AiM User Guide

1 Models and years

This manual explains how to connect Solo 2 DL, EVO4S and ECULog to the bike engine control unit (ECU).

Compatible models and years:

• Ducati – Panigale V2 (from 2020)
• Ducati – Panigale V4 (Euro5 models only, from 2021)

2 Kit content and part numbers

AiM developed a specific installation bracket for Solo 2/Solo 2 DL and specific connection cables to the ECU for Solo 2 DL, EVO4S and ECULog.

2.1 Bracket for Solo 2/Solo 2 DL

Part number of Solo 2/Solo 2 DL installation bracket for Ducati Panigale V2 and V4 (Euro5 models only) is: X46KSTSDP.

Installation kit contains:

• 1 bracket (1)
• 2 Allen screws with flat head M4x10mm (2)
• 1 washer (3)
• 1 rawl nut (4)
• 1 Allen screw with rounded head M8x45mm (5)

[Image description: A diagram showing the installation bracket and associated hardware: 1 bracket, 2 flat head Allen screws, 1 washer, 1 rawl nut, 1 rounded head Allen screw.]

2.2 AiM cable for SOLO 2 DL

Part number of Solo 2 DL connection cable for Ducati Panigale V2 and V4 (Euro5 models only) is: V02589130.

Cable constructive scheme:

[Image description: A diagram showing the cable connections. A 7-pin Binder 712 male connector (solder termination view) connects to a 6-pin JST male connector (contact insertion view). The connections are: White wire: CAN1+, Blue wire: CAN1-, Red wire: 9-15V Power Input, Orange wire: K Line, Black wire: GND. Pins 3, 4, 5 on the Binder connector are marked 'nc' (not connected). Pins 4, 5, 6 on the JST connector are marked 'nc'.]

2.3 AiM kit for Solo 2 DL (CAN cable + bracket)

Connection cable for Solo 2 DL and installation bracket can also be bought together with part number: V02589130CS.

2.4 AiM cable for EVO4S and ECULog

Part number of EVO4S and ECULog connection cable for Ducati Panigale V2 and V4 (Euro5 models only) is: V02585200.

Cable constructive scheme:

[Image description: A diagram showing the cable connections. A 7-pin Binder 712 male connector (solder termination view) connects to a 6-pin JST male connector (contact insertion view). The connections are: White wire: CAN1+, Blue wire: CAN1-, Red wire: K Line, Black wire: GND. Pins 3, 4, 5 on the Binder connector are marked 'nc' (not connected). Pins 4, 5, 6 on the JST connector are marked 'nc'.]

3 Solo 2 DL, EVO4S and ECULog connection

To connect Solo 2 DL, EVO4S and ECULog to the bike ECU, use the standard OBDII Euro 5 red connector placed under the bike seat.

Open the bike seat and remove the cap from the red connector, then plug the specific AiM cable.

[Image description: A close-up view of the red OBDII connector located under the motorcycle seat, with an orange circle highlighting it.]

4 Configuration with RaceStudio 3

Before connecting AiM devices to the bike ECU, set all functions using RaceStudio 3 software. The parameters to set in the device configuration ("ECU Stream" tab) are:

• ECU Manufacturer: DUCATI
• ECU Model: PANIGALE V4 (RaceStudio3 only)

After this first selection, enable the "Silent on CAN Bus" checkbox.

[Image description: A screenshot of the RaceStudio 3 software interface showing the "ECU Stream" tab. The selected ECU is "DUCATI - PANIGALE V4 (ver. 02.00.10)". The "Enabled Channels" are listed as 31/31. The "Change ECU" button is visible. Below this, a checkbox labeled "Silent on CAN Bus" is shown, with an option to "Enable the CAN Bus 120 Ohm Resistor".]

5 "Ducati – PANIGALE V4" protocol

Channels received by AiM devices configured with "Ducati – PANIGALE V4" protocol are:

Technical note: Not all data channels outlined in the ECU template are validated for each manufacturer model or variant; some of the outlined channels are model and year specific, and therefore may not be applicable.