LiftMaster 375UT Universal Remote Control

STOP

Read instructions thoroughly BEFORE beginning. If using the Universal Remote Control with residential door openers, the Universal Remote Control must be used only with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located on or near the bottom of the door track.

The Universal Remote Control can be programmed to activate up to two products, such as a garage door opener, gate operator, or commercial door operator. Each button on the Universal Remote Control works independently of the other and must be programmed separately. The second button on the Universal Remote Control can be programmed to different products without affecting the first button programmed. The images throughout this manual are for reference only and your product may look different.

WARNING

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

WARNING

This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

PROGRAMMING

1. Start with your garage door, gate, or commercial door closed.

   [Illustration shows a closed garage door or gate.]

2. Open the remote control by sliding the battery cover down. Press and hold the program button until the LED lights (approximately 2 seconds).

   [Illustration shows a hand sliding the battery cover down on the remote control to open it, and pressing the program button until the LED lights up.]

3. Press and release the SMART/LEARN button on your product.

   [Illustration shows a hand pressing the SMART/LEARN button on a garage door opener control board or external receiver.]

4. Press and release the button. When the LED stops flashing, continue to press and release the button until a click is heard from the garage door opener, a light on the garage door opener blinks, the garage door opens/closes, or a beep is heard from the gate operator (maximum 18 times).

   OR

   Press and release the Universal Remote Control button the following number of times for your product's brand and year:

   • 8 times: Chamberlain® Yellow Button (2011-Current)
   • 3 times: Chamberlain® Purple Button (2005-Current)
   • 2 times: Chamberlain® Orange Button (1997-2005)
   • 4 times: Chamberlain® Green Button (1993-1996)
   • 6 times: Genie Overhead Door® Intellicode (1995-Current)
   • 5 times: Genie Overhead Door® Intellicode (2005-Current)
   • 1 time: Linear® Mega-Code (1997-Current)
   • 7 times: Stanley® Security Code (1998)
   • 9 times: Wayne Dalton® Rolling Code 372.5 MHz (1999-Current)
   • 14 times: Linear Multicode® 10 Position Dip Switch
   • 16 times: Stanley Multicode® 10 Position Dip Switch
   • 18 times: Linear® 8 Position Dip Switch

   [Illustration shows a hand pressing a button on the universal remote control. A list details the number of presses required for different brands and years.]

5. Match the remote control DIP SWITCHES to the existing receiver or existing remote control.

   NOTE: The SMART/LEARN button or DIP SWITCHES are located either on the product or in an external receiver on or near the product. Consult your product owner's manual to locate the SMART/LEARN button or DIP SWITCHES.

   NOTE: If you have a 2 position DIP SWITCH and programming fails, reverse DIP SWITCHES (OFF to ON and ON to OFF).

   [Illustration shows a hand matching DIP switches on the remote control to DIP switches on a receiver or existing remote control.]

6. Press the program button to exit programming mode. Programming is now complete.

   The LED on the Universal Remote Control MUST stop blinking between each press of the button. The code is accepted when a click or beep is heard, a light blinks, or the door/gate activates.

   *LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible with Chamberlain technology.

7. Press the programmed button to activate your product. If product does not activate, repeat the programming steps 3-6 again.

   [Illustration shows a hand pressing the programmed button on the universal remote control to activate the product.]

REMOTE CONTROL BATTERY

WARNING

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

• Replace ONLY with 3V CR2032 coin batteries.
• DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.

[Diagram shows the disassembled remote control, highlighting the LED indicator, Button 1, Button 2, Program Button, DIP Switches, and Battery compartment.]

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.