Canon Canada Customer Support Home Page
cam.start.canon
Instructions for Canon models including: RF 16mm, F2.8 STM Lens, RF 16mm F2.8 STM Lens, STM Lens, Lens
Canon RF 16mm f/2.8 STM Ultra-wide-angle prime lens for Canon R Series mirrorless cameras at Crutchfield
File Info : application/pdf, 22 Pages, 3.11MB
DocumentDocumentInstructions ENG Thank you for purchasing a Canon product. Canon RF16mm F2.8 STM is a ultra-wide lens for use with EOS R series cameras. z "STM" stands for Stepping Motor. Conventions used in these instructions Warning to prevent lens or camera malfunction or damage. Supplementary notes on using the lens and taking pictures. Camera Firmware and Camera Applications Please use the latest versions of firmware and applications with the camera in use. For details on whether the firmware and applications in use are the latest version or not, and for details on updating them, please check the Canon website. If the camera's* firmware is not a compatible version, the following limitations will apply. z Magnified view functionality is not available. z In some cases, the camera malfunction may occur. * Applies to the following camera models: EOS R and EOS RP ENG-1 Safety Precautions Precautions to ensure that the camera is used safely. Read these precautions thoroughly. Make sure all details are observed in order to prevent risks and injury to the user and other people. Warning Details pertaining to risks that may result in death or serious injury. z Do not look directly at the sun or other strong light sources through a lens. This may result in loss of sight. z Do not leave a lens in the sun without the lens cap attached. The lens may concentrate entering sunlight and cause a malfunction or fire. Details pertaining to risks that may Caution result in injury or damage to other objects. z Do not leave the product in places exposed to extremely high or low temperatures. The product may cause burns or injury when touched. ENG-2 General Precautions Handling Precautions z Do not leave the product in excessive heat such as in a car in direct sunlight. High temperatures can cause the product to malfunction. z If the lens is taken from a cold environment into a warm one, condensation may develop on the lens surface and internal parts. To prevent condensation in this case, first put the lens into an airtight plastic bag before taking it from a cold to warm environment. Then take out the lens after it has warmed gradually. Do the same when taking the lens from a warm environment into a cold one. z Please also read any lens related handling precautions listed in your camera's instruction manual. Shooting Precautions When the camera recovers from the auto power off status to the shooting-ready status, the front end of the lens moves in both AF/MF mode and an initial reset is performed on the focus lens. z Do not shoot until the initial reset is completed. z Focus again after recovering from the auto power off status. z To maintain the focus position in the shooting-ready status, set [Auto power off] to [Disable] on the camera. ENG-3 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. CAN ICES-3 (B) / NMB-3 (B) ENG-4 Nomenclature Hood mount ( 9) Focusing/control ring ( 7) Filter mounting thread ( 10) Focusing/control selector switch ( 7) Lens mount index ( 6) Contacts ( 6) Lens mount ( 6) z For detailed information, reference page numbers are provided in parentheses ( **). ENG-5 1. Attaching and Detaching the Lens Lens mount index Lens release button Dust cap Attaching the Lens Align the lens mount indexes of the lens and camera, and turn the lens clockwise until you hear a click. Detaching the Lens Turn the lens counterclockwise while pressing the camera's lens release button. Detach the lens once it has stopped turning. z Set the camera's power switch to OFF when attaching or detaching the lens. z Attach the lens cap before detaching the lens from the camera. z When the power switch of the camera is set to OFF, the focus lens pushed forward is automatically stored.* Do not detach the lens until the lens is completely stored. z After detaching the lens, place the lens with the rear end up and attach the dust cap to prevent the lens surface and contacts from getting scratched. Make sure the lens and dust cap mount indexes are aligned when attaching the dust cap. z Contacts that are scratched, soiled, or have fingerprints on them may result in faulty connections or corrosion, which may lead to malfunctions. If the contacts get soiled, clean them with a soft cloth. * When the lens storage is set to ON on the camera. Please refer to the camera's instructions for details. ENG-6 2. Focusing/control ring The focusing/control ring can be used as either a focusing ring or a control ring. Focusing/control ring Focusing/control selector switch Use as a Focusing Ring Set the focusing/control selector switch to FOCUS. Set the focus mode (AF/MF) using the camera's menu. To shoot in autofocus (AF) mode, set the camera's focus mode to AF. To use only manual focusing (MF), set the camera's focus mode to MF, and focus by turning the focusing ring (focusing/control ring). z This lens does not have a focus mode switch. z Delayed focus may occur if the focusing ring (focusing/control ring) is quickly turned. z Do not touch the operating part in the front of the lens while the focus lens is operating. If external pressure is applied to the moving part, the lens initialization may be performed to return the focus lens to the correct position for control purposes. z The lens' focusing ring (focusing/control ring) is electronic. z It is possible to set cameras that support electronic fulltime manual focusing to constant manual focusing when the camera is in the operational mode. However, the camera settings need to be changed. z When AF operation is set to [ONE SHOT], manual focus is possible after autofocusing has been completed by continuing to press the shutter button halfway. However, the camera settings need to be changed. Please refer to the camera's instructions for details. ENG-7 Focusing/control ring The focusing/control ring can be used as either a focusing ring or a control ring. Focusing/control ring Focusing/control selector switch Use as a Control Ring Set the focusing/control selector switch to CONTROL. Set the control ring function using the camera's menu. The control ring can be assigned the functions that are commonly used with cameras, such as shutter speed and aperture settings. Please refer to the camera's instructions for details on how to use the control ring. ENG-8 3. Hood (Sold separately) The custom lens hood reduces unwanted light that causes flare and ghosting and protects the front of the lens from rain, snow, and dust. Attachment position mark Red dot Button Red dot Red dot Attachment position mark Stop position mark Attaching the Hood Align the red attachment position mark on the hood with the red dot on the front of the lens, and then turn the hood in the direction of the arrow until you hear a click. Detaching the Hood Keep your finger pressed down on the button located on the side of the hood, and then turn the hood in the direction of the arrow until the attachment position mark on the hood is aligned with the red dot on the front of the lens to detach it. The hood can be reverse-mounted on the lens for storage. z If the hood is not attached properly, vignetting (darkening of the perimeter of the picture) may occur. z Grasp and turn the base of the hood when attaching and detaching it. There are cases in which it may become deformed if the hood is turned with it grasped near to the rim. ENG-9 4. Filters (Sold separately) You can attach filters to the filter mounting thread on the front of the lens. z Only one filter may be attached. ENG-10 Specifications Focal Length/Aperture 16mm f/2.8 Lens Construction 7 groups, 9 elements Maximum Aperture f/2.8 Minimum Aperture f/22 Angle of View Horizontal: 98°, Vertical: 74° 10', Diagonal: 108° 10' Min. Focusing Distance 0.13 m/0.43 ft. Max. Magnification 0.26x Field of View Approx. 135 x 90 mm/5.31 x 3.54 in. (at 0.13 m/0.42 ft.) Filter Diameter 43 mm Max. Diameter and Length Approx. 69.2 x 40.2 mm/2.72 x 1.58 in. (When the lens is retracted) Weight Approx. 165 g/5.8 oz. Hood EW-65C (Sold separately) Lens Cap E-43 Case LP1014 (Sold separately) ENG-11 Specifications z The lens length is measured from the lens mount surface to the front end of the lens. Add +23.4 mm/0.92 in. when including the lens cap and dust cap. z The maximum diameter, length and weight listed are for the lens itself only. z You cannot use extenders. z Close-up Lens 250D/500D cannot be attached because there is no size that fits the lens. z This lens cannot be used for multiple exposure shooting. z There are cases in which using the zoom function during continuous shooting may result in conspicuous image distortion. z All data listed is measured according to Canon standards. z Product specifications and appearance are subject to change without notice. ENG-12 CT1-D228-A 0721Ni © CANON INC. 2021 1111111111111111111111111111111111 CT1 B076A CT1-8076-A © CANON INC. 2018 PRINTED IN TAIWAN Canon Interchangeable Lens Instructions These instructions describe important safety notes for Canon interchangeable lenses* and basic instructions on how to handle those lenses. For more detailed information, refer to the instructions for each lens. Instructions for your lens can be downloaded from the Canon website below: *EF (EF-S) lenses, EF-M lenses, RF lenses http://www.canon.com/icpd/ Refer also to the instructions for the camera. Be sure the latest version firmware is installed in the camera. & Warning Details pertaining to risks that may result in death or serious injury. · Do not look directly at the sun or other strong light sources through a lens or a single-lens reflex camera with a lens attached. This may result in loss of sight. · Do not leave a lens in the sun without the lens cap attached. The lens may concentrate entering sunlight and cause a malfunction or fire. · Do not point a lens at the sun. Even when the sun does not appear on the screen, the lens may concentrate entering sunlight and cause a malfunction or fire. · Where the lens is equipped with a fixed tripod mount and the lens is mounted on a camera, make sure to properly support the lens. If you hold only the camera, the lens may fall off the camera and cause a malfunction or injury. · Where the lens is equipped with a detachable tripod mount, ensure that the tripod mount is securely attached to the lens body. If the tripod mount is not secure, the lens may fall off the tripod mount and cause a malfunction or injury. & Caution Details pertaining to risks that may result in injury. · Do not leave the product in places exposed to extremely high or low temperatures. The product may cause burns or injury when touched. · Do not insert your hand or fingers into the product. This may result in injury. · When using lenses equipped with Macro Lites, do not hold the Macro Lites close to the eyes or stare at them when they are illuminated. Doing so may result in eye damage. · Only mount the product on a tripod that is sufficiently sturdy. Canon ®(O ·_.'\at(&Rj ' ·_,·_.'__·_.·..._@ ® (J) ' CD PF @ ([illIT]; CD @) Attaching and Detaching a Lens Attaching the Lens Align the lens mount indexes on the lens and the camera body and then turn the lens clockwise. Detaching the Lens Hold down the lens release button on the camera and turn the lens counterclockwise. Refer to the camera's instructions for details on attaching and detaching a lens. Shooting Using Autofocus (AF) · To shoot images using autofocus, set AF as the focus mode. · To shoot images using manual focus, set MF as the focus mode and focus by turning the focusing ring. The procedures for setting the focus mode are explained below. DEF (EF-S) lenses and RF lenses: Use the focus mode switch on the lens (AF/MF). DEF-M lenses: Select the setting on the camera ([AF/MF]). Using the Image Stabilizer · To use image stabilization, set the Image Stabilizer to ON. The Image Stabilizer settings are explained below. DEF (EF-S) lenses and RF lenses: Use the Image Stabilizer switch on the lens (ON/OFF). D EF-M lenses: Select the setting on the camera ([ON/OFF]). Attaching a Lens Hood Align the hood with the edge of the lens and turn the hood clockwise to attach it. Using the Control Ring This only applies to RF lenses equipped with a control ring. Refer to the camera's instructions for information on using the control ring. Nomenclature CD Lens mount index ® Focus mode switch @ Focusing ring @Zoom ring @ Image stabilizer switch @ Image stabilizer mode selector switch MODE 1: Corrects vibrations in all directions. MODE 2: When you take a panning shot either horizontally or vertically, corrects vibrations at right angles to the direction of panning. MODE 3: Corrects vibration only during exposure. (J) Focusing distance range selector switch Selects the focusing distance range. @ Tripod mount (fixed-mount type) Used to attach a tripod or monopod. @Tripod mount (detachable tripod type) Used to attach a tripod or monopod. @) Lens-retraction switch Push the switch in the "A " direction while turning the ring to set the lens to the ready position. @ Lock release switch Push the switch in the ·A " direction while turning the ring to set the lens to the ready position. @ Macro Lite ON button Used to change the Macro Lites illuminated patterns. @Macro Lites Illuminate the subject @Lens cap @ Dust cap @ Hood (bayonet type) @ Hood (screw type) @ Control ring l This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received , including interference that may cause undesired operation. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Consult the dealer or an experienced radio/TV technician for help. ____J Complete this card at time of sale. A remplir au moment de l'achat 11 I I I CT1B021A PRESENT OWNERSHIP AND PRODUCTS INTERESTED IN Articles deja en possession ou juges dignes d'inter~t CAMERAS APPAREi LS -PHOTO (Camera) (Appareil) (Camera) (Appareil) (Lens) (Objectif) (Lens) (Objectif) INTERCHANGEABLE LENS OWNS INTERESTED IN Objectif interchangeable En possession lnteresse par · OWNS INTERESTED IN En possession lnteresse par · · · · OTHER ACCESSORIES Autres accessoires OWNS INTERESTED IN En possession lnteresse par · · · MODEL Modele RF16/2.8 STM 0 2 CUSTOMER Client NAME Norn - - - - - - -- ADDRESS - - - - - Adresse CITY/STATE ZIP PHONE Ville/Province - - - - - - - - - - - - - - - Code postal - - - - - - - Telephone - - - - - - - - CANON U.S.A., INC. CANON CANADA INC. NAME NOM ADDRESS ADRESSE CITY VILLE PROVINCE POSTAL CODE CODE POSTAL THESE ARE NOT REGISTRATION CARDS - Retain for your Records CES CARTES NE SONT PAS GELLES POUR L'.ENREGISTREMENT. - Les conserver comme reference. DEALER'S NAME & ADDRESS MARCHAND NOM & ADRESSE MODEL MODELE BODY NO. BOITIER NO RF1 6/2.8 STM 0802003842 CT1-B021-A PURCHASE DATE DATE D'ACHAT I I PRINTED IN TAIWAN IMPRIME ATAIWAN Canon Garantie limitee des objectifs EF et des accessoires de CANON®Pour les Etats-Unis et le Canada seulement a La presente garanlie limitee est fournie par Canon U.S.A., Inc.(Canon U.S.A.) aux Etats-Unis ou Canon Ganada, Inc. (Canon Canada) au Ganada regard des objectifs EF de marque Canon, des accessoires livres avec cette garantie limitee (coUectivement les" produ1ts ·), lorsqu'ils sont achetes et utilises aux Etats-Ums ou au Canada Les produrts sont les seuls auxquels cette garantie hmitee s'appllque. a a Tout produit, livre retat neuf clans son emballage d'orig1ne, est garanti contra tout vice de matiere et de fabncation comma suit :pendant une periode de un (1) an compter de la date de l'achat initial, les pieces ou les produits defectueux qui seront retournes aCanon U.S.A. ou Canon Canada, ou aleurs fourn1sseurs de service agree de produits, selon le cas, et dont l'mspection conf1rme une defectuosite seront repares avec de nouvelles pieces ou des pieces rem1Ses aneuf comparables, ou echanges contra des produits rem1s aneuf, tel que determine par Canon U.S.A. ou canon Canada, ou le fournisseurde service agree de produits. CETTE GARANTIE NE COUVRE PAS LES ACCESSOIRES QUI NE SONT PAS MENTIONNES CI-DESSUS. La presente garantie limitee s'apphque seulement si les produ1ts sont utilises conjointement avec un equ1pement informatique compatible et des logiciels compatibles, pour lesquels Canon U.S.A. ou Canon Canada n'assume aucune respoosabilite. t:equipement et les loglciels de marques autres que Canon qui peuvent etre distribues avec les produits sont vendus « tels quels », sans garantie d'aucune sorta par Canon U.S.A. ou Canon Canada, ycompris toute garantie impliclte al'egard de la quaiite marchande ou de !'aptitude aune fin particuliere. La seule garantle, si garantle ii y a, iiee aun article d'une marque autre que Canon, est donnee par le fabricant ou le producteur de cet article. La presente garantie limitee couvre toutes les defectuosites constatees pendant !'utilisation normale du produit, et ne s'apphque pas aux cas suivants · a (a) la perte ou l'endommagement cause par la negligence et(ou) l'usage abus1f et entrainant une deterioration, la manipulation negligente, les accidents ou !'omission d'observer les directives regard du mode d'utiiisation. a (b) La defaillance du produit la suite d'une fuite des piles ou l'endommagement par l'eau ou d'autres liqu1des. (c) Les vices de matiere et de fabrication causes par l'entret1en ou la modification du produit par un fournisseur de service autre qu'un fournisseur de service agree de Canon ou par Canon. (d) la defaillance causee par l'utilisation d'accessoires, de fournitures, de pieces ou d'appareils (y compns, ma1s sans s'y hm1ter, les piles, les films, les accessoires flash et les autres accessoires) qui ne sont pas conformes aux caracteristiques de Canon (e) l..'.endommagement survenu pendant !'expedition. (La demande doit l!tre presentee et verifiee par l'expedlteur.) (f) l..'.endommagement ou l'entretien cause par des modifications apportees au produil, quelles qu'elles soient (y compris la modification ou le retrail du numero de serie ou des marques d'identification). AUCUNE GARANTIE IMPLICITE, Y COMPRIS TOUTE GARANTIE IMPLICITE AL:EGARD DE LA QUALITE MARCHANDE OU DE !.:APTITUDE AUNE FIN PARTICULIERE, NE S'APPLIQUE AU PRODUIT APRES LA PERIODE PRESCRITE DE LA GARANTIE EXPRESSE RESTREINTE SUSMENTIONNEE ET, Al..'.EXCEPTION DE LADITE GARANTIE EXPRESSE RESTREINTE, AUCUNE AUTRE GARANTIE EXPRESSE NI AUCUNE AUTRE GARANTIE ACCORDEE PAR TOUTE PERSONNE OU ENTITE Al..'.EGARD DU PRODUIT N'AURA POUR EFFET DE LIER CANON ATOUTE OBLIGATION, QUELLE QU'ELLE SOIT (CERTAINS ETATS ET CERTAINES PROVINCES N'AUTORISENT AUCUNE RESTRICTION SUR LA DUREE D'UNE GARANTIE IMPLICITE ; AINSI, IL EST POSSIBLE QUE LA RESTRICTION ENONCEE CI-DESSUS NE S'APPLIQUE PAS DANS VOTRE CAS). CANON N'ASSUME AUCUNE RESPONSABILITE Al..'.EGARD DE LA PERTE DE PRODUITS D'EXPLOITATION OU DE PROFITS, NI Al..'.EGARD DES INCONVENIENTS ET DES FRAIS ENGAGES POUR DE l..'.EQUIPEMENT DE REMPLACEMENT, DES SERVICES D'ENTRETIEN ET APRES-VENTE, POUR L:ENTREPOSAGE, LA PERTE OU LA CORRUPTION DE DONNEES, NI Al..'.EGARD DE TOUT DOMMAGE SPECIAL, INDIRECT OU ACCESSOIRE (Y COMPRIS, MAIS SANS S'Y LIMITER, LA PERTE DE FILMS) DECOULANT DE 1..'.USAGE OU DE l..'.USAGE IMPROPRE, OU D~ l..'.IMPOSSIBILITE D'UTILISER LE PRODUIT, QUELLE QUE SOIT l..'.ARGUMENTATION JURIDIQUE SUR LAQUELLE S'APPUIE LA DEMANDE, ET M~ME SI CANON A ITT INFORMEE DE LA POSSIBILITE DE TELS DOMMAGES. EN AUCUN CAS, AUCUN RECOUVREMENT, QUELLE QU'EN SOIT LA FORME, CONTRE CANON NE SERA SUPERIEUR AU MONTANT OU PRIX D'ACHAT DU PRODUIT VENDU PAR CANON ET Al..'.ORIGINE DES DOMMAGES PRESUMES. SANS VOUS LIMITER A CE QUI PRECEDE, VOUS ASSUMEZTOUS LES RISQUES ETTOUTE LA RESPONSABILITE Al..'.EGARD DES PERTES, DES DOMMAGES MATERIELS ET DES BLESSURES CORPORELLES SUBIS PAR VOUS, VOTRE PROPRIETE OU D'AUTRES PERSONNES OU LEUR PROPRIETE EN RAISON DE l..'.USAGE. DE 1..'.USAGE IMPROPRE, OU DE L:IMPOSSIBILITE D'UTILISER LE PRODUIT A MOINS QUE LESDITS DOMMAGES MATERIELS, PERTES ET BLESSURES CORPORELLES N'AIENT ETE CAUSES DIRECTEMENT ET EXCLUSIVEMENT PAR LA NEGLIGENCE DE CANON (CERTAINS ETATS ET CERTAINES PROVINCES N'AUTORISENT AUCUNE EXCLUSION NI RESTRICTION DES DOMMAGES ACCESSOIRES OU INDIRECTS ; AINSI, IL EST POSSIBLE QUE LA RESTRICTION OU l..'.EXCLUSION ENONCEE CI-OESSUS NE S'APPLIQUE PAS DANS VOTRE CAS). LA PRESENTE GARANTIE RESTREINTE N'EST PAS ACCORDEE AD'AUTRES PERSONNES QUE 1..'.ACHETEUR INITIAL DU PRODUIT OU LA PERSONNE QUI A REQU LEDIT PRODUIT EN CADEAU, ET CONSTITUE VOTRE RECOURS EXCLUSIF a a La presente garantie limitee vous accorde des droils particuliers reconnus par la loi et ii se peut que vous disposiez d'autres droits qui peuvent varier d'un Etat un autre (ou d'une province une aulre au Canada). Canon U.S.A.,lnc. Canon Canada Inc. Canon U.S.A. You may obtain technical support for your Products as follows: · Internet support at www.usa.canon.com/support (E-mail support also available) · Telephone assistance from a Canon U.S.A. Customer Care representative free of charge during regular business hours at 1-800-OK-CANON (1-800-652-2666). Canon Canada You may obtain technical support for your Products as follows: · Internet support for English at www.canon.ca/english/cs (E-mail support also available} · Internet support for French at www.canon.ca/francais/cs (E-mail support also available) · Telephone assistance from a Canon Canada Customer Care representative free of charge during regular business hours at 1-800-OK-CANON (1-800-652-2666). Des services de soutien technique pour vos produits sont offerts comme suit : · Soutien Internet en anglais au moyen du site Web : www.canon.ca/engllsh/cs (Soutien par courrier electronique aussi disponible) · Soutien Internet en fran<;ais au moyen du site Web : www.canon.ca/francais/cs (Soutien par courrier electronique aussi disponible) · Soutien telephonique aupres d'une representante ou d'un representant du Centre de renseignements clientele de Canon Canada, sans frais, pendant les heures normales d'ouverture au 1-800-OK-CANON (1-800-652-2666). Technical support program terms are subject to change without notice. Les conditions du programme de soutien technique sont modifiables sans preavis. Canon U.S.A., Inc. Canon Canada, Inc. Ca11011 CANON®EF Lens and Accessories Limited WarrantyFor U.S.A. & Canada Only The limited warranty set forth below is given by Canon U.S.A., Inc. (Canon U.S.A.) in the United States or Canon Canada, Inc. (Canon Canada) in Canada with respect to the Canon brand EF Lens, as well as with respect to the accessories packaged with this hm1ted warranty (collectively the "Products"), when purchased and used in the United States or Canada. The Products are the only Products to which this limited warranty applies. Your Products, when delivered to you in new condition in its original container, are warranted against defects In materials or workmanship as follows: for a period of one (1) year from the date of original purchase, defective parts or defective Products returned to Canon U.S.A. or Canon Canada, or their authorized Products service providers, as applicable, and proven to be defective upon inspection, will be repaired with new or comparable rebuilt parts or exchanged for refurbished Products, as determined by Canon U.S A or Canon Canada, or the authorized Products service provider. THIS WARRANTY DOES NOT COVER ANY ACCESSORIES NOT MENTIONED ABOVE. This limited warranty shall only apply if the Products are used in conjunction w ith compatible computer equipment and compatible software, as to which items Canon U.S.A. or Canon Canada shall have no responsibility. Non-Canon brand equipment and software that may be distributed with the Products are sold "as is" and without warranty of any kind by Canon U.S.A. or Canon Canada, Including any implied warranty regarding merchantability or fitness for a particular purpose, and all such warranties are disclaimed. The sole warranty, If any, with the respect to such non-Canon brand Items Is given by the manufacturer or producer thereof. This limited warranty covers all defects encountered in normal use of the Products, and does not apply in the following cases: (a) Loss or damage due to neglect and/or abuse causing deterioration, mishandling, accident or failure to follow operating instructions. (b) If a Product is defective as a result of leaking batteries or damage due to water or other liquid. (c) Defective materials or workmanship where the defect is due to a Product having been serviced or modified by other than Canon or a Canon authorized service provider. (d) Malfunction resulting from the use of accessories, attachments, supplies, parts or devices (including, without limitation, batteries, film, flash attachments and other accessories) that do not conform to Canon specifications. (e) Damage resulting during shipment. (Claim must be presented and examined by the shipper). (f) Damage or service resulting from modifications or alterations to a Product in any way (including any alteration or removal of its serial number or identification marks). NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, APPLIES TO A PRODUCT AFTER THE APPLICABLE PERIOD OF THE EXPRESS LIMITED WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY, EXCEPT AS MENTIONED ABOVE , GIVEN BY ANY PERSON OR ENTITY WITH RESPECT TO A PRODUCT SHALL BIND CANON (SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU). CANON SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, INCONVENIENCE, EXPENSE FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, ANY LOSS OF FILM) CAUSED BY THE USE OR MISUSE OF, OR INABILITY TO USE, A PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL RECOVERY OF ANY KIND AGAINST CANON BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY CANON AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY ANO TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE OR MISUSE OF, OR INABILITY TO USE, THE PRODUCT NOT CAUSED SOLELY AND DIRECTLY BY THE NEGLIGENCE OF CANON (SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU). THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF A PRODUCT, OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT. AND STATES YOUR EXCLUSIVE REMEDY. This limited warranty gives you specific legal rights, and you may also have other rights, which vary from state to state (or province to province 1n Canada). Canon U.S.A., Inc. Canon Canada, Inc. Register Now! l:-' Visit www.registercanon.com to register your new EF & EF-S Lenses today and receive the following: · Telephone support* · E-mail support* · Product protection* · Receive information on new products and promotions* There is no charge to register orfor the benefits offered. * These benefits valid in the U.S. only. Please read the Terms and Conditions at www.registercanon.com for complete details. -- For accessories and other supplies visit www.estore.usa.canon.com or an Authorized Canon Dealer. Canon © 2016 CANON U.S.A., INC.