Anbit B0611 Bluetooth Transmitter and Receiver User Manual

Product Overview

The Anbit B0611 is a versatile wireless device that functions as both a Bluetooth transmitter and receiver, allowing you to wirelessly stream audio between devices.

Model: B0611

Control Functions

The B0611 features several controls for operation:

• Power On/Off: Press and hold the power button for approximately 1.5 seconds.
• Enter Pairing Mode: After powering on, press and hold the power button for approximately 2.5 seconds. The LED indicator will flash red and blue.
• Volume Up: Short press the VOL+ button.
• Next Track: Long press the VOL+ button.
• Volume Down: Short press the VOL- button.
• Previous Track: Long press the VOL- button.
• Reset Device: Press and hold the power button for approximately 5 seconds.

Mode Selection

The device can operate in two modes, selected via a physical switch:

• TX (Transmitter) Mode: Slide the mode switch to 'TX'. In this mode, the B0611 transmits audio wirelessly from a source device to Bluetooth audio receivers (e.g., headphones, speakers).
• RX (Receiver) Mode: Slide the mode switch to 'RX'. In this mode, the B0611 receives audio wirelessly from a source device (e.g., smartphone, computer) and outputs it to wired audio systems (e.g., amplifiers, speakers).

Instructions

TX Mode Setup

Follow these steps to use the B0611 as a Bluetooth transmitter:

1. Connect the B0611 to a non-Bluetooth audio source device (e.g., a TV) using the included 3.5mm audio cable.
2. Ensure the mode switch is set to 'TX'. After powering on, the adapter will automatically enter pairing mode, indicated by flashing red and blue LED lights.
3. Set your Bluetooth audio receiver (e.g., headphones or speaker) to its pairing mode.
4. Wait for the pairing process to complete successfully.
5. Enjoy wireless audio playback.

RX Mode Setup

Follow these steps to use the B0611 as a Bluetooth receiver:

1. Connect the B0611 to an amplifier or powered speaker using the 3.5mm audio cable.
2. Ensure the mode switch is set to 'RX'. After powering on, the adapter will automatically enter pairing mode, indicated by flashing red and blue LED lights.
3. Activate the Bluetooth function on your audio source device (e.g., mobile phone, computer, or tablet).
4. Search for 'B0611' in your device's Bluetooth settings, tap to connect, and wait for the pairing to succeed.
5. Enjoy wireless audio playback.

Pairing Multiple Devices

Entering Pairing Mode

After powering on the device, press and hold the power button for approximately 2 seconds. The B0611 will enter pairing mode, with the LED lights flashing red and blue.

Pairing a Second Device (RX Mode)

Note: The B0611 can only play music on one connected device at a time. To play music on a second device, you must pause or disconnect the music from the first device.

1. Set the B0611 back into pairing mode by pressing and holding the power button for 2 seconds until the LED flashes red and blue.
2. On the second mobile phone or device, activate Bluetooth, search for 'B0611', and tap 'Connect'. Wait for the pairing to succeed.
3. Enjoy your music.

Charging Method

Connect the provided charging cable to charge the B0611. The LED indicator will light up red during charging.

When the battery is fully charged, the LED indicator will turn off.

How to Reset the Device

If the B0611 cannot be connected or is not functioning normally, you can reset it using the following procedure:

Turn off the B0611. Press and hold the power button for 5 seconds. The purple indicator light will flash 3 times simultaneously, and the device will automatically power on and enter pairing mode.

Audio Codec Support

The B0611 supports the following audio codecs for high-quality wireless audio transmission:

• SBC (Subband Coding)
• aptX (Audio Coding Technology)
• aptX-Adaptive

Note: For optimal performance, the audio codec format must be supported by both the transmitting and receiving devices.

Warranty Information

Anbit provides a warranty service limited to normal product usage. The warranty is void if damages occur due to improper use, such as connecting to an unsuitable power source, using an incompatible device, failing to follow instructions, unauthorized repairs, or modifications. Shipping fees for warranty service are not covered.

Disposal Information

Please dispose of this electronic device responsibly. Do not discard it with regular household waste. Take it to an authorized recycling center for electronic waste.

Compliance and Manufacturer Details

ANET International declares that the B0611 product complies with the essential requirements and relevant provisions of Directive 2014/53/EU.

EC REP: Anet Consulting GmbH, 5 Fankfurter Main, Germany

Operator: Anh Information Ltd, Tsim Sha Tsui Kowloon, Hong Kong

Manufacturer: Shenzhen Anbit Electro, Shenzhen, China

Address: Runfeng Industrial Park No. 4197 Bason Blvd, Henggang St, Longgang Dist., Shenzhen, China

FCC ID: 2AUFR-R15017

This product bears the CE marking.

Made in China

Document Details

Material Name: RT501701 User Manual

Material Number: 07895017020

Material Size: 105mm x 80mm

Version: VER1.4

Production: Winson

Date: 2023/04/19