Magnadyne RV2458 Router Quickstart Guide

RV2458 Router Overview

The Magnadyne RV2458 is a Wi-Fi extender that can be used with either the RV2400 (Wi-Fi Only) or the RV2402 (Wi-Fi / LTE) extender.

RV2400 Extender (Wi-Fi Only)

This is a diagram showing the RV2400 Extender, which is Wi-Fi only.

RV2402 Extender (Wi-Fi / LTE)

This is a diagram showing the RV2402 Extender, which supports both Wi-Fi and LTE connectivity.

How to Activate your 4G LTE Data Plan

If you have purchased the WF-CON-LTE system or upgraded from the Wi-Fi only RV2400 to the Wi-Fi / LTE enabled RV2402, you will need to activate a data plan to take advantage of the LTE benefits.

To begin LTE Activation, the system must be installed and operational. Follow Steps 1-6 in this manual. At Step 7, select "LTE" and proceed to Step 15. You will then be presented with the ICCID and IMEI numbers required for your Data Plan Activation. Record these numbers in the provided space.

The RV2402 comes with an AT&T SIM preinstalled for easy activation at www.att.com/RV-Link. For activation difficulties, consult the FAQ section or use the chat function on the order page for technical support.

Once logged into the RV-Link page of the AT&T portal, you will see the latest high-speed data plans and an easy activation process. Follow the on-screen instructions.

IMPORTANT: Access to the internet is required for LTE Data Plan Activation.

ICCID #: [Input Field]

IMEI #: [Input Field]

AT&T and its marks are trademarks of AT&T Intellectual Property. Other marks are the property of their respective owners. Information is subject to change. AT&T products and services are provided by subsidiaries and affiliates of AT&T Inc.

RV2458 Software Quickstart Guide

1. Step 1: Power On

   Press the power button on the RV2458 to power up the Router (approximately 2 minutes).

   • Power: Blue & Solid
   • Extender: Blue & Flashing
   • Router: Blue & Flashing

2. Step 2: Connect to RV2458 Wi-Fi

   Go to your device's Wi-Fi settings (phone, tablet, laptop). Ensure Wi-Fi is turned on and select the RV2458-2.4G Network.

   NOTE: If your phone is being used as a hotspot, a second device will be required for configuration.

3. Step 3: Enter Wi-Fi Password

   In the password field, type RV2458WiFi and click the Join button. This password is case-sensitive.

4. Step 4: Confirm Connection

   Wait for your device to connect to the RV2458-2.4G Network.

5. Step 5: Access Router Interface

   Open your web browser and enter the address 192.168.10.1. Click Go or press Enter.

6. Step 6: Login to Router

   On the login screen, enter the password admin (case-sensitive) and click the Login button.

7. Step 7: Select Connection Type

   If WiFi is selected, proceed to Step 8. If LTE is selected, proceed to Step 15.

8. Step 8: Wait for Scanning

   Wait for the scanning countdown to complete (approximately 10 seconds).

9. Step 9: Select Wi-Fi Network

   The Available Wi-Fi List screen will appear. Click on the desired Wi-Fi Network to connect the Router. If the scroll bar is not visible on a Mac computer, move your cursor up and down over the SSID names.

10. Step 10: Connect to Wi-Fi Host

    A password pop-up window will appear. Enter the password for the chosen Wi-Fi host and click Connect. If you were previously connected, the password may refresh automatically. If the unit does not connect, ensure the 2-minute boot cycle is complete. Restart from Step 1 if necessary.

11. Step 11: Connecting Countdown

    The connecting countdown page will complete, and the login screen will appear. You must wait 2 minutes after hitting the connect button for the unit to establish its connection. A 45-second wait may result in a failed connection.

12. Step 12: Login with Admin Credentials

    Enter the password admin (case-sensitive) and click the Login button. If successful, proceed to Step 13.

13. Step 13: Handle Connection Failure

    If the password was entered incorrectly, a pop-up window will appear stating the connection failed. Click OK. The unit will return to Step 7 to scan again. Double-check the network password.

14. Step 14: Wi-Fi Connection Successful

    You have successfully connected to the Wi-Fi Host. If Wi-Fi was selected, return to Step 9. If LTE was selected, proceed to Step 15.

15. Step 15: Start LTE Connection

    If using the recommended AT&T Preferred Plan, click the Start LTE button. For other carriers, ensure the correct APN, Username, and Password are entered as required.

    ICCID: [Value], IMEI: [Value]

    Protocol: PPP

    APN setting: Manual

    APN: Broadband

    Username: [Input]

    Password: [Input]

16. Step 16: Establishing LTE Connection

    The LTE module is starting and establishing a connection with the LTE carrier. Please wait 115 seconds. Do not turn off or reboot the device during this time.

17. Step 17: LTE Started Successfully

    LTE has been successfully started. Reconnecting, please wait.

18. Step 18: Login After LTE Start

    Enter the password admin (case-sensitive) and click the Login button. If successful, proceed to Step 13.

19. Step 19: LTE Connection Successful

    You have a successful connection to the LTE carrier. To turn OFF LTE, click the LTE Off button and proceed to Step 20.

    Status LTE:

    RV2400 (Outside) Information
    Connection to LTE	Connected
    Carrier	AT&T
    Network	LTE
    Link Strength	-88 dbm
    RV2458 (Inside) Information
    RV2400 to RV2458 Pairing	Paired
    Connected Users	1
    Date & Time	12-02-19/15:45:16

    LTE Off

20. Step 20: Turning OFF LTE

    LTE is being turned OFF. Please wait 120 seconds. Do not turn off or reboot the device during this time.

21. Step 21: LTE Stopped Successfully

    Once Step 20 is complete, you will receive this notice and be returned to Step 7.

Notes:

[Blank Lined Space for Notes]