M2COMM logo

Ultra-thin · Full graphic
Autonomous system · Environmentally friendly
ELSA-E
Electronic Shelf Labeling System

M2COMM EF22-S2 Electronic Shelf Labeling System

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 1

EF22-S2 Electronic Shelf Labeling System

RELIABLE CELLULARLIKE TECHNOLOGY 
Unique tree network for optimal coverage without interference from existing Wi-Fi networks
EASY PLUG-AND-PLAY SYSTEM
Self-networking system enables easy infrastructure setup
EXCEPTIONAL READABILITY
High resolution e-paper display for 180° viewing
LONG BATTERY LIFE & FAST UPDATES
Unique wireless protocol tuned to optimize the power consumption and network efficiency
ANTI-JAMMIMG FROM Wi-Fi
13,500 graphic tags are fully updated per hour
INTELLIGENT SYSTEM
Acknowledges updates; battery level and signal strength notifications

Technical Specification

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 2

MODEL NAME: EF22-S2
INFRASTRUCTURE
SIZE (W x H x T) mm 70 x 37.4 x 9.6
WEIGHT, g 24
ANTENNA EMBEDDED
NETWORK
INTERFACE WIRELESS
FREQUENCY SUB-GHz ISM
OPERATION MODE SELF-NETWORKING (AUTOMATIC CONNECTION BUILT-UP AND RECOVERY)
ENCRYPTION AES 128-bit
TRANSMISSION RANGE 100 METERS (LINE OF SIGHT)
OPERATING CONDITIONS
OPERATING TEMP/HUMIDITY 0 ~ 40°C / 35 ~ 55% (non-condensed)
STORAGE TEMP/HUMIDITY 0 ~ 40°C / 35 ~ 80% (non-condensed)
POWER 1 x CR2450
APPLICATIONS Retail, Smart Display
Display
RESOLUTION 250 x 122
DPI 130 pixel

Device Setup:

Access Point Setting
The Access Point has a wired connection to the base station (computer) and communicates wirelessly with the Router(s) via the M2COMM proprietary protocol.
Please refer to below procedure to setup your Access Point.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 3Status Indicators and Assembly:
M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 4LED status functions:
Red –Power-on self-test error
Green –Power on indicator
Blue –Network connection, shall flash slowly during boot-up and stay on while connection is built up successfully.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 5Access Point – Network Port:
GREEN network activity indicator—turns on when a cable connects the port to another Gigabit Ethernet port
YELLOW activity indicator—Flashes to indicate network activity over that port
M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 6Plug one end of the supplied Cat 5E cable into the Access Point, the other end should be plugged into your computer.
M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 7 Connect the supplied AC power adaptor as shown.
Use only the adapter that came with your Access Point

Router Setting
The Router(s) operate wirelessly, via the M2COMM proprietary protocol, with the Access Point and aisle light.
Please refer to below procedure to setup the Router.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 8Status Indicators and Assembly:
M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 9

LED status functions:
Red –Power-on self-test error
Green –Power on indicator
Blue –Network connection, shall flash slowly during boot-up and stay on while connection is built up successfully.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 10Connect the included AC power adaptor as shown.
Use only the adapter that came with your Router

ELSA-E Demo System IP setting:
The ELSA-E demo system is designed to use either a static IP address for a single Access Point or a dynamic IP address when multiple Access Points are installed.
IP Address Configuration (Static IP): Ensure that your Access Point is connected to your computer.
The Access Point comes pre-configured with a default IP Address (192.168.2.1). It’s necessary to modify the IP Address of the Ethernet port on your computer that is cabled to the M2COMM Access Point so that they can communicate with one another.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 11

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 12

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 13

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 14

Check Use the following IP address and enter information shown above. Select OK to apply new settings

IP Address Configuration (Dynamic IP):
For installations that contain multiple Access Points an external TCP/IP Ethernet hub is required. And please contact
M2COMM for further details.

M2COMM ELSA-E Demo Installation:

Software Installation:
Put below two executable files into the same folder on your computer. And double-click the “ELSA1.0_2.x.x.xxxx.exe” file to begin the installation.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 15

You may be asked for permission to allow the program to make changes to your computer; you must agree to this to enable installation to start.
Follow the on-screen instructions to finish the installation process.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 16

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 17

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 18

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 19

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 20

The ELSA-E Demo system has now been installed and executed on your computer. The icon will be hidden inside the toolbar, and you should now be able to locate this icon on your computer screen, by right click.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 21

And you can also launch the ELSA software by double click the icon on desktop.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 22

Setting Up the ELSA-E 2.7’’ ESL

Ensure that the Access Point is connected to your computer that the Router(s) and 2.7’’ ESL are installed throughout your premises and are powered on.

Install the AP

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 23

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 24

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 25M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 26

Preparing the Network 

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 27

ELSA system will start to find the available wireless channel to use, and the whole process will take 1 hour.
Press “Show detail” for more information.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 28

Install Router
Power on the Router

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 29

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 30

Install Tags 

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 31

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 32

Power ON Tags

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 33

Finish 

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 34

Show the image on ELSA-E 2.2’’ ESL

Load the CSV file to import the inventory list first.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 35M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 36M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 37M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 38M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 39

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 40

How to Display FCC ID Label(After certification, display it on the “Pairing Page)

  1. Wake Up the Tag: Ensure the EPD is not blank or shows a “sleep mark” (red/black square in the top-left corner).
    If “sleep mark” please activate wake-up mode from ELSA WEB until ED removes the “sleep mark.”M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 41
  2. Switch Screens: Switch the EPD display to the “Pairing Page
    Select the ED from ELSA WEB, then click the “Show Barcode” button.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 42

The ED will be preset to display the “Pairing Page” upon shipment.

M2COMM EF22-S2 Electronic Shelf Labeling System - Fig 43

Battery Caution:

The elements of the instructional safeguard shall be as follows:
– element 1a: not available
– element 2: “Do not ingest battery, Chemical Burn Hazard” or equivalent wording
– element 3: the following or equivalent text
[The remote control supplied with] This product contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
– element 4: the following or equivalent text
Keep new and used batteries away from children
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

FCC Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in  a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and a human body.

M2COMMUNICATION Inc. 17 Floor, No. 32 Gaotie 2nd
Road, Zhubei City, Hsinchu County 302, Taiwan (R.O.C.)
Tel: +886 3 657 8939 Fax: +886 3 657 6909 http://www.m2comm.co
SALES AND SUPPORT: info@m2comm.co

Copyright © 2017 M2COMMUNICATION Inc. All rights reserved. This document is the property of M2COMMUNICATION Inc. It contains information which is confidential and proprietary to M2COMMUNICATION Inc. No part of this document may be copied, reproduced or disclosed to third parties without the prior written consent of M2COMMUNICATION Inc. (Document number: PB-ELSA-Q001)

Documents / Resources

M2COMM EF22-S2 Electronic Shelf Labeling System [pdf] Instruction Manual
EF22-S2, 2AFXU-EF22-S2, 2AFXUEF22S2, EF22-S2 Electronic Shelf Labeling System, EF22-S2, Electronic Shelf Labeling System, Shelf Labeling System

References

Leave a comment

Your email address will not be published. Required fields are marked *