Victrola Bluetooth Headphones

Specifications

• SPEAKER: 40mm
• BLUETOOTH VERSION: 4.1
• IMPEDANCE: 32 Ohm
• SENSITIVITY: 107+/-3dB (1KHz, 1mW)
• FREQUENCY RESPONSE: 20Hz~20KHz
• MAXIMUM POWER INPUT: 30 mW
• AUX INPUT: 3.5mm
• CHARGE TIME: 4 hrs
• WORKING HOURS: Over 4 hours
• BATTERY CAPACITY: 250mAh
• RATED VOLTAGE: USB DC 5V 150mA
• AUDIO CABLE: 3.5mm Gold Plated Plug

Accessories Included

• Bluetooth Headphones
• Instruction Manual
• Charging Cable
• 3.5mm AUX Cable

Please note: As a result of continual improvements, the design and specifications of this product are subject to change without notice. Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners. Made in China.

Safety Instructions

Please be sure to read the following instructions before using the Bluetooth Headphones:

1. The device is not intended for use by persons (including children) with reduced physical, sensory or mental capacity. Persons who have not read the manual, unless they have received explanations by a person responsible for their safety and supervision, should not use this device.
2. Children should be monitored to ensure that they do not play with the device.
3. The device should always be readily accessible.
4. The device should not be exposed to dripping or splashing water.
5. Always leave a minimum distance of 10 cm around the unit to ensure sufficient ventilation.
6. Open flame sources, such as candles, should not be placed on top of the device.
7. The device is intended for use only in a temperate climate.
8. At full volume, prolonged listening to the portable audio device may damage the user's hearing and cause hearing trouble (temporary or permanent deafness, hearing drone, tinnitus, hyperacusis).
9. It is recommended not to listen to the device at high audio volume and no more than one hour per day at medium audio volume.
10. The battery can't be replaced by the user, but only by the maker of this product, the after sales department or a qualified person.
11. SWITCH OFF IN RESTRICTED AREAS: Switch the device off where the use of the device is not allowed or where there is a risk of causing interference or danger, for example on board an aircraft, near medical equipment, fuel, chemicals or blasting sites.
12. ROAD SAFETY COMES FIRST: Check the current laws and regulations regarding the use of this device in the areas where you drive. Do not handle the device when driving. Concentrate fully on driving.
13. Radio signals could affect some of the car's electronic systems such as the audio stereo and alarm systems.
14. INTERFERENCE: All wireless devices are susceptible to interference which may affect their performance.
15. All devices conform to international standards and regulations, and if need be national ones, with a view to limiting user exposure to electromagnetic fields. These standards and regulations were adopted after extensive scientific research. This research established no link between the use of the mobile headset and any adverse effects on health if the device is used in accordance with standard practices.

Authorized Personnel

1. Only qualified people are authorized to install or repair this product.
2. Only use batteries, chargers and other accessories which are compatible with this equipment. Do not connect incompatible products.

Keep the Equipment Dry

1. This equipment is not waterproof. Keep it dry.

Keep Out of Reach of Children

1. Keep your device in a safe place, out of the reach of young children. The device contains small parts that may present a choking hazard.

Functions

The Victrola VSG-160 headphones feature several accessible controls and ports:

• Microphone: For calls and voice commands.
• Aux-In Port: For wired audio connection.
• LED Indicator: Displays charging and pairing status.
• Volume Up/Next Track: Controls volume and skips tracks.
• Volume Down/Previous Track: Controls volume and skips tracks.
• Charging/Micro USB: Port for charging the device.
• Power/Play/Pause/Answer/End Call: Multi-function button for power, playback, and call management.

Powering Headphones On & Off

1. Press and hold the Power Button [power button] to power ON or OFF.
2. NOTE: Powering ON: LED illuminates PURPLE then flashes BLUE. Powering OFF: LED illuminates PURPLE, then turns off.
3. Listen for an audible tone. (The LED will not illuminate when Headphones are off.)

To Change the Audio Track

1. Press and hold the [plus button] to go to the next track.
2. Press and hold the [minus button] to restart the current track. Press and hold the [minus button] again to go to the previous track.
3. Quickly press the Power Button [power button] to pause the current track.

Volume

1. Press the [plus button] incrementally to increase volume.
2. Press the [minus button] incrementally to decrease volume.

Charging the Battery

1. Connect the USB cable to a general USB Power Supply.
2. Connect the charger to the outlet.
3. When the charger is connected to the headset, the LED indicator light will remain lit RED. The Headphones will be fully charged in approximately 4 hours. The LED indicator will turn BLUE and remain lit.
4. Once fully charged, disconnect the charger from the headphones and outlet. The headset is now ready for use.

NOTE: The fully charged battery provides around 5 hours of talk time, 4.5 hours of music play time, and up to 200+ hours of standby time. However, talk and standby times may vary based on different mobile phones, compatible Bluetooth devices, usage settings, styles, and environments. When the battery power is low, the headset will give a "Low Battery" alert every 20 seconds, and the red indicator light will start to flash. When using the headphones with an iPhone, an additional battery meter will be shown on your phone displaying the remaining battery capacity.

CAUTION: The built-in rechargeable battery is not replaceable. Do not remove or replace it, do not throw it in the trash or in a fire. Do not dispose of the device in standard garbage disposal sites. Dispose of the device at available Battery Recycling Sites after fully discharging the battery. Failure to do so may violate local disposal laws and regulations. Please refer to local regulations for proper battery disposal.

Pairing the Headphones to Bluetooth

Before using the headset for the first time, you must pair the unit with a Bluetooth-enabled device. Pairing is a one-time process and is required only for the first connection with a mobile phone.

1. Keep headphones within a 33 ft (10m) range of a Bluetooth-enabled device.
2. Press and hold the Power/Play button [power button] for about 5 seconds until the indicator light flashes red and blue intermittently. The device is now in pairing mode.
3. Find the Bluetooth settings of your mobile phone and search for available Bluetooth devices.
4. Choose "VSG-160" from the list of available Bluetooth devices.
5. If required, enter the PIN code "0000" and confirm the entry. Once the pairing process is successful, the headphones will connect to your device automatically. The indicator light will flash blue every 5 seconds when the headset is in standby mode.

Aux-In Function

1. Use the included 3.5mm AUX-IN cable to connect the Headphones with an audio device such as an MP3/MP4 player, smartphone, or tablet.
2. Your audio device (MP3/MP4 player, smartphone or tablet) controls the music playback.
3. Adjust the volume on your device.

NOTE: Volume controls on the headphone will be deactivated when using the AUX-IN function.

Phone Call Function

• Answer: Press the Answer button [power button] quickly to answer the incoming call.
• Reject: Press and hold Answer button [power button] for 2 seconds to reject the incoming call.
• End a call: Press the Answer button [power button] quickly to end a call.
• Re-dial last number: At standby status, double press Answer Button [power button] to re-dial the last number.

Important Information

CALIFORNIA PROP 65 WARNING

"WARNING" This product contains chemicals known to the State of California to cause birth defects or other reproductive harm. For more information on these regulations and a list of chemicals, log on the following website address: http://www.oehha.ca.gov/prop65.html

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The French compliance statement is: le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivates: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Warranty

Victrola is a registered trademark of Innovative Technology Electronics LLC.

Innovative Technology Electronics LLC.

Limited Warranty: 90 Days Labor, One Year Parts

Innovative Technology Electronics LLC. (IT) warrants the product to be free from "Defects" in materials under normal use for a period of "One Year" from the date of the original purchase. The Warranty is "Not" transferable. IT agrees, within the initial "90 Day" period, to repair or replace the product if it is determined to be defective at "No Charge". It is further agreed that IT will cover the cost to repair or replace damaged "Parts" only for a total period of "One Year" from the date of the original purchase. The warranty does not cover cosmetic damage, antennas, AC cords, cabinets, headbands, ear-pads, or damage due to line power surges, connection to improper voltage supply or settings, misuse, mishandling, accident, acts of God or attempted repair by an unauthorized service agent.

To obtain service, the purchaser MUST present an original sales receipt / proof of purchase. Please contact us at www.ithomeproducts.com to request an RMA (Return Material Authorization) number to return products for service or replacement. Returns without an RMA number on the package will be refused and returned to sender. Upon receipt of the returning item and our full inspection (IT) may issue a replacement to customer for the same item or of one that has equivalent value and features. To return an item, supply full name, return address, phone number, item purchased, receipt of purchase and reason for return to obtain RMA number.

All returns must be in the original packaging or reasonable substitute to prevent damage. Customer "Must" include full name, shipping address and telephone number inside of package. No return will be shipped back to a PO Box or APO address.

Please include your check or money order in the amount of:

• USD $5.00 for items $10.00 to $39.99 (Price Paid Per Unit)
• USD $10.00 for items $40.00 to $99.99. (Price Paid Per Unit)
• USD $16.00, for items $100.00 and up. (Price Paid Per Unit)
• Shipping fees are non-refundable

Payment is to be made to Innovative Technology Electronics LLC. (for handling and return shipping charges). (IT) will not be responsible for delays or unprocessed claims resulting from a purchaser's failure to provide any / all of the necessary information.

Send all inquiries or RMA request via our website www.ithomeproducts.com/support.

Innovative Technology Electronics LLC.
1 Channel Drive
Port Washington, NY 11050
Toll free: 1-877-483-2497
Website for support: www.ithomeproducts.com/support

There are no express warranties except as listed above. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CUSTOMER. (IT) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.