MASTERBUILT MB20041223 Shut Down Slide Kit Installation Guide

MB20041223 Shut Down Slide Kit

“

Product Specifications:

• Product Name: Shut Down Slide Kit, GSGXT
• Model Numbers: MB20041223, MB20043024
• Manufacturer: Unknown

Product Usage Instructions:

1. Preparation for Shutdown:

1. Remove charcoal from hopper, cooking grates, warming rack,
   manifold pieces, ash tray, and other accessories.
2. Remove the front hopper shroud, hardware connecting leg brace
   to legs, and hopper ash door.

2. Disassembling the Controller:

1. Unscrew the shutdown slide handle.
2. Remove screws on the shutdown flap hopper shroud and remove the
   shroud.
3. Disconnect controller connections and remove thumb screws from
   the back of the controller.
4. Disconnect wire connections on the side of the controller and
   loosen screws on the insulation housing.
5. Remove screws from the rear of the controller and remove the
   back panel.

3. Removing Hopper:

1. Disconnect wire connections and feed the controller wire
   through hopper pass-through holes.
2. Remove screws at the bottom and top near the manifold inside
   the body to detach the hopper.
3. Have someone hold the hopper while removing hardware to
   disconnect it from the body. Lay the hopper down.

4. Final Steps:

1. Disconnect the spring from the top shutdown flap assembly using
   needle-nose pliers.
2. Remove hardware from bottom shutdown flap assemblies and remove
   the connector rod.
3. Remove top and bottom shutdown flap assemblies.
4. Replace top and bottom shutdown flap assemblies and associated
   hardware. Keep flaps closed.
5. Replace the shutdown handle and tighten screws on the top
   shutdown flap.

5. Reassembly:

For reinstallation, follow all steps in reverse order.

Frequently Asked Questions (FAQ):

Q: Is it necessary to disconnect all controller connections
during shutdown?

A: Yes, disconnecting all controller connections ensures proper
disassembly and prevents damage.

Q: What precautions should be taken when removing the
hopper?

A: Use caution when disconnecting the hopper from the body,
ensuring someone holds it in place to avoid accidents.

“`

Shut Down Slide Kit, GSGXT

MB20041223, MB20043024

CAUTION
· Always remove plug from outlet before servicing your grill. · Make sure your grill has fully cooled to avoid burns. · Some components may have sharp edges. Use caution to avoid injury.
Note: Your grill may vary from images shown

1

2

3

Remove: charcoal from hopper, cooking grates, warming rack, all 3 manifold pieces, ash tray, and any other accessories on the grill.
4

A) Remove the front hopper shroud. B) Remove the hardware that connects
the leg brace to the legs. C) Remove the hopper ash door.
5

Unscrew the shutdown slide handle. 6

Remove 3 screws on the shutdown flap hopper shroud. Remove the shroud.

CONTROLLER

Remove the controller connections.

Remove the 4 thumb screws from the back of the controller. Remove the controller

601866 240906-GH

7

8

9

Disconnect two black and white wire connections on the side of the controller.

Loosen 3 screws on the insulation housing to make room for the power plug.

Remove 6 screws from rear of controller and remove the back panel.

10

11

2 SCREWS

Disconnect 2 wire connections and feed the controller wire through the hopper pass through holes. Note, you will have to remove
a zip tie from the inside of the hopper.
12

Remove the bottom (2 screws) next to the manifold inside of the body. 13

2 SCREWS

USE CAUTION, this step will disconnect the hopper from the body. Have a second party hold the hopper in place as your remove the hardware. Remove the top (2 screws) next to
the manifold inside of the body. This will disconnect the hopper. Remove the hopper from the body.

Lay the hopper down.

14

15

Disconnect the spring from the top shutdown flap assembly.
Note: it is recommended to use a pair of needle nose pliars to accomplish this

Remove hardware from the bottom shutdown flap assemblies. Remove the connector rod.

16

17

Remove top and bottom shutdown flap assemblies (6 screws).

18

19

Replace top and bottom shutdown flap assemblies.
20

Replace hardware from the top and bottom shutdown flap assemblies.

Shutdown flaps and connector rod components should remain in the closed position.

Keep the shutdown flaps in the closed position. Replace the shutdown handle.
Tighten the (2 Screws) on the top shutdown flap.

For installation, follow all steps in reverse.

Documents / Resources

MASTERBUILT MB20041223 Shut Down Slide Kit [pdf] Installation Guide MB20041223, MB20043024, MB20041223 Shut Down Slide Kit, Shut Down Slide Kit, Down Slide Kit, Slide Kit

References

• User Manual