Furrion Digital Wireless Camera System

Introduction

Thank you for purchasing the Furrion Digital Wireless Camera System. This system is designed for 5th Wheel, RV, Caravan, and Trailer applications, offering an easy-to-install solution for rear-view monitoring.

The system comes in two main parts:

• Furrion Mount Bracket Prep Kit. Part No. FRCBRKT-BL
• Furrion Camera and Monitor Kit. Part No. FRC12TA-BL

Before installation, check if your RV or Trailer has been pre-installed with the mounting bracket prep kit.

The image shows the Furrion Digital Wireless Camera System components: a monitor with a suction cup mount, a camera unit with an antenna, and two black mounting brackets. The monitor displays the Furrion logo. The camera unit has a lens and LEDs.

Safety Instructions

Please read these instructions carefully before installation and operating your Furrion reversing camera unit.

The following symbols are used throughout this manual to indicate potentially dangerous situations or mark important safety instructions:

• ⚠️ WARNING: Indicates a potentially dangerous condition. Use extreme caution when performing this task.
• ❗ CAUTION: Indicates a critical procedure for safe and proper operation of the controller.
• ? NOTE: Indicates a procedure or function that is important for the safe and proper operation of the controller.

General Safety Information

• Read all instructions and cautions before beginning installation.
• There are no user-serviceable parts inside the Furrion Rear camera system. Do not disassemble or attempt to repair any part of the camera system.
• Disconnect all sources of power to the camera before installing.
• There are no fuses or disconnects on the Furrion reversing camera unit. Install external fuses/breakers as required.
• Do not allow water to enter the LCD Display.
• Connect 12/24V power cable to the camera unit using waterproof connectors.
• Excessive heat can be caused from a loose connection.

Electrical Safety

• ❗ Caution: A battery or 12/24V DC electrical system presents a risk of electrical shock or burn hazard. Ensure all power sources are isolated before installation.
• ⚠️ Warning: These installation instructions are for use by qualified personnel only. To reduce the risk of electric shock, do not perform any servicing other than that specified in the operating instructions.
• ❗ Caution: To reduce the risk of fire, connect the camera only to a circuit provided with a maximum branch-circuit over current protection device.
• ? Note: Ensure to use watertight connectors when connecting the camera power supply cable to the power source.
• ⚠️ Warning: Use 16AWG or larger cables to supply power to the camera unit.
• ⚠️ Warning: Ensure to connect the rear camera to the correct polarity 12/24V DC power supply. Red = Positive.

Installation Safety Precautions

• Use correct size cable and connectors for supplying power to your rear camera.
• Ensure the power supply circuit has circuit protection.
• Connect rear camera to a 8-30V DC circuit only.
• Use insulated tools when working with power supply.
• Use correct safety equipment when working at elevated levels.
• Ensure camera prep bracket gasket is correctly sealed and weatherproof.
• Ensure correct polarity of DC power supply to camera.
• Objects in monitor may appear closer than they appear. Reverse slowly and with care.
• This rear view camera system is designed to assist the driver; it is not designed to replace rear view mirrors. Always check your mirrors.

General Information

Overview

Thank you for purchasing a Furrion reversing camera system. Furrion's reversing camera system is one of the easiest rear view camera systems to install in your trailer, truck, or RV. All that is required is a connection of a single DC power supply to the rear camera from a reversing power source.

The Furrion reversing camera system uses digital wireless technology, providing superior signal transmission with low interference on a single bandwidth channel. This means the Furrion camera unit eliminates interferences that affect analog signal systems, delivering a clearer picture of what is behind you.

This Furrion system, with an integrated antenna attached to the camera, is specifically designed for use on trailers, trucks, 5th wheels, caravans, and RVs. It is designed for extended range applications or security monitoring.

Features

• Can be used as a reversing camera, tow hitch monitor, or security monitor.
• Wide angle viewing lens.
• Night vision LED lights.
• Camera mounting bracket to reduce glare.
• Digital wireless signal for clear picture quality.
• Easy installation.
• Adjustable camera angle.

Installation

Furrion Reversing Camera Mounting Bracket Installation (FRCBRKT-BL)

The Furrion reversing camera prep kit includes:

• 1 x Reversing camera mounting bracket
• 1 x Mounting bracket gasket
• 1 x 6ft power cable
• 1 x Removable Bracket cover

When wiring the Furrion camera system as a rear view camera, the power supply for the camera unit must come from a 12V trigger power source or transmission wiring. The power source can also come from the 7-way connection from your trailer.

For reversing camera use, mount the camera bracket on an elevated position at the rear of the trailer or RV.

Diagram Description (Page 7): An illustration shows an RV or trailer with the Furrion camera mounted correctly on the upper rear section. A dashed line indicates the camera's viewing area. Text notes to connect camera power cable to reversing backup lights or 7-way cable, meaning the camera activates when reverse gear is selected.

Important Notes for Mounting:

• Do not mount the camera in a low position.
• For reversing camera function, do not connect the camera to a constant power source.
• For best results, mount the camera in a high position to increase the viewing angle.

Mounting and Wiring the Camera Prep Bracket Kit

Wiring: For using your camera kit as a reversing camera system:

1. Isolate the 12V power system.
2. Find a suitable position to mount your camera mounting bracket on the rear of your trailer/coach/truck. Ensure the mounting position is centered and elevated at the top area. A higher mount provides a better viewing angle. Ensure there are no running lights or objects protruding directly under the position that will obscure camera vision.
3. Drill a hole large enough to run the 16AWG 2-core cable supplied with the mounting bracket. After drilling, remove any sharp edges or burrs to prevent cable damage.
4. Before running the 12V supplied power cable through the hole, feed the supplied 6ft power cable through the hole in the bracket gasket. Ensure the center square on the gasket faces out towards the cable connector.
5. To provide power to the wireless rear view camera, you will need to run a 16AWG 2-core internal cable from your 12V trigger source on the rear of your trailer/coach/truck. Furrion supplies a 6ft 12V power cable with the mounting bracket. Additional cable may be required if the distance to the trigger power supply is not long enough.
6. When connecting the cable to the 12V power source, connect (+ to Red) and (- to Black).
7. Attach the camera prep mounting bracket using 4 screws. Ensure the gasket is lined up correctly and the bracket is mounted tightly to ensure weatherproofing.

Diagram Description (Page 8): Illustrates feeding the connector through the PVC gasket and a 5/8" hole. Shows securing the mounting bracket to the back of a trailer or RV with 4 screws. Another illustration shows affixing the cover if only the prep kit is being installed, securing the wire connector inside.

Diagram Description (Page 8, Wiring): Shows two power source options: "12V DC from 7 Way connection" and "12V DC from trigger power source", both connecting to the "Connection cable supplied with prep kit" which leads to the "Furrion camera". A note indicates using one of these power sources for 12/24V DC supply when used as a reversing camera.

Installation of Camera

If your RV or trailer has a Furrion reversing camera prep kit pre-installed by the OEM manufacturer, you will need to contact your local dealer or go to furrion.com to purchase a Furrion FRC12TA-BL Camera and Monitor Installation Kit.

To install the camera onto a pre-installed mounting bracket:

1. Remove the cable cover, held by 4 screws on the underside of the bracket.
2. Locate the connector inside the prep kit mounting bracket.
3. Connect the camera plug and socket together and install the camera with the 4 screws.

Diagram Description (Page 9): Shows the camera unit being attached to the pre-installed bracket. Text indicates that the camera viewing angle can be adjusted after mounting.

Monitor Installation

When choosing a location to mount the monitor, ensure it is in an area that will not obstruct your vision while driving.

1. Before mounting, clean the mounting surface thoroughly.
2. Position the suction mount to a smooth surface that suits your requirement.
3. Press the suction cap against the smooth surface and press the lock down to attach and fix the mount to the surface.

Diagram Description (Page 10): A sequence of three images shows the process of attaching the suction mount: pressing the cap onto the surface, and then locking it down.

4. Adjust the mounting arms to suit your view angle and tighten the screws on the mount to fix the position.
5. Route the power cable to the vehicle's cigarette lighter socket/12/24V power outlet. The cable must not interfere with the safe operation of the vehicle.
6. Insert the small 12/24 Volt DC plug of the power cable into the right side of the monitor.
7. Plug the 12/24 Volt cigarette lighter plug into the vehicle's cigarette lighter socket.

To maximize the effectiveness of the suction mount, it is recommended that the application be performed under the following conditions:

• Surface temperature should be between 21 and 38 degrees Celsius (70-100°F).
• Application below 10 degrees Celsius (50°F) should be avoided.
• Application should not occur in direct sunlight.
• Mounting should be protected from exposure to direct sunlight for a period of 24 hours.

NOTE: UNDER EXTREME BRIGHT LIGHT CONDITIONS, THE SCREEN IMAGE MAY TAKE A FEW SECONDS TO STABLIZE. PLEASE WAIT UNTIL THE IMAGE HAS STABLIZED BEFORE BACKING UP.

Operation

Once the camera is fitted, you will need to pair the wireless camera with the LCD monitor before use. This is only required at initial system commissioning.

Diagram Description (Page 11): Shows the Furrion LCD monitor with buttons labeled Menu, Up, Power/Confirm, Down, and Line. A table below details the function of each button.

Connecting Camera Unit and Screen Together (Pairing)

1. Ensure both the rear camera and LCD display have 12/24V DC power supplied (the vehicle may need to be running and in reverse gear to supply power to the camera).
2. Press the power button on the LCD display to turn it on.
3. Press the MENU button on the display. This will bring up 4 icons on the screen.
4. Using the UP and DOWN buttons, scroll to the PAIR icon.
5. Press the POWER/CONFIRM button (short press). The "pairing" icon will be displayed.
6. Press the small button on the underside of the camera unit for 2 seconds.
7. On successful pairing, "OK" will be displayed on the LCD display.

If there is no operation of the camera displayed on the LCD display within 30 seconds of pairing, repeat the pairing process.

Note: If you are having trouble pairing, reduce the distance between the camera unit and the LCD display for the pairing process.

To remove or replace a paired camera from the LCD display memory: Exit the menu icons on the LCD display, then press and hold the DOWN key for 5 seconds. This will erase all pairing memory stored on the LCD display. The pairing process must be completed again for the system to function.

LCD Display Menu Icons

• Signal strength indicator: ? (e.g., C1, Y)
• Mirror/rotated image indicator: ?
• [picture-settings-icon] Picture Settings
• [rotate-icon] Rotate Camera Image
• [connect-icon] Connect Camera
• [info-icon] Software Information

Using the UP and DOWN arrow buttons on the monitor, select the desired icon, then press the POWER button to confirm selection.

Two Camera Option

This system can support 2 separate cameras paired to a monitor.

This feature enables two separate cameras to be paired with the same monitor. The cameras can be mounted in separate locations if required. Once both cameras are paired, use the UP and DOWN buttons on the monitor to scroll between the camera views. Both cameras require a constant power supply to enable switching views.

When two cameras are paired to the system, they are not required to be connected to the trigger power supply; a constant power source is required to be able to scroll between cameras using the UP and DOWN buttons on the monitor.

⚠️ WARNING: When cameras are wired to a constant power source, do not use the monitor while driving. Driving with a monitor on can be a violation of state law. Check legislation before use.

When the PAIR icon is selected, a sub-menu will be displayed showing:

• Master Select
• Pair 1
• Pair 2

When pairing 1 camera, select Master Icon. When pairing 2 cameras, select Pair 1 and Pair 2 for each camera.

LCD Picture Settings Sub Menu Icons

• ☀️ Brightness Adjust
• ? Contrast Adjust
• ? Color Adjust

Trouble Shooting

System Testing

1. Disconnect and reattach the vehicle's negative battery cable.
2. Turn the ignition key to the accessory position; do not start the vehicle.
3. Engage the parking brake, and then put the shifter in the reverse position. This will engage the camera unit and the picture will be displayed.
4. After testing the unit and you are satisfied with the route chosen for the cabling, you must permanently install it.
5. Route all wires behind interior panels or under carpeting so they are hidden.

Technical Specifications

LCD Display

1. Working voltage: DC8-30V
2. Working current: ≤180mA
3. Standby current: ≤5mA
4. Wireless communication distance: ≥100 FT (open area outdoors)
5. Working frequency: 2.4GHz
6. Size of LCD display: 4.3'
7. Effective pixels of LCD: 480*272
8. Sensitivity of receiver: -87±3dBm
9. Working temperature: -10/+50 °C

Camera Unit

1. Working voltage: DC8-30V
2. Working current: ≤220mA
3. Transmitting distance: ≥100 FT (open area outdoors)
4. Size of image sensor: 1/4 inch Color CMOS VGA
5. Quality of image: Max. 25 frame/sec @ QVGA (frame rate adjusts dynamically according to the image)
6. Specification of camera: Focal length f1.7mm, aperture F2.0, IR filter 850nm
7. IR emission wavelength: 850nm
8. IR view distance: ≥1.5M
9. IR LED lit condition: Brightness ≤2Lux
10. Working temperature: -10/+50 °C

Product Information

Product: 2.4GHz Digital Wireless Camera System

Trade Name: FURRION

Model Name: FRC12TA-BL

Serial Model: FCA48TA-BL, FCS43TA-BL

FCC ID: 2ABH3FRC12TA-BLC / 2ABH3FRC12TA-BLM

* This product is backed by Furrion's 12-month product warranty. See warranty card for terms and conditions.