VIVO RV TV Mount Set

Important Safety Information

CAUTION!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact VIVO product support at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY

FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.

We're Here for You

VIVO support is available Monday - Friday, 7:00 am - 7:00 pm CST. Our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact VIVO. We are happy to replace parts to ensure you have a fully functioning product.

Package Contents

• A (x2): Wall Plate
• B (x1): VESA Plate

Included Hardware & Tools

Hardware:

• M-A (x4): M4 Washer
• M-B (x4): M4x12mm Screw
• M-C (x4): M5x12mm Screw
• M-D (x4): M6x12mm Screw
• W-A (x12): ST6x30mm Stainless Steel Screw

Tools Needed:

• Pencil
• Phillips Screwdriver
• Power Drill
• 1/8" (3mm) Drill Bit
• Level

Weight Capacity

30 lbs (13.6 kg)

Installation Locations

The TV mount can be installed on the inside or outside of an RV or camper wood stud walls. If mounting on an RV, locate the designated mounting location, which should be pre-labeled by the manufacturer as "TV BACKER" or "TV MOUNTING LOCATIONS". Refer to the RV manufacturer for more information.

[Diagram Description: An illustration showing the interior of an RV with a marked area indicating the "DESIGNATED MOUNTING LOCATION" on a wall.]

IMPORTANT NOTE: The TV should be ALWAYS removed from the wall and securely stowed away while the RV/camper is in motion.

Assembly Steps

STEP 1: Mount Wall Plate

Hold Wall Plate (A) up to the desired mounting location and mark hole locations using a pencil. Use of a level is highly recommended. If mounting in an RV, ensure the trailer is level before leveling the mount. Drill marked holes 1.2" (30mm) deep using a 1/8" (3mm) drill bit. Install Wall Plate (A) using ST6x30mm Screws (W-A) and a Phillips screwdriver. Repeat for the second Wall Plate.

[Diagram Description: Illustration showing Wall Plate (A) being attached to a wall with screws (W-A). A ruler graphic indicates 30mm depth and 3mm drill bit diameter.]

STEP 2: Attach VESA Plate to TV

Secure VESA Plate (B) to the TV using appropriate Screws (M-B, M-C, or M-D) and M4 Washers (M-A), along with a Phillips screwdriver. Ensure the "UP" indicator on the VESA plate is in the correct orientation.

[Diagram Description: Two illustrations showing VESA Plate (B) being attached to the back of a TV using different screw types (M-B or M-C/M-D) and washers (M-A). The "UP" indicator is shown.]

STEP 3: Mount TV to Wall Plate

Because of the low-profile design of the mount, any needed cables should be plugged into the TV prior to mounting. Once cables are plugged in, slide the TV with VESA Plate (B) onto the Wall Plate (A).

[Diagram Description: An illustration showing the TV with VESA Plate (B) being slid onto the Wall Plate (A) already mounted on the wall.]

Contact & Support

For further assistance or inquiries:

Follow VIVO on social media: VIVO-us @vivo_us

For more VIVO products, visit our website: WWW.VIVO-US.COM

Last Updated: 12/24/24 | Revision: V1.1 | Version: v1.0