Contents
- Teddy head x 1 (Illustration of a teddy bear head)
- Teddy front body x 1 (Illustration of the front torso)
- Teddy back body x 1 (Illustration of the back torso)
- arms x 1 (Illustration of two separate arms)
- legs x 1 (Illustration of two separate legs)
- giftbox A x 1 (Illustration of a gift box)
- giftbox B x 1 (Illustration of a gift box)
- Fixing Hook x 2 (Illustration of a hook)
- Fixing rope x 10 (Illustration of rope)
Assembly Diagram
Step 1
Illustration shows the Teddy back body and front body parts aligning, with arrows indicating how they fit together. The back body is shown with internal components visible, and the front body is shown aligning with it.
Step 2
Illustration shows the arms and legs being attached to the main teddy body. Arrows indicate connection points.
Step 3
Illustration shows the fully assembled teddy figure, including the head, arms, and legs attached.
Adaptor Manual
Please use the equipment according to the rated voltage and current.
| Model No. | Voltage | Input Rated Frequency | Current | Output Rated Voltage | Power |
|---|---|---|---|---|---|
| JT-DC4.5V3.6W-E4 | 220-240VAC | 50-60Hz | 0.10A Max | 4.5V DC | 3.6W |
1. Please use the equipment according to the rated voltage and current.
2. Do not open the cover of the equipment.
3. For use with LED lighting equipment.
4. The input and output voltage should be checked before use to ensure correct use.
5. This is the Class II product, only for indoor use.
6. The product is not a toy, keep it where children cannot reach.
7. The lamp controlgear does not rely upon the luminaire enclosure for protection against accidental contact with live parts.
8. If applicable: an indication that the controlgear is suitable for operation with LED modules.
9. Do-not-cover classification.
Safety Clearance for Flammable Materials
The LED driver can be used where normally flammable materials, including building insulation, are present, but cannot be abutted against any material and cannot be covered.
Minimum clearance distance from the top and sides of the control gear to normally flammable building element is 75mm.
Diagram Description: A diagram illustrates required clearance around the LED driver. Labels A, B, and C indicate minimum 75mm clearance from the LED driver to a combustible structural member and to combustible building elements above. A note specifies that a barrier is required for loose fill insulation or loose combustible materials.
Warnings
- The light chain is suitable for INDOOR and OUTDOOR USE.
- This product is NOT designed for permanent or long-term use.
- The LED driver MUST be installed INDOOR, away from weather.
- The LED driver is suitable for operation of LED Modules only.
- Only operate this light chain with the LED driver, Model No. JT-DC4.5V3.6W-E4.
- Do not connect this light chain electrically to another light chain.
- Do not operate the product while it is in the packaging.
- DO NOT attempt to replace the non-replaceable bulbs in this light chain.
- Never allow any part of the set to come into contact with a source of heat or flame.
- Care must be taken to avoid damage to the cable or fittings.
- If any part of the light set or cable is damaged, the light set MUST be discarded.
- This product is for use as a decoration only. Not to be used by children as a toy. Keep out of reach of children.
- Do not position this light chain where it will be exposed to extreme wet weather or submerged in water.
- Always switch off this light set or unplug an adaptor if unattended.
- DO NOT overload power sockets or extension leads.
- DO NOT pierce the cable when securing in place, bend, or stand on the light chain, as this will damage the bulbs or wiring.
- Please refer to the packing or product rating label for product class, specifications, and rating.
