%
90%
LOAD (1050mA)
EFFICIENCY vs LOAD
XLC-25-KN series possess superior working efficiency that up to 88% can be reached in field applications. XLC-25-H-KN,Tcase at 75
115VAC 230VAC 277VAC
100%
90
85
80
75
70 65
TBD
60
55 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD (700mA)
115VAC 230VAC 277VAC
EFFICIENCY (%)
90 85 80 75 70 65 60 55 50 45
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD (1050mA)
115VAC 230VAC 277VAC
EFFICIENCY (%)
File Name:XLC-25-KN-SPEC 2025-01-24
25W Multiple-Stage Constant Power LED Driver
XLC-25-KN series
MECHANICAL SPECIFICATION
XLC-25-KN Built-in Type
2-3.6
107 mm 99 mm
Case No.XLC-25 Unit:mm Tolerance:±1
14.6 mm
32 mm
1 2
TB1
3
Terminal Pin No. Assignment( TB1)
Pin No. Assignment
1
AC/N
2
AC/L
3
PUSH
40 mm
TB2
1 2
1
KNX programming button
& LED indicator 50.5 mm
TB3 1 2
Terminal Pin No. Assignment(TB2)
Pin No. Assignment
1
+V
2
-V
Terminal Pin No. Assignment(TB3)
Pin No. Assignment
1
KNX+
2
KNX-
8-9mm
8-9mm
32 mm
Item
Order No.
Strain-relief cap 1**3XLC-SET
Quantity(MOQ/1Bag) 50pcs (2pcs 1 set)
2-3.6
40 mm 31.5 mm
1 2
TB1
3
Terminal Pin No. Assignment( TB1)
Pin No. Assignment
1
AC/N
2
AC/L
3
PUSH
14.6 mm
32mm
147 mm 99mm
Case No.XLC-25-S Unit:mm Tolerance:±1
TB2
1 2
KNX programming button
& LED indicator
50.5 mm
TB3 1
2
Terminal Pin No. Assignment(TB2)
Pin No. Assignment
1
+V
2
-V
Terminal Pin No. Assignment(TB3)
Pin No. Assignment
1
KNX+
2
KNX-
32 mm
8-9mm
8-9mm
Installation Manual
Please refer to : http://www.meanwell.com/manual.html
File Name:XLC-25-KN-SPEC 2025-01-24
Installation Manual-MEAN WELL Switching Power Supply Manufacturer