Jula Meec Tools 051-010 Hot Air Gun

Safety Instructions

• Read these Operating Instructions carefully before use.
• Never leave the machine unattended when children are present.
• Check that the mains voltage corresponds with the rated voltage for the tool.
• Never use the tool if it shows signs of damage.
• Do not tie knots in the power cord.
• Always check that the power cord is in perfect condition. Risk of potentially fatal electric shock.
• Never use the machine if it has been dropped on the floor or is damaged or if the power cord and/or plug are damaged.
• The machine is intended for temporary use only.
• Make sure the On and Off button is in the middle position before plugging into the mains.
• The nozzle heats up to 600°C. Caution - fire hazard!
• Always wear gloves and eye protection.
• Do not touch the nozzle when in use.
• Allow the hot air gun to cool completely before putting it away.
• Never expose the machine to rain or moisture. Store in a dry place.
• Never leave the machine unattended.
• Keep children away from the machine.
• Never point the air flow at people or animals.
• The machine must not be used for drying clothes or hair.
• Do not use in the vicinity of flammable or explosive substances or gases.
• Do not obstruct the hot air flow by blocking or shielding the nozzle.
• Only use original accessories and spare parts from the manufacturer.
• Do not wear loose-fitting clothing or jewellery. Wear non-slip shoes and use a hair net if you have long hair. Make sure you have a firm footing when working.
• Never use the machine in a wet environment or in areas with a high humidity level (bathrooms, saunas, etc.). Do not immerse any part of the machine in water. Risk of electric shock.
• Remove flammable substances and materials from the workplace before using the hot air gun.
• Do not carry the hot air gun by the power cord.
• Only use an extension cord with a minimum cable area of 1.5 mm².
• Never use chemical removers or solvents at the same time as the hot air gun.
• Clean the nozzle if it gets dirty.
• Make sure that the vents for the air intake and hot air blower are always kept clean and free from dirt.
• Paint removal can create hazardous and/or toxic fumes. Ensure satisfactory ventilation when working indoors.
• Never point the hot air directly at windows or other glass surfaces.
• Always unplug from the mains supply before cleaning and carrying out maintenance work.
• The power cord must only be replaced by the supplier.
• Repair work must be carried out by the supplier.

Technical Data

Description

The hot air gun is intended for heating shrink hoses, removing paint, and for joining and shaping plastic materials.

The hot air gun is illustrated and described below, showing the main unit and its various attachments:

• 1. Nozzle
• 2. 2-position switch
• 3. Hanger device
• 4. Power cord
• 5. Glass protector nozzle
• 6. Flat nozzle
• 7. Reducer nozzle 20 mm
• 8. Reflector nozzle

Operation

WARNING! High temperatures can result in a serious risk of fire or explosion! Make sure that the workplace is well ventilated. Gases and fumes can be hazardous to health and/or toxic.

Select the required working temperature and air volume with the switch (2). The hot air gun reaches its working temperature within one minute.

• Switch in position 1: 1st step - 375°C / 400 litres/min
• Middle position: The hot air gun is disconnected.
• Switch in position 2: 2nd step - 500 / 550 litres/min

Possible Uses:

• 1. Paint and varnish removal. Note: The removal of paint and varnish can create hazardous and/or toxic fumes. Make sure there is adequate ventilation.
• 2. Removing sticker labels and decorations.
• 3. Removal of rusty or tight nuts and metal screws.
• 4. Thawing of frozen pipes, door locks, etc. Note: do not thaw pipes made of plastic or other synthetic materials.
• 5. Accentuation of natural graining of wooden surfaces before staining or varnishing.
• 6. Shrinking of PVC foil packaging and insulation hoses.
• 7. Waxing and dewaxing of skis.

Selection of Nozzle:

• The glass protector nozzle (5) deflects the air flow and protects windows from overheating.
• For removing paint, the flat nozzle (6) is used for an even distribution of air over small surfaces.
• The reducer nozzle (7) is used to concentrate the air flow at corners and when joining.
• The reflector nozzle (8) is used for joining and shaping pipes, thawing water pipes and shrinking insulation hoses.

Maintenance

Make sure that the vents for the air intake and hot air blower are always kept clean and free from dirt. Clean the hot air gun with a moist cloth and standard household detergent. Never use solvents or the equivalent for cleaning.

Contact and Environmental Information

Subject to printing errors and design changes over which we have no control. In the event of problems, please contact our service department.

Jula AB, Box 363, SE-532 24 SKARA, SWEDEN
www.jula.com

Care for the environment! Must not be discarded with household waste! This product contains electrical or electronic components that should be recycled. Leave the product for recycling at the designated station, e.g. the local authority's recycling station.