Magnadyne RV6200S Operation and Installation Manual

Introduction

Please take the time to read all of the information in this manual. Familiarity with operation and installation procedures will help you obtain the best possible performance from your new AM/FM Stereo Multi-Media Receiver.

WARNING! To prevent fire or electrical shock hazard, do not expose this product to moisture. No user-serviceable parts inside. Refer servicing to qualified personnel.

Getting Started

• 1. Power On/Off, Mute: Short press to turn the unit on or to mute audio. Long press to power off.
• 2. Volume +: Short press to increase volume. Long press to quickly increase volume.
• 3. Seek Up [seek-forward]: Press to tune the radio to a higher frequency or to navigate to the next track in USB, Disc, or Bluetooth mode.
• 4. A Speaker Selection: Short press to control A speakers volume. Long press to turn all speakers on/off.
• 5. B Speaker Selection: Short press to control B speakers volume. Long press to turn all speakers on/off.
• 6. C Speaker Selection: Short press to control C speakers volume. Long press to turn all speakers on/off.
• 7. SLEEP: Short press for sleep on/off. Long press for sleep time setting.
• 8. ALARM: Short press to turn alarm on/off. Long press for alarm time setting.
• 9. DIM: Short press for screen dimmer adjustment between high/mid/low/off.
• 10. Disc Slot: Insert a disc with the label facing up to play.
• 11. AM/FM: Short press to select radio bands: FM1, FM2, FM3 (MHz), AM1, AM2 (KHz). Long press to auto store stations.
• 12. EJECT: Short press to eject disc.
• 13. DISC: Short press to switch to disc mode and song search while in disc mode.
• 14. AUX: Short press for AUX 1, long press for AUX 2.
• 15. USB: Short press to switch to USB mode and song search while in USB mode.
• 16. BT: Short press to switch to Bluetooth mode. Long press to unpair a connected device.
• 17. 6 / DIR+: Short press to recall radio preset or search ahead in DISC/USB mode. Long press to memorize a radio station.
• 18. Headphone Socket: Accepts 3.5mm stereo headphone jacks.
• 19. 5 / DIR-: Short press to recall radio preset or search backwards in DISC/USB mode. Long press to memorize a radio station.
• 20. USB Charging: Quick charge USB port. (Does not play music).
• 21. 4 / RDM: Short press to recall radio preset or to turn Random ON/OFF in DISC/USB mode. Long press to memorize a radio station.
• 22. Reset: Press to reset the unit to default settings.
• 23. 3 / RPT: Short press to recall radio preset or to toggle between Repeat One / All in DISC/USB mode. Long press to memorize a radio station.
• 24. USB Music: Music media USB port.
• 25. 2 / INT: Short press to recall radio preset or to turn Intro ON/OFF in DISC/USB mode. Long press to memorize a radio station.
• 26. Audio Input Jack: Plug in a device via the 3.5mm audio input plug.
• 27. Play [play-symbol] / Pause [pause-symbol]: Short press to recall radio preset. Long press to memorize a radio station. Press to pause in DISC/USB/BT modes, press again to restore playback. Long press to show software version in AUX mode.
• 28. DISP: Short press to toggle between info and clock display. Long press to enter clock settings.
• 29. Volume - [volume-down]: Short press to decrease volume. Long press to quickly decrease volume.
• 30. EQ: Short press to toggle between EQ presets: FLAT, POP, ROCK, CLASS, or EQ OFF. Long press to turn LOUD ON/OFF.
• 31. Seek Down [seek-backward]: Press to tune the radio to a lower frequency or to navigate to the previous track in USB, Disc, or Bluetooth mode.
• 32. SEL: Short press to select sound controls: BAS-TRE-BAL-EQ-LOUD. Long press for BEEP ON/OFF, Clock 12/24, P-Vol, CT Indep/Sync, Area USA/EUR, Lo/DX, ST/Mo.
• 33. IR Sensor: Remote control sensor.

RV6200S General Operations

Power On/Off

Press the [power-symbol] to turn the unit On. When the unit is on, a short press will mute all audio. Press and hold to turn the unit off.

Selecting a Play Source

Press the touch screen panel on the unit to directly select AM/FM, DISC, AUX, USB, or BLUETOOTH play sources.

Dimming the Display

Short press the DIM button to select from the 4 levels of brightness for the display area: DIM LOW, DIM MID, DIM HIGH, off.

Display Selection

Press the DISP button to display the clock. Press again to return to the previous display. Press and hold to perform clock setting functions (See "Setting the Clock" for more details).

Selecting Speaker Sets

Note: See Sound Controls for detailed volume and mute control operations.

Setting the Clock

1. Press the DISP button until the clock appears in the display.
2. Press and hold the DISP button until the Hours number starts flashing.
3. Press the [plus] or [minus] buttons to set the desired hour displayed on the unit's screen. Note: When setting the clock, make sure to select the correct AM or PM.
4. Press the DISP button and the Minute indicators will start flashing.
5. Press the [plus] or [minus] buttons to set the desired minutes displayed on the unit's screen. When finished, press the DISP button and the time will be set.

Setting the Alarm Timer

1. Short press the ALARM button to toggle between ALARM ON or ALARM OFF.
2. To set the alarm time, press and hold the ALARM button. The hour will flash and can be adjusted using the [plus] and [minus] buttons. To adjust the minutes, press and hold the ALARM button until the minutes flash, then adjust using the [plus] and [minus] buttons.
3. With the alarm set, "ALARM" will appear in the display. When the set alarm time is reached, a beep sound will be heard and will continue until any radio button is pushed.
4. When the alarm time is set and the unit is off, the unit will automatically turn on to sound the alarm beep when the scheduled time is reached.

Setting the Sleep Timer

1. Press the SLEEP button to toggle between SLEEP ON and SLEEP OFF.
2. With SLEEP ON selected, press the [plus] or [minus] buttons to set the desired sleep time up to 60 minutes.
3. Wait 5 seconds and the display will return to normal operation, showing "SLEEP".
4. After the designated sleep timer has expired, the unit will turn off automatically.

Cancelling the Sleep Timer

1. Press the SLEEP button; "SLEEP OFF" will appear in the display.
2. Wait 5 seconds and the display will return to normal operation.

Headphone Operations

Insert headphones into the 3.5mm headphone jack located on the front panel. The unit's speakers will automatically be muted.

BEEP ON/OFF

To turn the unit's audible beep on or off, short press the SEL button until "BEEP ON" or "BEEP OFF" appears in the display. Use the VOL [plus]/[minus] buttons to make your selection.

CLOCK 12/24

To set the unit's clock to either a 12 or 24-hour format, press the SEL button until "CLOCK 12" or "CLOCK 24" appears in the display. Use the VOL [plus]/[minus] buttons to make your selection.

General Reset

To reset the unit, press the reset button located on the front of the radio using the tip of a ballpoint pen. This is a general logic reset for button function, display, and Bluetooth issues. This reset may not clear all issues.

Hard Reset

This reset will restore all functions to factory defaults, wiping all programming, settings, and memory functions.

1. Turn the radio On.
2. Select the AUX IN 1 input.
3. Press and hold the [seek-forward] button until "RESET" is displayed (approx. 5 seconds), then release it. The radio will turn off.
4. Push the power button to turn the radio back on. Check if the issue is corrected.

Note: All memory settings (clock, station memory, tone settings, etc.) will need to be re-input.

Sound Controls

SPK A/B/C Volume/Mute Control Operation

1. The volume of each speaker set can be adjusted independently. Short press the A, B, or C button to select the speakers the volume control will affect (the LCD displays the "SPK A", "SPK B", or "SPK C" icon). Pressing the VOL [plus]/[minus] button will change the volume of the selected speakers.
2. To control the volume of all speaker sets simultaneously, press and hold the A, B, or C button for 2 seconds (the LCD will display "SPK A", "SPK B", and "SPK C" icons together).
3. To mute the sound of all speakers, briefly press the power button. All speakers will be muted. Press the power button again to resume the previous volume level.

Note 1: To bring all speaker outputs to the same volume level, press and hold the A, B, or C button for 2 seconds (the LCD will display the "SPK A", "SPK B", and "SPK C" icons together), then press and hold the volume [-] until each level reaches zero. From that point, press the volume [+] button, and all speakers will rise in volume equally.

Note 2: The output loudness of the subwoofer can only be controlled by adjusting the volume of "SPK A". Selecting SPK B or C will not adjust the subwoofer's loudness.

Bass, Treble and Balance Control

Select the desired sound mode to adjust by short pressing the SEL button. The modes will be displayed in the following order: Bass, Treble, Balance, EQ, Loud.

Bass

Select the Bass mode by short pressing the SEL button. Adjust the Bass level by pressing the VOL [plus]/[minus] buttons. After 5 seconds, control reverts back to volume control.

Treble

Select the Treble mode by pressing the SEL button. Adjust the Treble level by pressing the VOL [plus]/[minus] buttons. After 5 seconds, control reverts back to volume control.

Balance

Select the Balance mode by pressing the SEL button. Adjust the Balance by pressing the VOL [plus]/[minus] buttons.

• 0 = Equal sound Right and Left
• R 7 = Right speaker only
• L 7 = Left speaker only

After 5 seconds, control reverts back to volume control.

Equalizer (EQ)

Select the EQ mode by pressing the SEL button. Adjust the EQ by pressing the VOL [plus]/[minus] buttons to choose between the preset settings: Classic, Rock, Pop, Flat, or EQ OFF, as indicated in the display. After 5 seconds, control reverts back to volume control.

Loud

To boost high and low tones at low volume levels, press the SEL button until "LOUD ON" appears in the display. To deselect, press either VOL [plus]/[minus] buttons, and "LOUD OFF" will appear in the display.

Radio Operations

Radio Settings

Press and hold the SEL button to access radio settings, then short press SEL to select between the listed setting options. Press the [plus] and [minus] buttons to make your selections (ON/OFF, up or down levels):

• P-VOL-: Radio's default volume level.
• AREA-: USA, EUR.
• DX/LOC-: Distant / Local. Affects seek and scan sensitivity and ability to lock into either distant weak signal stations or local strong signal stations.
• STEREO/MONO-: Multiple separated stereo sound or single channel sound.
• CT SYNC / INDEX:
  • CT SYNC: When receiving an RDS station, the clock will be synchronized to the station's time.
  • CT INDEP: The clock will run independently, not synchronized to the station's time. This is the default setting.

Receive a Radio Station

• Press the AM/FM button to select RADIO mode.
• Press the AM/FM button to select between AM 1 or 2 (KHz) or FM 1, 2, or 3 (MHz).
• Short presses of [seek-backward] or [seek-forward] will seek to the nearest reachable radio frequency. Long presses will allow you to manually find a station.

Manually Storing and Recalling Stations

• Tune into the desired station and press and hold one of the preset buttons (1-6) for 2 seconds. The current station will be stored into that number button's memory and can then be recalled with a short press of that button.

Auto Storing Stations

• Press and hold the AM/FM button for 2 seconds to auto scan and store AM 1, 2 and FM 1, 2, and 3 stations into numeric buttons 1-6.

Note: When the MHz (FM) band is selected, the 18 strongest stations will be stored. When KHz (AM) band is selected, the 12 strongest stations will be stored.

USB Operation

Selecting USB Audio Play Source

When a USB device is inserted, the unit automatically switches to USB mode and plays files from the inserted device. If the USB device remains inserted, other audio source buttons can be pressed to navigate to other modes, or you can return to USB mode by pressing the USB button.

USB File Selection

• Short press the [previous-track] or [next-track] button to skip to the previous or next audio track. File information will automatically appear in the display.
• Press and hold the [previous-track] or [next-track] button to fast forward or reverse through a selected track.

DIR+ / DIR-

Press the DIR+ / DIR- button to play the next / previous folder from the USB device.

Pausing the Audio

Press the [play-pause] button to pause the audio file. Press again to resume playback.

Intro

Press the INT button to play the first 10 seconds of each file. Press again to stop this function.

Repeat

Press the RPT button to repeat a single track or to repeat an entire playlist.

Random

Press the RDM button to play files from a playlist in random order.

Specific Track Number

Press the USB button to display "NUM 0000". Press the VOL [plus]/[minus] buttons or directly enter the desired track number.

To enter a specific track number using radio buttons, press:

• Buttons 1-6
• EQ button = 7
• [seek-backward] button = 8
• [seek-forward] button = 9
• DISP button = 0

AUX 1 / AUX 2 Operation

Selecting the Audio Source

Note: The RV6200S does not control AUX connected devices; it only allows the audio to be played through the system.

Front Audio Input

Insert the 3.5mm jack from the audio device into the AUX input socket on the front of the unit. Press the AUX button until "AUX 1" appears in the display. Refer to the audio device's owner's manual for proper operation.

Rear Audio Input

To select the rear RCA connected audio play source, press and hold the AUX button until "AUX 2" appears in the display. Refer to the audio device's owner's manual for proper operation.

Note: The volume setting of the connected audio device affects the overall loudness of the RV6200S.

Subwoofer

The RCA Subwoofer output connection is located on the back of the radio chassis and is identified by the green colored insert on the connector. This output provides a low output level signal filtered at 220Hz. It requires an additional amplifier and subwoofer speaker, or an amplified subwoofer. This output will not power a speaker directly.

HDMI Arc Function

The radio's HDMI output supports the ARC (Audio Return Channel) feature, allowing audio from a TV set to be played through the radio without additional cables. ARC is a relatively new feature, and not all TV sets support it. In such cases, the HDMI connection from the radio will only deliver a video signal to your TV set.

If your TV's HDMI input connection supports ARC, it will be identified as HDMI (ARC). Some TVs with HDMI (ARC) input may require activation of the ARC feature through the TV's setting menu. Consult your TV user manual.

1. To play sound from the TV through the radio speakers, select "Disk" on the radio (eject any disc inside the radio), and the display will read "HDMI ARC". Wait a few seconds for the system to handshake; the TV sound will then play through the radio speakers. The volume level of the radio speakers is controlled at the radio.
2. If you change the source on the radio (e.g., switch back to FM radio), the TV sound will stop, and the alternate source will play through the radio speakers.
3. If you want to play the radio's DVD sound only through the TV speakers, you can lower the sound at the radio and turn up the sound on the TV speakers.

Bluetooth Operation

Pairing Bluetooth Devices

1. Open the Bluetooth settings program on your mobile device and activate the Bluetooth feature.
2. From your mobile device, scan for available devices.
3. Select "LINEAR SERIES" to connect to the unit. Note: Enter "0000" if a password is requested.
4. When the mobile device has been paired, the BT icon will be displayed on the unit's LCD screen.

Note: To disconnect or reconnect a paired Bluetooth device, press and hold the BT button.

Bluetooth Operation

Play/Pause Button [play-pause]

Press the [play-pause] button to pause or resume Bluetooth playback.

Changing the Track

• Press the [next-track] button to select a higher track.
• Press the [previous-track] button to select a lower track.

Sound Controls

Use the sound controls on the RV6200S to adjust the volume and sound quality.

Note: For optimum sound quality, ensure the media volume on the device is set at 75% or greater.

DISC Operation

Selecting DISC Audio Play Source

When a CD or DVD is inserted, the unit automatically switches to DISC mode and begins playback. If the disc is left inserted, other audio source buttons can be pressed to navigate to other modes, or you can return to DISC mode by pressing the DISC button.

DISC File Selection

• Short press the [previous-track] or [next-track] button to skip to the previous or next audio track. File information will automatically appear in the display.
• Press and hold the [previous-track] or [next-track] button to fast forward or reverse through a selected track.

DIR+ / DIR-

Press the DIR+ / DIR- button to play the next / previous folder from the disc (MP3/WMA files).

Pausing the Audio

Press the [play-pause] button to pause the audio file. Press again to resume playback.

Intro

Press the INT button to play the first 10 seconds of each file. Press again to stop this function.

Repeat

Press the RPT button to repeat a single track or to repeat an entire playlist.

Random

Press the RDM button to play files from a playlist in random order.

Specific Track Number

Press the DISC button to display "NUM 0000". Press the VOL [plus]/[minus] buttons or directly enter the desired track number.

To enter a specific track number using radio buttons, press:

• Buttons 1-6
• EQ button = 7
• [seek-backward] button = 8
• [seek-forward] button = 9
• DISP button = 0

Additional DVD controls are detailed in the remote locations and functions section below.

Remote Control Locations and Functions

• 1. Power On/Off Button [power-symbol]: Press to turn the unit on or off.
• 2. DISC Button: Press to access disc mode.
• 3. Mute Button: Press to mute audio.
• 4. AM/FM, Save Button: Press to select the radio mode. Sequential presses select radio bands: FM1, FM2, FM2 (MHz), AM1, AM2 (KHz). Press and hold for automatic radio station memory storing.
• 5. AUX Button: Press to select between AUX IN and AV IN1.
• 6. Display Button (DISP): Press to toggle through available display information. Press and hold to access clock setting function.
• 7. Play/Pause and Mute Button [play-pause]: Disc: Press to pause DISC/USB play, press again to resume play.
• 8. Random Button: Press to play tracks in random order in DISC/USB mode.
• 9. DIR- Button: Press to navigate back through directories in DISC/USB mode.
• 10. Down [arrow-down], Up [arrow-up] Buttons:
  • Radio Mode: Press to seek/select the next available lower or higher radio frequency.
  • DISC/USB Mode: Press to search for the beginning or next track or chapter.
• 11. SEL Button: Short press to access sound adjustment settings: BASS, TRE, BAL, EQ, and LOUD, and settings BEEP ON/OFF and 12/24 CLOCK. Long press to access AF ON/OFF, TA ON/OFF, radio genre settings, REG ON/OFF, P-VOL, AREA selection, DX/LOC, STEREO/MONO.
• 12. Navigation Buttons [arrow-up], [arrow-down], [arrow-left], [arrow-right]: Moves feature selection up, down, left, or right.
• 13. OK Button: Executes a selected item.
• 14. Stop Button: Press to stop disc play.
• 15. TITLE Button: Returns to the title menu in DVD DISC mode.
• 16. GOTO Button: Selects exact time, track, or chapter in DVD DISC mode.
• 17. Speakers A, B, C Buttons: Press to select speakers to adjust independently or in groups. Press and hold any of the 3 buttons to mute the selected speakers. Press and hold again to resume sound.
• 18. Volume Buttons (VOL [arrow-up] / VOL [arrow-down]): Press VOL [arrow-up] to increase or VOL [arrow-down] to decrease the volume level. Use these buttons to adjust manual sound settings up and down or when selecting ON/OFF settings.
• 19. BT Button: Press to enter Bluetooth mode and access files from a Bluetooth-connected device.
• 20. USB Button: Press to enter USB mode and access files from a USB-connected device.
• 21. RPT Button: Press to select REPEAT ONE or REPEAT ALL in DISC/USB mode.
• 22. INT Button: Press to play the first 10 seconds of tracks in DISC/USB mode.
• 23. EQ/LOUD Button: Short press to select between EQ presets: FLAT, POP, ROCK, CLASS, EQ OFF. Press and hold to toggle between LOUD ON/OFF.
• 24. DIR+ Button: Press to navigate up through directories in DISC/USB mode.
• 25. REV [rewind], FWD [fast-forward] Buttons:
  • Radio Mode: Press to manually tune into a lower or higher radio frequency. Press and hold to rapidly move forward or back.
  • DISC/USB Mode: Press and hold to fast forward or backward through the current selected track.
• 26. SLEEP Button: Press to toggle between SLEEP ON/OFF. Press and hold to enter SLEEP time setting. Once in SLEEP time setting, adjust the time using the VOL [plus] and VOL [minus] buttons.
• 27. ALARM Button: Press to toggle between ALARM ON/ALARM OFF. Press and hold to enter ALARM time setting mode. Once in ALARM time setting, toggle between hours and minutes by again pressing the ALARM button. With either hours or minutes selected (flashing), use the VOL [plus] and VOL [minus] buttons to adjust to the desired time. Note: Ensure the desired AM or PM is selected.
• 28. DIM Button: Press to select screen brightness: LOW, MED, HIGH, or OFF.
• 29. ZOOM Button: Zoom in/out in picture mode.
• 30. SETUP Button: Press to access the DVD setup menu.
• 31. SUB-T Button: Press to access the movie disc's subtitle languages.
• 32. AUDIO/MO/ST Button:
  • Radio Mode: Select STEREO or MONO.
  • DVD DISC Mode: Press to change the audio soundtrack on a multi-audio soundtrack DVD.

BT APP Operation

APP Installation

1. Your smartphone can be used as an alternative way to control the RV6200S. You will need to install the "LINEAR SERIES" app on your smartphone. The APP can be downloaded from Google Play (Android phone) or the App Store (iPhone). Search for "LINEAR SERIES" and proceed to download. Install per the app instructions.

Note 1: Your smartphone must have Bluetooth version 4.0 or above.

Note 2: Before turning on the APP, ensure the unit is not paired with another device.

RADIO Mode

The "LINEAR SERIES" App displays memorized preset radio stations that are set manually or automatically on the RV6200S unit. Refer to page 6 for instructions on Storing Radio Stations under Radio Operations.

All other App operations are detailed below.

To Download App:

• Go to Google Play/Apple store
• Search for 'Linear Series Remote'
• Install application
• Accept any permissions

Installation

• Read the instruction manual carefully before installing the unit.
• Make sure to connect all other wires before powering on the unit.
• To avoid short circuits, ensure all exposed wires are insulated.
• Secure all wires after installation.
• Connect the player according to the wiring connection instructions on page 13 of this manual. Wrong connections may cause damage to the unit.
• This player is only suitable for 12V DC devices.

MOUNTING THE RV6200S

1. Take off the unit's front trim ring.
2. Align the unit to the dash cutout and mounting holes.
3. Secure the unit into the dash with 4 screws.
4. Snap the front trim ring back onto the unit.

Wiring

Important Notes:

• This player operates on 12V DC.
• Do not connect to the battery until the player is absolutely well connected.
• Make sure the red wire is connected to the battery's positive (+) terminal.
• When changing the fuse, ensure the specifications are the same.
• For the best sound from this equipment, use good quality 4-8 ohm speakers.

Trouble Shooting

Specifications

GENERAL

• Power Supply Requirements: DC 12 Volts, Negative Ground
• Chassis Dimensions: 179(W) x 146(D) x 52(H)
• Tone Controls:
• Bass (at 100 Hz): ±10 dB
• Treble (at 10 kHz): ±10 dB
• Maximum Output Power: 4 x 40 watts + 2 x 15 watts
• Current Drain: 15A (max.)

RADIO

Warranty

ONE (1) YEAR LIMITED WARRANTY

Magnadyne Corporation or its authorized agents will, within one year from the date of sale to you, repair, replace, or refund the retail sales price of this product or any part thereof, at the option of Magnadyne Corporation or its authorized agents, if said product or part is found defective in materials or workmanship, when properly connected and operating on the correct power requirements designated for the specific product.

This warranty and Magnadyne Corporation or its authorized agent's obligations hereunder do not apply where the product was: damaged while in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably maintained, utilized in commercial or industrial operations, or serviced by anyone other than Magnadyne Corporation or its authorized agents, or where the warning seal on the product is broken or the power and/or plugs are detached from the unit.

Magnadyne Corporation or any of its authorized agents will not assume any labor costs for the removal and reinstallation of any product found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized agents. Such costs are the sole responsibility of the purchaser.

This warranty does not cover cabinet appearance items or accessories used in connection with this product, or any damage to recording or recording tape, or any damage to the products resulting from improper installation, alteration, accident, misuse, abuse, or acts of nature.

MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE YEAR FROM THE DATE OF SALE.

This warranty extends only to the original purchaser of the product and is not transferable. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights that vary from state to state.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the User's authority to operate the equipment.

Defective merchandise should be returned to the original point of purchase or secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220. Return Authorization must be obtained before sending, or merchandise may be refused.

© Copyright 2020 Magnadyne Corporation. Linear Series is a registered trademark of Magnadyne Corporation.