Outdoor Tech Chips Ultra 2.0 True Wireless Helmet Audio

What's Inside

• Left Ear Piece
• Right Ear Piece
• Charging Case: A case designed for charging and storing the ear pieces, featuring fast charging with a USB-C cable.
• USB-C charging cable
• Instruction manual
• One ODT sticker

Anatomy

• A. Left ear button: Button on the left earpiece.
• B. Right ear button: Button on the right earpiece.
• C. LED light: Indicator light on the earpieces and charging case.
• D. Microphone: Built-in microphone ? for calls.
• E. Hi-Fi Speakers: High-fidelity speakers ? for audio output.

Functions

Left Earpiece Functions

Power On: Long press for 3 seconds.

Power Off: Press and hold for 4 seconds.

Volume Up: Short press once.

Volume Down: Short press twice.

Right Earpiece Functions

Power On: Long press for 3 seconds.

Power Off: Press and hold for 4 seconds.

Answer/Hang Up Call: Short press once.

Reject Call: Long press for 2 seconds.

Play/Pause Music: Short press once.

Skip Forward: Short press twice.

Skip Backward: Short press three times.

Siri/Voice Activation: Long press for 1 second.

Note: Resetting Chips Ultra / Clearing BT Memory instructions are provided in a separate paper insert.

Charging

Charging the Case

Charge the case to power your Chips® Ultra 2.0 on the go. It supports fast charging via USB-C. When plugged in, the front indicator light turns RED (CHARGING) and GREEN when fully charged. Case total charging time: 1.5 hours.

Charging the Chips

Charge your Chips® Ultra 2.0 by placing them in the charging case. Gently plug the three holes on the side of each chip into the corresponding prongs in the case, ensuring Left goes into Left and Right into Right. The LED lights on the chips will turn RED (CHARGING) and turn off when fully charged. Chips® Ultra 2.0 total charging time: About 2 hours.

Pairing

Featuring an advanced chip set for better connection with Bluetooth 5.0 ?.

1. Power on the Right earpiece (long press 3 seconds). Voice prompt: "power on >> battery level >> pairing".
2. Power on the Left earpiece (long press 3 seconds). Voice prompt: "power on >> connected".
3. On your phone's Bluetooth settings, choose "ODT Chips Ultra 2.0".
4. Voice prompt: "device connected".

Installing in Your Helmet

1. Drop the CHIPS® Ultra 2.0 into the slots inside your helmet liner.
2. Enjoy your audio experience while engaging in activities like skiing and snowboarding.

Specifications

Chips Ultra 2.0

• Bluetooth version: Bluetooth 5.0+ EDR
• Bluetooth profiles: A2DP, AVRCP, HSP, HFP
• Driver units: 40mm Neodymium magnet
• Frequency Response: 20~20,000 Hz
• Impedance: 32 + 32 ohms
• Sensitivity (1kHz): 110 dB
• Range: Up to 10m/33ft
• Microphone: Built-in microphone ?
• Battery: 3.7V, 250 mAh
• Chips Charging time: About 2 hours
• Play / Talk time: Up to 14 hours

Charging Case

• Charging time: 1.5 hours (DC 5V 2A)
• Battery: 3.7V 2000 mAh

Care & Maintenance

• Keep away from direct sunlight or hot places to prevent damage to electronics, battery, or plastic parts.
• Do not attempt to disassemble the CHIPS® Ultra 2.0.
• Avoid dropping the product onto hard surfaces, as internal circuits may be damaged.
• Do not use harsh chemical products or detergents for cleaning.
• Do not scratch the surface with sharp objects.

Compliance & Safety

Safety Warning: For safety reasons, some laws prohibit the use of headsets when operating vehicles. Use Chips only for off-highway activities. Do not use Chips at excessive volumes, as it may cause permanent hearing damage. ⚠️

FCC & IC Compliance: This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, try correcting it by reorienting the antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a dealer/technician.

FCC & IC Radiation Exposure Statement: This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. (Déclaration d'IC sur l'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux radiations définies par le Canada pour des environnements non contrôlés. Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur.)

Connect With Us

Follow us:

• Facebook: facebook.com/outdoortechnology
• Twitter & Instagram: @outdoortech

Contact: For questions, comments, or feedback, email info@outdoortech.com.

Website: outdoortech.com