Acuity Brands Lighting
U.S. Environmental Protection Agency | US EPA
Hydrel | Architectural Outdoor Lighting | Acuity Brands
Installation Guide for HYDREL models including: SAF1 Architectural Wall Mount Cover AWMC, SAF1, Architectural Wall Mount Cover AWMC, Wall Mount Cover AWMC, Mount Cover AWMC
Architectural Wall Mount Cover (AWMC) - Designed to be mounted over a recessed wall box. Compatible with SAF1
File Info : application/pdf, 4 Pages, 295.60KB
DocumentDocumentAWMC Installation Manual Installation Guide 1 READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION · To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels. · Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions. · Installation and service of luminaires should be performed by a qualified licensed electrician. · Maintenance of the luminaires should be performed by person(s) familiar with the luminaires' construction and operation and any hazards involved. Regular fixture maintenance programs are recommended. · It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary. · DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced. · Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov. · These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's or owner's purposes, this matter should be referred to Acuity Brands Lighting, Inc. WARNING ! RISK OF ELECTRIC · Disconnect or turn off power before installation or servicing. · Verify that supply voltage is correct by comparing it with the luminaire label information. · Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements. · All wiring connections should be capped with UL approved recognized wire connectors. WARNING ! RISK OF BURN · Disconnect or turn off power before installation or servicing. · Verify that supply voltage is correct by comparing it with the luminaire label information. · Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements. · All wiring connections should be capped with UL approved recognized wire connectors. ! CAUTION · Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance. · Avoid direct eye exposure to the light source while it is on. ! CAUTION · Keep combustible and other materials that can burn, away from lamp/lens. · Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying. NOTE: HYDREL RESERVES THE RIGHT TO MODIFY SPECIFICATION WITHOUT NOTICE. Any dimension on this sheet is to be assumed as a reference dimension: "Used for information purposes only. It does not govern manufacturing or inspection requirements." (ANSI Y14.5-1973) Model AWMC | 11/03/21 | REV ©2019 Hydrel Rev. | One Lithonia Way, Conyers, GA 30012 Phone: 1800.705.SERV (7378) | www.hydrel.com Installation Guide AWMC Installation Manual 2 CAUTION: ! RISK OF PRODUCT · Never connect components under load. · Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation. · Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy sensors, timing devices, or other related control devices. LED fixtures must be powered directly off a switched circuit. · Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling. · Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature. · Only use fixture in its intended location. · LED products are Polarity Sensitive. Ensure proper Polarity before installation. · Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit. · Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance. · Some components inside the fixture may not be serviceable. In the unlikely event your unit may require · service, stop using the unit immediately and contact an ABL representative for assistance. · Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings. Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory statements. Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com. Indoor/Outdoor Lithonia Lighting Carandini Holophane RELOC Indoor Lighting Gotham Mark Architectural Lighting Peerless Renaissance Lighting Winona Lighting Outdoor Lighting American Electric Lighting Antique Street Lamps Hydrel Tersen Controls Dark to Light Lighting Control & Design ROAM Sensor Switch Synergy Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products. ABL LED General Warnings, Form No. 503.203 © 2019 Acuity Brands Lighting, Inc. All rights reserved. 07/31/19 NOTE: HYDREL RESERVES THE RIGHT TO MODIFY SPECIFICATION WITHOUT NOTICE. Any dimension on this sheet is to be assumed as a reference dimension: "Used for information purposes only. It does not govern manufacturing or inspection requirements." (ANSI Y14.5-1973) Model AWMC | 11/03/21 | REV ©2019 Hydrel Rev. | One Lithonia Way, Conyers, GA 30012 Phone: 1800.705.SERV (7378) | www.hydrel.com Installation Guide 1. INTRODUCTION AWMC Architectural Wall Mount Cover 1.1 Product Description Material: Aluminum Outer Diameter Dimension: 4.27 in. (108.5mm) This Architectural Wall Mount Cover is designed to be mounted over a recessed wall junction box and can support one luminaire (light fixture). Suitable for use with Luminaire Model SAF1. AWMC Installation Manual 3 1.2 Technical Information Sources If additional questions arise relative to this luminaire that this document or your supplier cannot answer, please refer then to: Architectural Technical Support Hydrel (888) 834-5684, Press #5 for Hydrel NOTE: HYDREL RESERVES THE RIGHT TO MODIFY SPECIFICATION WITHOUT NOTICE. Any dimension on this sheet is to be assumed as a reference dimension: "Used for information purposes only. It does not govern manufacturing or inspection requirements." (ANSI Y14.5-1973) Model AWMC | 11/03/21 | REV ©2019 Hydrel Rev. | One Lithonia Way, Conyers, GA 30012 Phone: 1800.705.SERV (7378) | www.hydrel.com Installation Guide 2. INSTALLATION Model AWMC may be mounted directly over a recessed wall junction box 2.1 Wall Mounting 1. Secure Luminaire to Cover Plate: Ensure the luminaire gasket is placed between the Luminaire and the Cover Plate. Secure the Luminaire to the Cover Plate using provided Backup Nut (Torque to 30 in-lb). 2. Route Luminaire wires to Junction Box and make all wiring connections. 3. Secure the Cover Plate to the wall surface, or the junction box, using appropriate fasteners; provided by others. Ensure the wall gasket is placed between the Cover Plate and the wall surface. (Torque fasteners to 25 in-lb). 4. Aim luminaire: Loosen adjusting screw on Knuckle Assembly with Allen Wrench (Do not remove adjusting screw completely). Tilt Luminaire to desired angle. Tighten adjusting screw with Allen Wrench, with care not to over tighten screw. AWMC Installation Manual 4 NOTE: HYDREL RESERVES THE RIGHT TO MODIFY SPECIFICATION WITHOUT NOTICE. Any dimension on this sheet is to be assumed as a reference dimension: "Used for information purposes only. It does not govern manufacturing or inspection requirements." (ANSI Y14.5-1973) Model AWMC | 11/03/21 | REV ©2019 Hydrel Rev. | One Lithonia Way, Conyers, GA 30012 Phone: 1800.705.SERV (7378) | www.hydrel.com