SilverStone FLP01

Accessories Content

This section details various accessories and their mounting purposes:

• Rubber Grommet / 3.5" HDD Mounting Rubber: Used for securing 3.5" HDDs.
• Motherboard Standoff: Used to mount motherboards.
• Mounting for 3.5" HDD, Motherboard, PSU: Components for mounting 3.5" HDDs, motherboards, and PSUs.
• Mounting for 5.25" ODD: Components for mounting 5.25" Optical Disc Drives.
• Mounting for 2.5" SSD: Components for mounting 2.5" SSDs.
• Mounting for 3.5" HDD: Components for mounting 3.5" HDDs.
• Cable Ties: Used for managing cables.

Installation Guide

Follow these steps for installing components into the FLP01 chassis:

1. Step 1: Remove Top Panel

   Diagram shows an arrow indicating the top panel is to be removed.

2. Step 2: Remove ODD Bracket

   Loosen the four screws securing the ODD bracket and remove it. Diagram shows screws being loosened and the bracket removed.

3. Step 3: Remove Center Crossbar

   Remove the center crossbar. Diagram shows an arrow indicating the removal of the crossbar.

4. Step 4: Prepare for 5.25" Device Installation

   If installing a 5.25" device other than an optical disc drive, first remove the front panel, then detach the optical disc drive panel. Diagram illustrates these actions.

5. Step 5: Install PSU

   Install the Power Supply Unit (PSU). Diagram shows the PSU being placed into its bay.

6. Step 6: Install IO Shield

   Install the I/O shield. Diagram shows the I/O shield being fitted into the chassis opening.

7. Step 7: Install Motherboard

   Install the motherboard. Diagram shows the motherboard being mounted onto the standoffs.

8. Step 8: Install 2.5" Devices

   Install 2.5" devices (e.g., SSDs). Diagram shows these devices being fitted into their mounting locations.

9. Step 9: Install Graphics Card

   Install the graphics card. Diagram shows the graphics card being inserted into a PCIe slot.

10. Step 10: Install Storage Devices onto ODD Bracket

    Install storage devices onto the ODD bracket. Diagram shows drives being mounted on the bracket.

11. Step 11: Reinstall Cross Bar

    Reinstall the cross bar into the chassis. Diagram shows the crossbar being put back into place.

12. Step 12: Reinstall ODD Bracket

    Reinstall the ODD bracket into the chassis. Diagram shows the ODD bracket being secured.

13. Step 13: Reinstall Top Panel

    Reinstall the top panel to complete the installation. Diagram shows the top panel being put back on the chassis.

Component Restrictions

This section outlines limitations and compatibility details for various components:

• CPU Cooler Height: Limited to 138mm, or 127mm with the center crossbar attached. The cooler may protrude 8mm beyond the motherboard edge.
• ODD Bracket Dimensions: The distance between the ODD bracket edge and the motherboard rear edge is 170mm. The height limitation below the optical drive is 88mm. The distance from the optical drive's front end to the motherboard rear edge is 348mm (measuring the optical drive length first is recommended).
• PSU Depth Limits: With the 120mm fan and 2.5" SSD mount used, the maximum PSU depth is 160mm. Without these, it can accommodate a PSU up to 170mm deep.
• Graphics Card Dimensions: Length is limited to 309mm, and width is limited to 133mm.
• Dust Filters: Dust filters on the left and right sides of the chassis are easily removable.
• Expansion Slot: The FLP01 provides an additional expansion slot supporting single-slot interface cards like the ECD01.
• Drive Installation Order: For a 5.25" device on top of the ODD cage with a 3.5" drive underneath, there is no specific installation order. For smaller drives, refer to the table for recommended orders.

Warranty Terms & Conditions

SilverStone Technology provides a warranty covering manufacturing defects. Key terms include:

• Defects or damages from defective production are covered.
• Exclusions: misuse, natural disasters, unauthorized modifications, or tampering with warranty labels.
• Liability is limited to the product's current market value.
• SilverStone Technology is obligated to repair or replace defective products.
• Warranty is valid only for the original purchaser through authorized distributors and resellers.
• Proof of purchase (dated receipt or invoice) is required for warranty eligibility.
• For warranty service, contact your retailer, reseller, or an authorized SilverStone distributor. A Return Merchandise Authorization (RMA) number may be required.
• Contact information for various regions is provided for support.

Hazardous Substances

The following table indicates the presence of hazardous substances in components, as per SJ/T 11364 standards. 'O' indicates content is below the regulatory limit, and '-' indicates it exceeds the limit.

Note: 'O' indicates the content of the hazardous substance in all homogeneous materials of the component is below the limit specified in GB/T 26572. '-' indicates the content of the hazardous substance in at least one homogeneous material of the component exceeds the limit specified in GB/T 26572, and this restricted substance is excluded.

Product certification mark is present, indicating compliance.