MICROCHIP SM48DB Silicon Sculptor 4 Conformance Test Instruction Manual

Instruction Manual for MICROCHIP models including: SM48D, SM48DB, SM48DB Silicon Sculptor 4 Conformance Test, Silicon Sculptor 4 Conformance Test, Sculptor 4 Conformance Test, Conformance Test, Test

Silicon Sculptor 4 Conformance Test Instructions

Microchip Technology Inc.

Silicon Sculptor 4 Conformance Test ...

Silicon Sculptor 4 Conformance Test Instructions

File Info : application/pdf, 12 Pages, 749.67KB

Silicon Sculptor 4 Conformance Test Instructions

Silicon Sculptor 4 Conformance Test Instructions
Introduction
This document provides detailed instructions on the Silicon Sculptor 4 (SS4) conformance test.
Required Hardware
The following is the list of required hardware for the conformance test: · SS4 to be tested · SM48D or SM48DB socket module · Voltmeter · Oscilloscope The following figure shows the location of pins 1 and 48 of the SM48D/SM48DB socket module. These pins are used to perform the actual voltage and waveform measurements. Figure 1. SM48D/SM48DB Socket Module

Manual
© 2023 Microchip Technology Inc. and its subsidiaries

DS50003497A - 1

Setup Instructions
To setup the unit, perform the following steps: 1. Place SM48D or SM48DB onto the SS4 programmer as shown in the following figure.
Figure 2. SM48D/SM48DB Socket Module Placed on SS4 Programmer

2. Connect the SS4 programmer to the PC using a USB cable.
3. Connect the power supply to the programmer and power outlet. Note:Ensure that the power for the programmer is still turned off.
4. Install the latest version of the SculptW software on your computer, if not installed.
5. Launch the SculptW software. The programmer must be powered after this step. Ensure that the green LED illuminates after powering up the system. If the programmer fails to turn on, then close the software, check the USB and power connections, and attempt to power up the programmer again.

Manual
© 2023 Microchip Technology Inc. and its subsidiaries

DS50003497A - 2

The following figure shows SculptW software. Figure 3. SculptW Sofware

Test Instructions
To start the test, perform the following steps: 1. Click the Device menu, then in the Look for box, type BP as shown in the following figure. 2. Click BP Microsystems SS4 Certificate of Conformance Test, and then click Select.

Manual
© 2023 Microchip Technology Inc. and its subsidiaries

DS50003497A - 3

Figure 4. Select Device

3. The following window then appears explaining how to run the test. Press Enter to close this window. Figure 5. Device Notes
4. Click Execute to start the test.
High Voltage Test
To conduct the high voltage test, perform the following steps: 1. Connect the voltmeter probes to pins 1 and 48.

Manual
© 2023 Microchip Technology Inc. and its subsidiaries

DS50003497A - 4

Figure 6. High Voltage Test
2. Measure the voltage of the pin 1 as shown in the following figure. Check if the voltage reading is within the specified range. If the voltage readings fall outside of the specified range, it indicates that the programmer is out of calibration and requires service. The following figure shows voltage measurement of the pin 1. Figure 7. Voltage Measurement of the Pin 1

3. Press Start to move on to the next test.
Low Voltage Test
To conduct the low voltage test, perform the following steps: 1. Measure the voltage of the pin 1 as shown in the following figure. Check if the voltage reading is within the
specified range. If the voltage readings fall outside of the specified range, it indicates that the programmer is out of calibration and requires service.

Manual
© 2023 Microchip Technology Inc. and its subsidiaries

DS50003497A - 5

Figure 8. Low Voltage Test Figure 9. Voltage Measurement of the Pin 1

2. Press Start to move on to the next test.
Low Frequency Test
To conduct the low frequency test, perform the following steps: 1. Connect the scope probe to pin 1 and ground to pin 48.
Manual
© 2023 Microchip Technology Inc. and its subsidiaries

DS50003497A - 6

Figure 10. Low Frequency Test
2. Set the probe voltage of the oscilloscope to 2 V/Div. 3. Adjust the timing to see an entire wave period as shown in the following figure.
Figure 11. Expected Result of Low Frequency Test

4. Measure the frequency of one period of the wave form. Check if the frequency reading is within the specified range. If the measured frequency falls outside of the specified range, it indicates that the programmer is out of calibration and requires service.
5. Press Start to move on to the next test.
Pulse Width Test
To conduct the pulse width test, perform the following steps:
1. Set the trigger of the oscilloscope to capture the signal on the rising edge of the signal.

Manual
© 2023 Microchip Technology Inc. and its subsidiaries

DS50003497A - 7

Figure 12. Pulse Width Test
2. Measure the pulse width. Check if the pulse width reading is within the specified range. If the measured pulse width falls outside of the specified range, it indicates that the programmer is out of calibration and requires service. The following figure shows the expected result of pulse width test. Figure 13. Expected Result of Pulse Width Test

3. Press Start to terminate the test.

Manual
© 2023 Microchip Technology Inc. and its subsidiaries

DS50003497A - 8

Microchip Information
The Microchip Website
Microchip provides online support via our website at www.microchip.com/. This website is used to make files and information easily available to customers. Some of the content available includes:
· Product Support Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software
· General Technical Support Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip design partner program member listing
· Business of Microchip Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
Product Change Notification Service
Microchip's product change notification service helps keep customers current on Microchip products. Subscribers will receive email notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest.
To register, go to www.microchip.com/pcn and follow the registration instructions.
Customer Support
Users of Microchip products can receive assistance through several channels:
· Distributor or Representative
· Local Sales Office
· Embedded Solutions Engineer (ESE)
· Technical Support
Customers should contact their distributor, representative or ESE for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in this document.
Technical support is available through the website at: www.microchip.com/support
Microchip Devices Code Protection Feature
Note the following details of the code protection feature on Microchip products:
· Microchip products meet the specifications contained in their particular Microchip Data Sheet.
· Microchip believes that its family of products is secure when used in the intended manner, within operating specifications, and under normal conditions.
· Microchip values and aggressively protects its intellectual property rights. Attempts to breach the code protection features of Microchip product is strictly prohibited and may violate the Digital Millennium Copyright Act.
· Neither Microchip nor any other semiconductor manufacturer can guarantee the security of its code. Code protection does not mean that we are guaranteeing the product is "unbreakable". Code protection is constantly evolving. Microchip is committed to continuously improving the code protection features of our products.
Legal Notice
This publication and the information herein may be used only with Microchip products, including to design, test, and integrate Microchip products with your application. Use of this information in any other manner violates these terms. Information regarding device applications is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure

DS50003497A - 9

that your application meets with your specifications. Contact your local Microchip sales office for additional support or, obtain additional support at www.microchip.com/en-us/support/design-help/ client-support-services.
THIS INFORMATION IS PROVIDED BY MICROCHIP "AS IS". MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, OR WARRANTIES RELATED TO ITS CONDITION, QUALITY, OR PERFORMANCE.
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL LOSS, DAMAGE, COST, OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE INFORMATION OR ITS USE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THE INFORMATION OR ITS USE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THE INFORMATION.
Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, CryptoMemory, CryptoRF, dsPIC, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch, MediaLB, megaAVR, Microsemi, Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, PolarFire, Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
AgileSwitch, APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, Flashtec, Hyper Speed Control, HyperLight Load, Libero, motorBench, mTouch, Powermite 3, Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet- Wire, SmartFusion, SyncWorld, Temux, TimeCesium, TimeHub, TimePictra, TimeProvider, TrueTime, and ZL are registered trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, Augmented Switching, BlueSky, BodyCom, Clockstudio, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, Espresso T1S, EtherGREEN, GridTime, IdealBridge, In-Circuit Serial Programming, ICSP, INICnet, Intelligent Paralleling, IntelliMOS, Inter-Chip Connectivity, JitterBlocker, Knob-on-Display, KoD, maxCrypto, maxView, memBrain, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, RTAX, RTG4, SAMICE, Serial Quad I/O, simpleMAP, SimpliPHY, SmartBuffer, SmartHLS, SMART-I.S., storClad, SQI, SuperSwitcher, SuperSwitcher II, Switchtec, SynchroPHY, Total Endurance, Trusted Time, TSHARC, USBCheck, VariSense, VectorBlox, VeriPHY, ViewSpan, WiperLock, XpressConnect, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage Technology, and Symmcom are registered trademarks of Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their respective companies.

DS50003497A - 10

© 2023, Microchip Technology Incorporated and its subsidiaries. All Rights Reserved.
ISBN: 978-1-6683-2865-1
Quality Management System
For information regarding Microchip's Quality Management Systems, please visit www.microchip.com/quality.

DS50003497A - 11

Worldwide Sales and Service

AMERICAS
Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: www.microchip.com/support Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078

ASIA/PACIFIC
Australia - Sydney Tel: 61-2-9868-6733 China - Beijing Tel: 86-10-8569-7000 China - Chengdu Tel: 86-28-8665-5511 China - Chongqing Tel: 86-23-8980-9588 China - Dongguan Tel: 86-769-8702-9880 China - Guangzhou Tel: 86-20-8755-8029 China - Hangzhou Tel: 86-571-8792-8115 China - Hong Kong SAR Tel: 852-2943-5100 China - Nanjing Tel: 86-25-8473-2460 China - Qingdao Tel: 86-532-8502-7355 China - Shanghai Tel: 86-21-3326-8000 China - Shenyang Tel: 86-24-2334-2829 China - Shenzhen Tel: 86-755-8864-2200 China - Suzhou Tel: 86-186-6233-1526 China - Wuhan Tel: 86-27-5980-5300 China - Xian Tel: 86-29-8833-7252 China - Xiamen Tel: 86-592-2388138 China - Zhuhai Tel: 86-756-3210040

ASIA/PACIFIC
India - Bangalore Tel: 91-80-3090-4444 India - New Delhi Tel: 91-11-4160-8631 India - Pune Tel: 91-20-4121-0141 Japan - Osaka Tel: 81-6-6152-7160 Japan - Tokyo Tel: 81-3-6880- 3770 Korea - Daegu Tel: 82-53-744-4301 Korea - Seoul Tel: 82-2-554-7200 Malaysia - Kuala Lumpur Tel: 60-3-7651-7906 Malaysia - Penang Tel: 60-4-227-8870 Philippines - Manila Tel: 63-2-634-9065 Singapore Tel: 65-6334-8870 Taiwan - Hsin Chu Tel: 886-3-577-8366 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Thailand - Bangkok Tel: 66-2-694-1351 Vietnam - Ho Chi Minh Tel: 84-28-5448-2100

EUROPE
Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4485-5910 Fax: 45-4485-2829 Finland - Espoo Tel: 358-9-4520-820 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-72400 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Rosenheim Tel: 49-8031-354-560 Israel - Ra'anana Tel: 972-9-744-7705 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-72884388 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820

DS50003497A - 12

References

Antenna House PDF Output Library 7.0.1621