Fender Player Telecaster Left Hand (014-5222-XXX/014-5223-XXX)

Parts Layout

Diagram showing a front and back view of the Fender Player Telecaster Left Hand guitar with numbered callouts pointing to various components.The front view displays the headstock with tuning machines (5, 6, 7, 8, 9) and nut, the neck with frets, the body with neck pickup (2), bridge pickup (1), pickguard (11, 12, 13), control knobs (26), switch (23), volume (21) and tone (22) potentiometers, bridge assembly (17), strap button (14), and string ferrules (10).The back view shows the neck plate (3, 4), control plate (13), and strap button (14).

Key components indicated by numbers:

• 1: Bridge Pickup
• 2: Neck Pickup
• 3: Neck Plate
• 4: Neck Plate Screw
• 5: String Guide
• 6: Tuning Machine Screw
• 7: Tuning Machine (Key)
• 8: Tuning Machine Washer
• 9: Tuning Machine Bushing
• 10: String Ferrules
• 11: Pickguard
• 12: Pickguard Screws
• 13: Control Plate
• 14: Strap Button
• 15: White Felt Washer (Strap Button)
• 16: Bridge Mounting Screws
• 17: Bridge Assembly
• 18: Bridge Pickup Assembly
• 19: Pickup Mounting Tubing (Latex)
• 20: Pickup Mounting Screws
• 21: Volume Control Potentiometer
• 22: Tone Control Potentiometer
• 23: 3-Way Switch
• 24: Pickup/Switch Screws
• 25: Switch Tip
• 26: Control Knobs (Volume/Tone)
• 27: Screw Set (General)
• 28: Volume/Tone Control Shaft
• 29: Lock Washer
• 30: Control Shaft Nut
• 31: Output Jack Assembly
• 32: Output Jack Ferrule

Parts List

Wiring Diagram

The wiring diagram illustrates the internal electrical connections of the Fender Player Telecaster Left Hand. It shows the pathways from the neck pickup and bridge pickup to the 3-way selector switch. The switch output is connected to the volume control. The tone control, paired with a 0.05µF capacitor, is also integrated into the circuit, typically affecting the signal before or after the volume control. The final signal is routed to the output jack. Wires are depicted in black, white, and green.

Key components shown:

• Neck Pickup
• Bridge Pickup
• 3-Way Switch
• Volume Control
• Tone Control
• Capacitor (.05µF)
• Output Jack

Connections are made between these components to facilitate pickup selection and signal processing.

Switch and Control Function

The 3-way selector switch controls which pickup(s) are active:

• Position 1: Neck Pickup ON
• Position 2: Bridge Pickup ON
• Position 3: Both Neck and Bridge Pickups ON

The diagram uses red lines to indicate when a pickup is ON and white lines when it is OFF, corresponding to the 3-way switch position.

Controls include:

• Neck Pickup
• Bridge Pickup
• 3-Way Switch
• Master Volume
• Master Tone

Additional Specification Detail

Fret Size

Medium Jumbo

(Fret dimensions are before installation)

Neck Dimensions and Profiles

Note: Neck thickness dimensions may vary slightly due to hand sanding and finishing.

• Headstock Outer Shaft Diameter (Tuning Machine): .394"
• Tuning Machine Thru-Hole Inner Diameter: .397"
• Neck Profile (approximate): .820" at headstock, .870" at 1st fret.

Hardware and Tools

• Key Guitar LH Dual Pin Mount P/N: 0073119000
• Saddle Height Adjustment Wrench: 1/16" Hex Key
• Truss Rod Nut P/N: 0038454000 (10-32 Thread)
• Saddle Height Adjustment Screw: Tall: .396", Short: .3165"

Logo: Decal Fender Telecaster LH applied under the finish.

Pickup Specifications