GPU Option Kit Installation Guide
Introduction
This guide provides instructions for installing GPU Option Kits into compatible server systems. It covers various GPU types from NVIDIA, AMD, and Intel, including different slot configurations and specific models.
Supported Configurations
The following configurations are supported:
- NVIDIA | AMD: Single Slot x16 GPUs
- NVIDIA | AMD | Intel Gaudi3: Dual Slot x8 GPUs
- NVIDIA: Dual Slot x4 GPUs (e.g., H200, RTX Pro 6000)
- NVIDIA NVLINK Bridge: For connecting multiple GPUs
Note on Slotting: Systems typically feature multiple PCIe slots, often categorized as Slot 1/2/7/8 and Slot 3/4/5/6, depending on the server chassis design.
General Installation Steps
The following steps outline the general procedure for installing GPU option kits, which may vary slightly based on the specific GPU and chassis. Always refer to the applicable models listed for your system.
Installation for NVIDIA (Dual Slot x4 GPUs | H200 x1) and NVIDIA (Dual Slot x4 GPUs | RTX Pro 6000 | Non-Vented Bracket)
Applicable Models: G294-A21 / S41 / S45 / Z21 / Z41
- Step 1: Remove Original Bracket
Remove the original vented bracket from the designated PCIe slot. ?️ [Remove Bracket] - Step 2: Install New Brackets
Install two solid (non-vented) brackets in place of the removed ones. These brackets are typically part of the GPU option kit or chassis. ? [Install Brackets] - Step 3: Secure Brackets
Secure the new brackets firmly using the provided screws on both the inner and outer sides. ? [Secure Brackets] - Step 4: Verify Installation
Ensure the bracket is properly installed and firmly fixed in place. ✔️ [Verify Installation]
Installation for NVIDIA (Dual Slot x4 GPUs, NVIDIA NVLINK Bridge | H200 x2)
Applicable Models: G294-A22 / S42 / Z22 / Z42
This configuration involves installing GPUs and an NVIDIA NVLINK Bridge to enable high-speed interconnectivity between compatible NVIDIA GPUs.
Installation Steps:
- Install the GPU option kits as per the general steps outlined above.
- Connect the NVIDIA NVLINK Bridge between the installed GPUs. Ensure the bridge is seated correctly on the NVLINK connectors of both GPUs. ? [NVLink Bridge]
Note: The NVLINK Bridge requires specific GPU models and server configurations. Refer to NVIDIA documentation for compatibility details.
Installation for NVIDIA (Dual Slot x4 GPUs | RTX Pro 6000 | Vented Bracket)
Applicable Models: G294-A21 / S41 / S45 / Z21 / Z41
This section details the installation of NVIDIA RTX Pro 6000 GPUs, which may utilize a specific type of bracket as part of the kit.
- Step 1: Remove Original Bracket
Remove the original vented bracket from the designated PCIe slot. ?️ [Remove Bracket] - Step 2: Install New Brackets
Install two solid (non-vented) brackets in place of the removed ones. ? [Install Brackets] - Step 3: Secure Brackets
Secure the new brackets firmly using the provided screws on both the inner and outer sides. ? [Secure Brackets] - Step 4: Verify Installation
Ensure the bracket is properly installed and firmly fixed in place. ✔️ [Verify Installation]
Note: While the subtitle mentions "Vented Bracket", the explicit instruction is to install "solid (non-vented) brackets". This likely refers to the chassis slot brackets being replaced by solid ones from the kit, or the GPU itself having a specific bracket type.
Single Slot x16 GPUs and Dual Slot x8 GPUs
For NVIDIA/AMD Single Slot x16 GPUs and NVIDIA/AMD/Intel Gaudi3 Dual Slot x8 GPUs, the installation process involves selecting the appropriate PCIe slot and installing the GPU according to its specific mounting mechanism and power requirements. Detailed bracket steps may vary.
Important Considerations
- Always ensure the system is powered off and unplugged before installation.
- Ground yourself to prevent electrostatic discharge (ESD).
- Refer to your server's documentation for specific slot assignments and compatibility.
- Ensure adequate cooling and power supply for the installed GPUs.
