ZigBee 2-Gang In-wall Switch
Important: Read all instructions prior to installation.
Function Introduction
The device is a 2-gang ZigBee in-wall switch based on the latest ZigBee 3.0 protocol. It supports 100-240VAC wide input and output voltage and can control two separate loads independently. It features screw terminals for safe and reliable input and output connections.
Key Components:
- Reset Key: Used for network pairing, Touchlink, and factory reset of the switch.
- LED Indicator: Off when the device is not added to a Zigbee network; solid on after successful addition. It also indicates the status during network pairing, Touchlink, and factory reset.
- 2 Channels Load Output: L1 and L2 for controlling two separate loads.
- AC Power Input: L and N terminals for power connection.
Product Data
| Input Voltage | Output Voltage | Output Channel | Max. Load | Size (LxWxH) |
|---|---|---|---|---|
| 100-240VAC | 100-240VAC | 2 Channels | Resistive load: max. 8.1A, capacitive load: max. 2.7A | 45.5x45x20.3mm |
Compatible Load Types
| Load Symbol | Load Type | Maximum Load | Remarks |
|---|---|---|---|
| [Light Bulb Symbol] | LED lamps with transformers | 620W @ 230V 290W @ 110V | Maximum number of LED lamps depends on power factor. |
| [Driver Symbol] | LED drivers | 620W @ 230V 290W @ 110V | Maximum permitted number of drivers is 620W divided by driver nameplate power rating. |
| [Incandescent Bulb Symbol] | Incandescent lighting, HV Halogen lamps | 1860W @ 230V 890W @ 110V | |
| [Low Voltage Symbol] | Low voltage halogen lighting with electronic transformers | 620W @ 230V 290W @ 110V |
Key Features
- 2-gang ZigBee in-wall switch with ZigBee 3.0 protocol.
- 100-240VAC wide input and output voltage.
- Supports resistive and capacitive loads.
- 2 channels output, max. total load 8.1A.
- Input and output with screw terminals for safety and reliability.
- Controls ON/OFF of connected loads.
- ZigBee device with 2 endpoints for separate control.
- Supports Touchlink commissioning for direct pairing with ZigBee remotes.
- Supports self-forming ZigBee networks without a coordinator.
- Supports Find and Bind mode.
- Supports Zigbee Green Power and can bind up to 20 Green Power switches.
- Compatible with universal ZigBee gateways.
- Can be controlled by universal single-wire push switches.
- Active power and energy metering functionality.
- Mini size, easy to install in standard wall boxes.
- Radio Frequency: 2.4GHz.
- Waterproof grade: IP20.
Safety & Warnings
- DO NOT install with power applied to the device.
- DO NOT expose the device to moisture.
ZigBee Clusters
Input Clusters: Basic, Identify, Groups, Scenes, On/off, Simple Metering, Electrical Measurement, Diagnostics.
Output Clusters: OTA.
Operation
- Wiring: Perform wiring according to the connection diagram. Ensure correct connections to Live (L), Neutral (N), Switch 1 (S1), Switch 2 (S2), Load 1 (L1), and Load 2 (L2) terminals.
- System Communication: This ZigBee device is a wireless receiver that communicates with ZigBee compatible systems via wireless radio signals.
Zigbee Network Pairing through Coordinator or Hub
- Preparation: If the device is already added to a Zigbee network, remove it first. Refer to the 'Factory Reset Manually' section.
- Add Device: On your ZigBee Controller or hub interface, select to add a lighting device and enter pairing mode as instructed by the controller.
- Power Cycle: Reset the device's power to enter network pairing mode. The connected light will flash twice slowly. This mode has a 15-second timeout; repeat the step if necessary.
- Confirmation: The connected light will blink 5 times and then stay solid on, indicating successful pairing. The device will appear in your controller's menu for control.
TouchLink to a Zigbee Remote
- Proximity: Bring the Zigbee remote or touch panel within 10cm of the lighting device.
- Touchlink Commissioning: Set the remote or touch panel into Touchlink commissioning mode. Refer to the remote's manual for specific instructions.
- Initiation:
- Method 1: Short press the 'Reset' button 4 times (or power cycle the device 4 times) to start Touchlink commissioning immediately. This mode has a 180-second timeout. Repeat if necessary.
- Method 2: Reset the device's power. If not added to a network, Touchlink commissioning starts after 15 seconds (165-second timeout). If already added, it starts immediately (180-second timeout). Repeat if timeout occurs.
- Confirmation: The remote will indicate a successful link, and the connected light will flash twice.
Note on TouchLink:
- Direct TouchLink (both devices not added to a ZigBee network): Each device can link with 1 remote.
- TouchLink after both are added to a ZigBee network: Each device can link with a maximum of 30 remotes.
- For control via both gateway and remote, add both to the network first, then perform TouchLink.
- After TouchLink, the device can be controlled by the linked remotes.
Removed from a Zigbee Network through Coordinator or Hub Interface
Using your ZigBee controller or hub interface, select the option to delete or reset the lighting device as instructed. The connected light will blink 3 times to confirm successful removal.
Factory Reset Manually
Note: If the device is already at factory default settings, there may be no visual indication upon factory reset. All configuration parameters will be reset.
- Reset Method: Short press the 'Reset' key continuously for 5 times, or reset the device's power continuously for 5 times if the 'Reset' key is not accessible.
- Confirmation: The connected light will blink 3 times to indicate a successful reset.
Factory Reset through a Zigbee Remote (Touch Reset)
Note: Ensure the device is added to a network, and the remote is either on the same network or not added to any network.
- Proximity: Bring the Zigbee remote or touch panel within 10cm of the lighting device.
- Touch Reset Procedure: Initiate the Touch Reset procedure on the remote or touch panel. Refer to the corresponding manual for instructions.
- Initiation: Short press the 'Reset' button 4 times to start the TouchLink commissioning process, which has a 180-second timeout. Repeat if necessary.
- Confirmation: The remote will indicate a successful reset, and the connected light will flash 3 times.
Find and Bind Mode
Note: Ensure both the device and the remote are added to the same Zigbee network.
- Initiator Mode: Short press the 'Reset' button 3 times (or reset the device's power 3 times) to start Find and Bind mode. The connected light will flash slowly. This mode has a 180-second timeout. Repeat if necessary.
- Target Mode: Set the remote or touch panel (target node) into find and bind mode, enabling it to find and bind the initiator. Refer to the remote's manual for instructions.
- Confirmation: The remote or touch panel will indicate successful binding, allowing control of the device.
Learning to a Zigbee Green Power Switch
- Initiator Mode: Short press the 'Reset' button 4 times (or reset the device's power 4 times) to start the learning mode for a Zigbee Green Power switch. The connected light will flash twice. This mode has a 180-second timeout. Repeat if necessary.
- Learning Mode: Set the Green Power switch into its learning mode, following its manual's instructions.
- Confirmation: The connected light will flash twice, indicating successful learning. The switch can now control the device.
Note: Each device can learn to a maximum of 20 Zigbee Green Power switches.
Delete Learning to a Zigbee Green Power Switch
- Initiator Mode: Short press the 'Reset' button 3 times (or reset the device's power 3 times) to start the delete learning mode for a Zigbee Green Power switch. The connected light will flash slowly. This mode has a 180-second timeout. Repeat if necessary.
- Learning Mode: Set the paired Green Power switch into its learning mode, following its manual's instructions.
- Confirmation: The connected light will flash 4 times, indicating successful deletion.
Setup a Zigbee Network & Add Other Devices (No Coordinator Required)
- Network Initiation: Short press the 'Reset' button 4 times (or reset the device's power 4 times) to enable the device to set up a Zigbee network. The connected light flashes twice. This mode has a 180-second timeout. Repeat if necessary.
- Add Devices: Set another device or remote/touch panel into network pairing mode and pair it to the network. Refer to their respective manuals.
- Pairing: Pair more devices and remotes to the network as desired, following their manuals.
- Binding: Bind the added devices and remotes through Touchlink so they can be controlled by the remotes. Refer to their manuals.
Notes:
- Each added device can link and be controlled by a maximum of 30 added remotes.
- Each added remote can link and control a maximum of 30 added devices.
OTA (Over-The-Air) Updates
The device supports firmware updates via OTA. It will automatically acquire new firmware from the Zigbee controller or hub every 10 minutes.
Wiring Diagram and Product Dimensions
Wiring Diagram Notes:
- L - Terminal for Live lead
- N - Terminal for Neutral lead
- S1 - Terminal for switch key No. 1
- S2 - Terminal for switch key No. 2
- L1 - Output terminal No. 1 for light load
- L2 - Output terminal No. 2 for light load
The diagram illustrates connections for Live (L), Neutral (N), Switch 1 (S1), Switch 2 (S2), Load 1 (L1), and Load 2 (L2) to the 2-Gang In-wall Switch.
Product Dimensions:
- Width: 45 mm
- Depth: 45.5 mm
- Height: 20.3 mm
The device is marked with [CE Certified], [FC Certified], [RoHS Compliant], and [Zigbee Certified] logos.
Over Current Protection
When the connected resistive load exceeds 8.1A, or the total load exceeds the specified limits, the relay will be forced to turn off and protected.
