ACTIVESHOP CD-4830 Ultrasonic Cleaner User Manual

Technical Specifications

Storage and Handling

• Before filling, unplug the device from the mains. Do not exceed the "MAX" line to avoid overfilling.
• Do not fill the tank with abrasive or corrosive chemicals, as this may cause leaks and damage.
• Do not use the cleaner if the cable or plug is damaged. If damaged, contact a service center for inspection and repair.
• Keep the cleaner in a safe place.
• Never leave the cleaner unattended when connected.
• Do not use the cleaner while bathing.
• Unplug the cleaner immediately after use.
• Do not immerse the cleaner in water to avoid electric shock.
• Water must be drained via the drain hose; never empty the water by tilting the cleaner.

Handling Instructions:

• Do not switch on the cleaner if there is no water inside. Operating the cleaner without water can damage it.
• Do not overload the cleaner with continuous operation. After 45 minutes of continuous use, let the cleaner rest for 20 minutes.
• Do not leave water or solution in the cleaner. Drain water or solution after use. Leaving water or solution in the cleaner for extended periods can damage it.
• Take care of the cleaner's exterior. Immediately wipe off any water or solution residue. Use a damp cloth to clean the cleaner. Wipe dry after cleaning.
• Do not expose the device to direct sunlight for extended periods. Keep the cleaner in a dry and cool place.

User Guide

Step 1: Preparation

Open the lid, place the items to be cleaned in the basket, and then place the basket into the cleaner's tank. Fill the tank with water. The water must cover the items being cleaned but should not exceed the maximum liquid level.

Step 2: Power Connection and Time Setting

Close the lid and connect the cleaner to the mains. The display will show the default operating time. To change the time, use the time adjustment button and the timer button. The timer can be set from 1 to 30 minutes. Commonly selected timer settings are 5, 10, and 15 minutes.

Step 3: Starting and Pausing Cleaning

Press the [ON/OFF button] to start cleaning. The device will beep to indicate it has started. The display will show the remaining operating time. You can pause the cleaning at any time by pressing the [ON/OFF button]. The device has an overheat protection system. If the red light is on, the device will not turn on. After approximately 20 minutes, a green indicator light will illuminate, indicating that the device can be used again.

Step 4: Selecting Cleaning Modes and Settings

Select one of the four cleaning modes.

• a) Temperature Adjustment: To increase the temperature, press the [TEMP button] and select one of the 5 possible temperatures. Press the [HEATER button] to start heating, indicated by a [heating indicator]. When the device reaches the selected temperature, the indicator disappears. The percentage of the achieved temperature is displayed.
• b) Degassing Function: When cleaning with a solution, it is recommended to use the degassing function to speed up the process. Press the [TIME button] and set the time to 10 minutes. Then, press the function button. The [degassing icon] will illuminate. Press the [ON/OFF button] to start degassing, which lasts for 2 minutes, after which normal cleaning begins.

Step 5: Draining and Finishing

When you have finished, switch off the device and unplug it from the mains. Open the lid and remove the items. Connect the drain hose to the water drain, open the drain valve using the [drain button], let the water drain out, clean the device, and wipe it dry. Disconnect the hose and close the valve.

Cleaning Procedures

1. Regular Cleaning

Place the items to be cleaned in the basket and insert it into the cleaner's tank. Fill the tank with water. The water must cover the items being cleaned but should not exceed the maximum liquid level. Place the lid on and connect the machine to the mains. Press the [TIME button] to set the operating time (5-10 minutes) and then press [ON/OFF button] to start cleaning.

2. Intermediate Cleaning

If items need to be washed with a cleaning solution, it is recommended to place them directly into the tank instead of using the basket. Follow the same procedure as for regular cleaning.

3. Advanced Cleaning (for heavily soiled items)

Large items can be placed directly in the tank, while smaller items are better placed in the basket. Fill the tank with water. The water must cover the items being cleaned but should not exceed the maximum liquid level. Then, add 50 ml of cleaning solution and set the temperature to 45 °C using the [TEMP button]. Then, press the [HEATER button] and close the lid. Set the cleaning time to 15 minutes and switch on the machine using the [ON/OFF button]. When finished, drain the water from the machine, fill it with clean water, and run the machine for another 3 minutes to rinse off detergent residue.

4. Special Cleaning (for tarnished silver or brass items)

Place the items in the basket and insert it into the cleaner's tank. Fill the tank with water. The water must cover the items being cleaned but should not exceed the maximum liquid level. Then, add a suitable special cleaning solution for silver. Place the lid on and connect the device to the mains. Set the temperature to 50 °C and wait for the device to heat up. Then, press the [h/min button] to adjust the solution working time. 40 minutes or 1 hour is recommended. Then, press the [TIME button] and set the time to 15 minutes, and press the function button to start degassing. The [degassing icon] will illuminate. Press the [ON/OFF button] to start removing gases. This lasts for 2 minutes, after which normal cleaning begins. When finished, drain the water from the machine, fill it with clean water, and run the machine for another 3 minutes to rinse off any remaining detergent.

Cleaner Construction and Accessories

Construction:

• A. Viewing window
• B. Lid
• C. Tank
• D. Body
• E. Drain button
• F. Water drain
• G. Ventilation
• H. On/Off switch
• I. Power cord socket
• J. Plastic basket
• K. Drain hose
• L. Power cord
• M. Control panel

Control Panel and Functions

1. Time display: The time is read when the cleaner is running.
2. Temperature indicator:
   • Green light indicates 0-30% of the set temperature has been reached.
   • Orange light indicates 30-60% of the set temperature has been reached.
   • Red light indicates 60-90% of the set temperature has been reached.
   • Flashing red light indicates the liquid is close to 60-90% of the set temperature.
   • All lights on indicate the set water temperature has been reached.
3. Display of set temperature: Press the button to set one of 5 temperatures: 40°C/104°F, 45°C/113°F, 50°C/122°F, 55°C/131°F, 60°C/140°F.
4. °C/°F: Indicates the temperature unit.
5. Solution working time: Solution working time, calculated in hours.
6. Solution working time indicator: When the solution working time reaches zero, the indicator light will flash, indicating the need to change the liquid.
7. Drain function indicator: Light on - function selected. Light flashing - function working.
8. Preheat function indicator: Light on - function activated.
9. Cleaning function indicator: Light on - the cleaner is operating in normal mode.
10. Machine operation indicator: Green - the cleaner is ready. Red - overheat protection activated. Wait for the light to turn green (20 minutes or longer).
11. Degassing function button: Press to select the degassing function. Press the [ON/OFF button] to activate it (duration - 2 minutes). Degassing: In some cases, air bubbles (gas bubbles) may form in the solution due to chemical reactions. Gas bubbles hinder the normal operation of the cleaner. Activating the gas removal function helps remove these bubbles and thus improves the cleaner's performance.
12. Temperature adjustment button: Press the button to change the set temperature to the desired temperature.
13. Time adjustment button: Press the button to set the desired time. Each press increases the time by 5 minutes.
14. On/Off button: If the cleaner is switched on via the [power switch H], it is ready for use. Pressing the [ON/OFF button] starts/stops the machine. The cleaner will automatically switch off when the time reaches 0:00.
15. Solution time control button: Each time this button is pressed, the time increases by 20 minutes. For example, 1:20 means 1 hour and 20 minutes. The maximum possible time is 9 hours and 60 minutes.
16. Time/temperature decrease button:
    • When setting working time (function 13) - pressing decreases the time by 1 minute.
    • When setting temperature (function 12) - pressing decreases the temperature by 1 step.
    • When setting solution time (function 15) - pressing decreases the time by 20 minutes.
17. Heating activation button: Pressing activates the heating function. Pressing again turns off the heating function. Heating automatically switches off when the cleaner's operating time reaches 0:00.

Items NOT Suitable for Ultrasonic Cleaning

• Fine jewelry (pearls, emeralds, ivory items, beads, shells, agate).
• Welded, coated, and glued items.
• Other items such as wood, coated glass, ceramics, camera filters.

Safety Measures

1. The device is a professional unit intended for use in beauty salons. Use by qualified cosmetic personnel avoids undesirable consequences during treatment.
2. The device must not be disassembled or attempted to be used for purposes other than those specified in this user manual. All maintenance and repair work must be carried out only by an authorized service technician (ACTIVESHOP Sp. z o.o.).
3. Do not install or use the device near liquids, in wet places, or with wet hands, to prevent liquid from entering the device.
4. In the following cases, unplug the device immediately and contact the authorized service provided by ACTIVESHOP Sp. z o.o.:
   • a) Liquid has entered the device.
   • b) The device emits a strange smell, smoke, or makes unusual noise.
   • c) The power cord is damaged.
   • d) The device has been dropped or its casing is damaged.
5. Do not place any objects on the cords. Do not place the device in a location where someone might step on the power cord.
6. For safety reasons, unplug the power cord from the socket each time you finish working with the device.
7. Do not insert anything into the device's openings. If a foreign object enters an opening, unplug the cord and contact the dealer or manufacturer.
8. Do not place the device on an unstable cart, shelf, or vehicle. The device may be damaged if it falls.
9. To ensure the device's longevity, it is recommended to wait one minute between pressing the power button again (switching on and off, and vice versa).
10. The power supply must comply with the specifications on the nameplate. Otherwise, there is a risk that the device may not operate correctly, may be damaged, or may even burn out.

ATTENTION:

• In case of damage to the power cord or other malfunctions, contact an authorized service center to avoid danger.
• This device can be used by children aged 8 and above, and by persons with reduced physical and mental abilities, or lack of experience and knowledge, provided they are supervised or instructed on safe use and understand the associated risks.
• The device is not intended for children to play with. Do not allow children to play with the device.
• Do not leave the device unattended if children or persons not sufficiently aware of its use are nearby.
• This electrical device is not a toy. Improper use or contact with the electrical device can pose a health risk or cause death; therefore, the device must be used and stored in a place inaccessible to children.

Device Disposal

Dispose of used electrical equipment, lighting, and packaging at recycling centers in accordance with environmental protection regulations. Electrical equipment must not be disposed of in household waste bins. Follow the regulations for disposing of this type of equipment. To protect the environment, in accordance with Directive 2012/19/EU on waste electrical and electronic equipment, electrical equipment waste must be collected separately and handed over to collection points for waste electrical and electronic equipment.

Used and old devices contain fully recyclable components and should therefore be sent for reprocessing. They should therefore be handed over to appropriate collection points or to ACTIVESHOP Ltd.

Storage and Transport

The device must be transported at temperatures between -20 °C and +50 °C only in its original packaging. Store the device in a well-ventilated room with relative humidity not exceeding 75%. The operating temperature is +10 °C to +40 °C. During storage and transport, the device must not be dropped or allowed to fall, and must not be exposed to mechanical shocks or weather conditions.