VEHICLE STATUS INFORMATION AND INDICATORS

Instrument cluster

Gauges and meters (with 7-inch display)

Meter display

Locations of gauges and meters

The display of the speedometer can be selected from two types, analog or digital. (Click Here)

Analog speedometer

The units used on the meter and display may differ depending on the target region.

The display shows various indicators and gauges:

• A Hybrid System Indicator: Displays the Hybrid System Indicator. (Click Here)
• B Speedometer: Displays the vehicle speed.
• C Clock: Displays the current time. (Click Here)
• D Fuel gauge: Displays the quantity of fuel remaining in the tank.
• E Engine coolant temperature gauge: Displays the engine coolant temperature.
• F Odometer, trip meter and instrument cluster light control display:
  • Odometer: Displays the total distance the vehicle has been driven.
  • Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters "A" and "B" can be used to record and display different distances independently.
  • Instrument cluster light control: Displays the brightness of the instrument cluster lights, which can be adjusted.
• G Outside temperature: Displays the ambient outside temperature. (Click Here)
• H Multi-information display: Presents the driver with a variety of driving-related data. (Click Here)
• I Shift position and shift range indicator: Displays the selected shift position or selected shift range. (Click Here)

The meters and display illuminate when the power switch is in ON.

Hybrid System Indicator

The Hybrid System Indicator visually represents the status of the hybrid system. It includes the following areas:

• A READY OFF area: Shows that the hybrid system is not operating.
• B Charge area: Shows regeneration status. Regenerated energy will be used to charge the hybrid battery (traction battery).
• C Hybrid Eco area: Shows that gasoline engine power is not being used very often. The gasoline engine will automatically stop and restart under various conditions.
• D Eco area: Shows that the vehicle is being driven in an Eco-friendly manner. By keeping the indicator needle within the Eco area, more Eco-friendly driving can be achieved.
• E Power area: Shows that an Eco-friendly driving range is being exceeded, typically during full power driving.

* "Regeneration" refers to the conversion of energy created by the movement of the vehicle into electrical energy.

The Hybrid System Indicator does not operate in the following situations:

• The "READY" indicator is not illuminated.
• The shift lever is in a range other than D or S.

Outside temperature display

The correct outside temperature may not be displayed, or the display may take longer than normal to change, in the following situations:

• When stopped, or driving at low speeds (less than 20 km/h [12 mph]).
• When the outside temperature has changed suddenly (e.g., at the entrance/exit of a garage, tunnel, etc.).

If "--" or "E" is displayed, the system may be malfunctioning. Take your vehicle to your Toyota dealer.

The display shows the outside temperature within the range of -40°C (-40°F) to 60°C (140°F).

When the outside temperature is approximately 3°C (37°F) or lower, the indicator [Temperature Warning Icon] will flash for approximately 10 seconds, then stay on.

Liquid crystal display

WARNING: Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the display monitor may respond slowly, and display changes may be delayed.

Using the "ODO TRIP" switch

The "ODO TRIP" switch is used to cycle through the odometer, trip meter A, trip meter B, and adjust the brightness of the instrument cluster lights.

• When the trip meter is displayed, pressing and holding the switch will reset the trip meter.
• When the instrument cluster light control display is shown, pressing and holding the switch will adjust the brightness of the instrument cluster lights.

Instrument cluster brightness adjustment

The instrument cluster brightness levels can be adjusted individually for when the tail lights are on and off. However, when the surroundings are bright (daytime, etc.), turning on the tail lights will not change the instrument cluster brightness.

Adjusting the clock

The clock can be adjusted on either the multi-information display or the multimedia system.

By displaying the "Clock :00" screen from the multi-information display, you can change the following settings related to the clock:

• Resetting the minutes display.
• Changing the clock between 12-hour display and 24-hour display.
• Adjusting the time.

To reset the minutes display

1. Press the [Left Arrow Button] or [Right Arrow Button] of the meter control switches on the steering wheel and select the desired screen.
2. Press the [Up Arrow Button] or [Down Arrow Button] of the meter control switches on the steering wheel and select "Clock :00".
3. On the "Clock :00" screen, press the [Select Button] of the meter control switches to set "Minutes" to 00.

Minutes from 0 to 29 are rounded down (e.g., from 1:00 to 1:29 are displayed as 1:00). Minutes from 30 to 59 are rounded up (e.g., from 1:30 to 1:59 are displayed as 2:00).

To adjust the time

1. Press the [Left Arrow Button] or [Right Arrow Button] of the meter control switches on the steering wheel and select the desired screen.
2. Press the [Up Arrow Button] or [Down Arrow Button] of the meter control switches on the steering wheel and select "Clock :00".
3. On the "Clock :00" screen, press and hold the [Select Button] of the meter control switches.
4. Select "12H/24H", "Time", or "Minutes" by operating the [Left Arrow Button] or [Right Arrow Button] of the meter control switches.
5. Press the [Up Arrow Button] or [Down Arrow Button] of the meter control switches to change the display contents. When the setting is completed, press the [Return Button] to return to the previous screen.

© Toyota Kirloskar Motor Pvt Ltd. 2022

For more details, visit: Toyota Bharat Official Manual